Amendment in Table A of Schedule 2 and Appendix 3 of ITC(HS) Classification of Export and Import Items
{To be published in the Gazette of India Extra Ordinary Part-II, Section-3, Sub section (ii)}
Government of India Ministry of Commerce and Industry Department of Commerce Directorate General of Foreign Trade Udyog Bhawan, New Delhi
NOTIFICATION No.5 /2015-2020
New Delhi, Dated: J. ~ April, 2017
Subject:- Amendment in Table A of Schedule 2 and Appendix 3 of ITC(HS) Classification of Export and Import Items
S.O.(E} In exercise of the powers conferred by Section 5 and Section 14A of the Foreign Trade (Development & Regulation) Act, 1992 (No.22 of 1992) read with Para 1.02 of the Foreign Trade Policy,
2015-2020, as amended, and in supersession of DGFT Notification NO.38 (RE-2010) /2009-2014 dated 31st
March, 2011, Notification no. 93(RE-2012}/2009-14 dated s" January 2012, Notification no. 37(RE-
2012}/2009-14 dated 14th March 2013, Notification no. 26(RE-2013}/2009-14 dated 3rd July 2013,
Notification no. 56 (RE - 2013}/2009-2014 dated iz" December 2013, Notification no. 115 (RE -
2013}/2009-2014 dated is" March 2015, Notification no. 116(RE-2013)/2009-14 dated 13th March 2015,
Notification no. 05/(2015-2020) dated 29th April 2016 and Notification no. 38/(2015-2020} dated 17th February 2017, except as respects acts done before such supersession, the Central Government hereby
makes the following amendments in Table A of Schedule 2 and Appendix 3 of ITC(HS} Classification of Export and Import Items. Annexure to this notification will replace the existing 'Appendix 3' to Schedule 2 of ITC (HS) Classification of Export and Import Items, 2012.
| 2. Serial No. (S. No.) 4 and 5 of the Table A of Sched Import Items is substituted as under: | ule 2 of ITC | (HS) Classification of Export and |
| Goods falling in more than one Chapte 1/4 - - | r of ITC (HS) - | Classification - |
| 5 Any Special Chemicals, chapter Organisms, Materials, Equipment & Technologies (SCOMET) items as specified in Appendix-3 of this Schedule. | Proh Rest | ibited/ a. Exports would be governed as ricted per the conditions indicated in Appendix-3 of this Schedule. b. Export of items specified in Category 0 of the SCOM ET list is governed by the extant provisions of the Atomic Energy Act 1962 as amended and rules, regulations, guidelines and resolutions issued under the said Act. Unless otherwise prohibited, export may be permitted against an authorization granted by the Department of Atomic Energy. c. Export of items specified under the Note 2 of the 'Commodity Identification Note' of the SCOMET list would be permitted against an authorization granted by the Department of Atomic Energy. d. Export of items specified in Category 6 of SCOMET list (Munitions List), (except those covered under Note 2 and 3 of Commodity Identification Note of the SCOMET list) is governed by the extant Standard Operating Procedure issued by the Department of Defence Production in the Ministry of Defence. Unless prohibited, export may be permitted against an authorization issued by the Department of Defence Production. e. Export of items specified in Categories 1, 2, 3, 4, 5, 7 and 8 of the SCOMET list is governed by the notifications, public notices and circulars issued under the Foreign Trade (Development and Regulation) Act 1992 as amended. Unless otherwise prohibited (including the items covered under Note 4 of the Commodity Identification Note of the SCOMET list), export of such items may be permitted against an authorization issued by the DGFT. /I |
3. 'Appendix 3' to Schedule- 2 of ITC (HS) Classification of Export and Import Items, 2012 contains
| the list of specified goods, services and technologies, i.e. Special Chemicals, Organisms, Equipment and Technologies (SCOMET). Annexure to this notification contains the revised 'Appendix 3' | Materials, |
and the same is also available in the DGFT's website www.dgft.gov.in.
SCOMET Categories in which amendments have been made are as follows:-
| a) | SCOMET Category 6 titled 'Munitions List' that was hitherto 'Reserved' has been populated. The Military Stores list notified vide Notification No. 115(RE-2013/2009-2014 dated 13th March 2015 stands rescinded. |
| b) | A new SCOMET Category 8 titled 'Special Materials and Related Equipment, Material Processing, Electronics, Computers, Telecommunications, Information Security, Sensors and Lasers, Navigation and Avionics, Marine, Aerospace and Propulsion' has been added. |
| c) | In SCOMET Category 18 and 1C, amendments have been made. SCOMET Category 10 titled 'Other Chemicals' has been added. |
| d) | SCOMET Category 2 has been substituted with amended and new entries. |
| e) | SCOMET Categories 30001 to 30005 have been substituted by entries 30001 to 30015. |
| f) | Categories 3A201, 3A303, 3A309, 4A003, 4A007, 4A017, 48006, SA102, SA20S have been substituted with amended and new entries. |
| g) | SCOMET Category 7C has been deleted. |
4. This notification shall come into force on the i" of May, 2017.
5. Effect of this notification: Annexure to this notification contains the revised 'Appendix 3' to
Schedule- 2 of ITC (HS) Classification of Export and Import Items which will replace the existing Appendix
3. This notification has the effect of carrying out updates to the SCOMET list and defining the licensing jurisdiction for various categories of the SCOMET list.
Ajay Kumar Shalla Director General of Foreign Trade E-mail: dgft@nic.in [Issued from F.No.01/91/171/73/ AM 10/EC] Appendix 3 – SCOMET List
APPENDIX-3
Special Chemicals, Organisms, Materials, Equipment and Technologies (SCOMET) export of which is regulated
Export of Special Chemicals, Organisms, Materials, Equipment and Technologies (SCOMET) listed below shall be permitted only against an export authorisation issued in this behalf unless export is prohibited or is permitted without authorisation subject to fulfillment of conditions, if any, as indicated under/against any specific category or item. Provisions of Chapter IV A of the FT(D&R) Act,1992 as amended in 2010 shall apply to the goods, services and technologies as specified in the list below.
Supply of SCOMET Items from DTA to SEZ
No export authorisation is required for supply of SCOMET items from DTA to SEZ. However, all supplies of SCOMET items from DTA to SEZ will be reported to the Development Commissioner of the respective SEZ by the supplier in the prescribed proforma [Annexure 1 to Appendix-3 to Schedule 2 of ITC (HS) Classifications of Export and Import Items] within one week of the supplies getting effected.
An annual report of such supplies from DTA to SEZ shall be sent to SCOMET Section, DGFT (Hqrs), Department of Commerce, Udyog Bhawan, Maulana Azad Road, New Delhi-110011, by the Development Commissioner (DC), SEZ in the prescribed proforma [Annexure 2 to Appendix-3 to Schedule 2 of ITC
(HS) Classifications of Export and Import Items]. Report by the DC, SEZ is to be filed by 15th May of every financial year for the supplies effected during the preceding financial year.
Export of SCOMET Items from SEZ to outside the country
Export permission is required if the SCOMET items are to be physically exported outside the country from SEZ i.e. to another country (Refer Rule 26 of the SEZ Rules, 2006).
Entering into an Arrangement or Understanding for Site Visits, On-site Verification and Access to Records / Documentation
It is mandatory for all companies and their subsidiaries registered in India and all other business entities operating in India and involved in the manufacture, processing and use of Special Chemicals, Organisms, Materials, Equipment and Technologies (SCOMET) listed below to obtain permission of the DGFT before entering into any arrangement or understanding that involves an obligation to facilitate or undertake site visits, on-site verification or access to records/ documentation, by foreign Governments or foreign third parties, either acting directly or through an Indian party or parties. Requests for such permissions shall be considered in the manner in which requests for export/import licence are considered.
Provided that where obligations involving site visits, on-site verification or access to records/ documentation by foreign governments or foreign third parties are to be undertaken pursuant to a bilateral agreement or a multilateral treaty to which India is a party, the provisions of the relevant agreement or treaty shall apply.
Exporters are advised to refer to the relevant guidelines relating to the export of SCOMET items in the Handbook of Procedures, as issued from time to time. Para 2.78 of the Handbook of Procedures, 2015-2020 delineates the Procedure/Guidelines for filing / Evaluation of Applications for Entering into an Arrangement or Understanding for Site Visits, On-site Verification and Access to Records / Documentation.
Appendix 3 – SCOMET List
Items on the SCOMET List are organized in the following categories.
Category 0 Nuclear materials, nuclear-related other materials, equipment and technology 0A Prescribed Substances
0A1 Source Material
0A2 Special Fissionable Material
0A3 Other Materials
0B Prescribed Equipment
0C Technology
Category 1 Toxic chemical agents and other chemicals
1A Prohibited chemicals
1B Chemicals permitted only to States party to the Chemical Weapons Convention 1C Chemicals permitted also to States not party to the Chemical Weapons Convention 1D Other Chemicals
Category 2 Micro-organisms, toxins
2A Bacteria
2B Fungi
2C Parasites
2D Viruses
2E [Reserved]
2F Toxins
2G Plant pathogens
2H Genetically Modified Organisms
Category 3 Materials, Materials Processing Equipment and related technologies 3A Materials
3A1 Special materials
3A2 Structural materials
3A3 Rocket propellants and constituent chemicals
3A4 High explosives
3A5 Stealth materials
3B Materials processing and production equipment, related technology and specially designed components and accessories therefor.
3C [Reserved]
3D Chemical and biomaterial manufacturing and handling equipment and facilities Category 4 Nuclear-related other equipment and technology, not controlled under Category 0 4A Equipment, assemblies, components including test and production equipment 4B Equipment, assemblies, components including test and measurement equipment usable in development of nuclear explosive devices
4C Technology
Category 5 Aerospace systems, equipment, including production and test equipment, related technology and specially designed components and accessories therefore.
5A Rocket systems
5A1 Systems
5A2 Production and test equipment
5A3 Technology
5B Unmanned aerial vehicles
5C Avionics and navigation systems
Appendix 3 – SCOMET List
5D Manned-aircraft, aero-engines, related equipment and components 5E Micro-light aircraft and powered ‘hang-gliders’
Category 6 Munitions List
Category 7 Electronics, computers, and information technology including information security 7A Electronics
7B Electronic test equipment
7C [Reserved]
7D Information technology including information security 7E [Reserved]
Category 8 Special Materials and Related Equipment, Material Processing, Electronics, Computers, Telecommunications, Information Security, Sensors and Lasers, Navigation and Avionics, Marine, Aerospace and Propulsion
Appendix 3 – SCOMET List
COMMODITY IDENTIFICATION NOTE TO SCOMET
Note 1: If items are prima facie, classifiable under two or more headings, the heading which provides the most specific description shall be preferred to heading providing a more general description. The end-use of the item would be a relevant criteria in determining the classification.
Note 2: Notwithstanding anything contained in Note 1, the following items, will be classified under the relevant description in Category 0:
a) Radioactive materials covered under 6A007;
b) Any material containing Beryllium or “Zirconium with Hafnium content less than 2000 ppm” as the major constituent, or more than 60% Hafnium by weight, or “Boron enriched in Boron-10 isotope” or Niobium or tantalum covered under 6A008;
c) Nuclear power generating equipment or propulsion equipment, including "nuclear reactors", and specially designed for military use and components therefor specially designed or 'modified for military use’ covered under 6A017;
d) Simulators specially designed for military "nuclear reactors" covered under 6A017;
e) Any alloy with niobium as a major constituent in solid or powder form covered under 8C102;
f) Uranium-titanium alloys covered under 8C104;
g) Any material containing “Zirconium with Hafnium content less than 2000 ppm” or “Boron enriched in Boron- 10 isotope” as the major constituent covered under 8C111;
h) Plutonium and Neptunium covered under 8C112
Note 3: Items specified in Category 6A007.b which correspond to items specified in Category 1A are prohibited for exports.
Note 4: Licence applications for items in Categories 6A008 a.13 and 6A008.a 21, which correspond to items specified in 3A401.a, 3A401.b respectively, would normally be denied.
GENERAL NOTES
1. Terms in "quotations" are defined terms. Refer to ‘Glossary’ in SCOMET list.
2. In some instances chemicals are listed by name and CAS number. The list applies to chemicals of the same structural formula (including hydrates) regardless of name or CAS number. CAS numbers are shown to assist in identifying a particular chemical or mixture, irrespective of nomenclature. CAS numbers cannot be used as unique identifiers because some forms of the listed chemical have different CAS numbers, and mixtures containing a listed chemical may also have different CAS numbers.
3. The object of the controls contained in this Schedule should not be defeated by the export of any non-controlled goods containing one or more controlled components when the controlled component or components are the principal element of the goods and can feasibly be removed or used for other purposes. N.B.: In judging whether the controlled component or components are to be considered the principal element, it is necessary to weigh the factors of quantity, value and technological know-how involved and other special circumstances which might establish the controlled component or components as the principal element of the goods being procured.
4. Goods specified in this Schedule include both new and used goods.
GENERAL TECHNOLOGY NOTE
1. The export of "technology" which is "required" for the "development", "production" or "use" of items controlled in Category 8 is controlled according to the provisions in each sub-category. This "technology" remains under control even when applicable to any uncontrolled item.
2. Controls do not apply to that "technology" which is the minimum necessary for the installation, operation, maintenance (checking) or repair of those items which are not controlled or whose export has been authorised.
Appendix 3 – SCOMET List
Note: This does not release such "technology" controlled in entries 8E102.e. & 8E102.f. and 8E802.a. & 8E802.b.
3. Controls do not apply to "technology" "in the public domain", to "basic scientific research" or to the minimum necessary information for patent applications.
GENERAL SOFTWARE NOTE
The Lists do not control "software" which is any of the following:
1. Generally available to the public by being:
a. Sold from stock at retail selling points without restriction, by means of:
1. Over-the-counter transactions;
2. Mail order transactions;
3. Electronic transactions; or
4. Telephone call transactions; and
b. Designed for installation by the user without further substantial support by the supplier;
Note: Entry 1 of the General Software Note does not release "software" controlled by (8A5, 8B5, 8C5, 8D5,8E5)-Part-II (Information Security)
2. "In the public domain"; or
3. The minimum necessary "object code" for the installation, operation, maintenance (checking) or repair of those items whose export has been authorised.
Note: Entry 3 of the General Software Note does not release "software" controlled by (8A5, 8B5, 8C5, 8D5,8E5)-Part-II (Information Security).
GENERAL "INFORMATION SECURITY" NOTE
"Information security" items or functions should be considered against the provisions in (8A5, 8B5, 8C5, 8D5, 8E5)-Part-II (Information Security), even if they are components, "software" or functions of other items.
Appendix 3 – SCOMET List
GLOSSARY
Expressions used in the SCOMET List have the following meanings:
“Accuracy”: (Usually measured in terms of inaccuracy) is the maximum deviation, positive or negative, of an indicated value from an accepted standard or true value.
“Active flight control systems”: Function to prevent undesirable aircraft and missile motions or structural loads by autonomously processing outputs from multiple sensors and then providing necessary preventive commands to effect automatic control.
“Active pixel”: A minimum (single) element of the solid state array which has a photoelectric transfer function when exposed to light (electromagnetic) radiation.
“Additives”: Substances used in explosive formulations to improve their properties.
“Aircraft”: A fixed wing, swivel wing, rotary wing (helicopter), tilt rotor or tilt-wing airborne vehicle.
“Airship”: A power-driven airborne vehicle that is kept buoyant by a body of gas (usually helium, formerly hydrogen) which is lighter than air.
“All compensations available”: means after all feasible measures available to the manufacturer to minimise all systematic positioning errors for the particular machine-tool model or measuring errors for the particular coordinate measuring machine are considered.
“Allocated by the ITU”: The allocation of frequency bands according to the current edition of the ITU Radio Regulations for primary, permitted and secondary services.
N.B. Additional and alternative allocations are not included.
“Angle random walk”: The angular error build up with time that is due to white noise in angular rate. (IEEE STD 528- 2001)
“Angular position deviation”: The maximum difference between angular position and the actual, very accurately measured angular position after the work piece mount of the table has been turned out of its initial position.
“Asymmetric algorithm”: A cryptographic algorithm using different, mathematically-related keys for encryption and decryption.
Technical Note: A common use of asymmetric algorithms is key management.
“Authentication”: Verifying the identity of a user, process or device, often as a prerequisite to allowing access to resources in an information system. This includes verifying the origin or content of a message or other information, and all aspects of access control where there is no encryption of files or text except as directly related to the protection of passwords, Personal Identification Numbers (PINs) or similar data to prevent unauthorized access.
“Automated Command and Control Systems”: Electronic systems, through which information essential to the effective operation of the grouping, major formation, tactical formation, unit, ship, subunit or weapons under command is entered, processed and transmitted. This is achieved by the use of computer and other specialised hardware designed to support the functions of a military command and control organisation. The main functions of an automated command and control system are: the efficient automated collection, accumulation, storage and processing of information; the display of the situation and the circumstances affecting the preparation and conduct of combat operations; operational and tactical calculations for the allocation of resources among force groupings or elements of the operational order of battle or battle deployment according to the mission or stage of the operation; the preparation of data for appreciation of the situation and decision-making at any point during operation or battle; computer simulation of operations.
Appendix 3 – SCOMET List
“Automatic target tracking”: A processing technique that automatically determines and provides as output an extrapolated value of the most probable position of the target in real time.
“Average output power”: The total laser output energy, in joules, divided by the period over which a series of consecutive pulses is emitted, in seconds. For a series of uniformly-spaced pulses it is equal to the total laser output energy in a single pulse, in joules, multiplied by the pulse frequency of the laser, in Hertz.
“Basic gate propagation delay time”: The propagation delay time value corresponding to the basic gate used in a monolithic integrated circuit. For a 'family' of monolithic integrated circuits, this may be specified either as the propagation delay time per typical gate within the given 'family' or as the typical propagation delay time per gate within the given 'family'.
Technical Notes:
1. Basic gate propagation delay time is not to be confused with the input/output delay time of a complex monolithic integrated circuit.
2. 'Family' consists of all integrated circuits to which all of the following are applied as their manufacturing methodology and specifications except their respective functions:
a. The common hardware and software architecture;
b. The common design and process technology; and
c. The common basic characteristics.
“Basic scientific research”: Experimental or theoretical work undertaken principally to acquire new knowledge of the fundamental principles of phenomena or observable facts, not primarily directed towards a specific practical aim or objective.
“Bias (accelerometer)”: The average over a specified time of accelerometer output, measured at specified operating conditions that has no correlation with input acceleration or rotation. Bias is expressed in g or in metres per second2 (g or m/s2). (IEEE Std 528-2001) (Micro g equals 1x10-6 g).
“Bias (gyro)”: The average over a specified time of gyro output measured at specified operating conditions that have no correlation with input rotation or acceleration. Bias is typically expressed in degrees per hour (deg/hr). (IEEE Std 528- 2001).
“Biocatalysts”: 'Enzymes' for specific chemical or biochemical reactions or other biological compounds which bind to and accelerate the degradation of CW agents.
Technical Note: 'Enzymes' means biocatalysts for specific chemical or biochemical reactions.
“Biological agents”: Pathogens or toxins, selected or modified (such as altering purity, shelf life, virulence, dissemination characteristics, or resistance to UV radiation) to produce casualties in humans or animals, degrade equipment or damage crops or the environment.
“Biopolymers”: Biological macromolecules as follows:
a. Enzymes for specific chemical or biochemical reactions;
b. 'Anti-idiotypic', 'monoclonal' or 'polyclonal' 'antibodies';
c. Specially designed or specially processed 'receptors'
Technical Notes:
1. 'Anti-idiotypic antibodies' means antibodies which bind to the specific antigen binding sites of other antibodies;
2. 'Monoclonal antibodies' means proteins which bind to one antigenic site and are produced by a single clone of cells;
Appendix 3 – SCOMET List
3. 'Polyclonal antibodies' means a mixture of proteins which bind to the specific antigen and are produced by more than one clone of cells;
4. 'Receptors' means biological macromolecular structures capable of binding ligands, the binding of which affects physiological functions.
“Camming (axial displacement)”: Axial displacement in one revolution of the main spindle measured in a plane perpendicular to the spindle faceplate, at a point next to the circumference of the spindle faceplate (Reference: ISO 230/1 1986, paragraph 5.63 as applicable).
“Carbon fibre performs”: An ordered arrangement of uncoated or coated fibres intended to constitute a framework of a part before the matrix is introduced to form a composite.
“Chemical Laser”: A laser in which the excited species is produced by the output energy from a chemical reaction.
“Circuit element”: A single active or passive functional part of an electronic circuit, such as one diode, one transistor, one resistor, one capacitor, etc.
“Circular Error Probable (CEP)”: in a circular normal distribution, the radius of the circle containing 50% of the individual measurements being made, or the radius of the circle within which there is a 50% probability of being located.
“Circulation-controlled anti-torque or circulation-controlled direction control systems”: Control systems using air blown over aerodynamic surfaces to increase or control the forces generated by the surfaces.
“Civil aircraft”: Those aircraft listed by designation in published airworthiness certification lists by the competent civil aviation authorities to fly commercial civil internal and external routes or for legitimate civil, private or business use.
“Commingled”: Filament to filament blending of thermoplastic fibres and reinforcement fibres in order to produce a fibre reinforcement matrix mix in total fibre form.
“Comminution”: A process to reduce a material to particles by crushing or grinding.
“Communications channel controller”: The physical interface which controls the flow of synchronous or asynchronous digital information. It is an assembly that can be integrated into computer or telecommunications equipment to provide communications access.
“Compensation systems”: consist of the primary scalar sensor, one or more reference sensors (e.g. vector magnetometers) together with software that permit reduction of rigid body rotation noise of the platform.
“Composite”: A matrix and an additional phase or additional phases consisting of particles, whiskers, fibres or any combination thereof, present for a specific purpose or purposes.
“Composite theoretical performance (CTP)”: A measure of computational performance given in millions of theoretical operations per second (Mtops).
“Compound rotary table”: A table allowing the workpiece to rotate and tilt about two non-parallel axes, which can be coordinated simultaneously for contouring control.
“III/V compounds”: Polycrystalline or binary or complex monocrystalline products consisting of elements of groups IIIA and VA of Mendeleyev's periodic classification table (e.g., gallium arsenide, gallium-aluminium arsenide, indium phosphide).
“Contouring control”: Two or more numerically controlled motions operating in accordance with instructions that specify the next required position and the required feed rates to that position. These feed rates are varied in relation to each other so that a desired contour is generated (Ref. ISO/DIS 2806 – 1980 as applicable).
“Critical temperature”: (sometimes referred to as the transition temperature) of a specific superconductive material is the temperature at which the material loses all resistance to the flow of direct electrical current.
Appendix 3 – SCOMET List
“Cryptographic activation”: Any technique that activates or enables cryptographic capability of an item, by means of a secure mechanism implemented by the manufacturer of the item, where this mechanism is uniquely bound to any of the following:
1. A single instance of the item; or
2. One customer, for multiple instances of the item.
Technical Notes:
1. ″Cryptographic activation″ techniques and mechanisms may be implemented as hardware, ″software″ or ″technology″.
2. Mechanisms for cryptographic activation can, for example, be serial number-based licence keys or authentication instruments such as digitally signed certificates.
“Cryptography”: The discipline which embodies principles, means and methods for the transformation of data in order to hide its information content, prevent its undetected modification or prevent its unauthorized use. Cryptography is limited to the transformation of information using one or more 'secret parameters' (e.g., crypto variables) or associated key management.
Note: Cryptography does not include 'fixed' data compression or coding techniques.
Technical Notes:
1. 'Secret parameter': a constant or key kept from the knowledge of others or shared only within a group.
2. 'Fixed': the coding or compression algorithm cannot accept externally supplied parameters (e.g., cryptographic or key variables) and cannot be modified by the user.
“CTP”: is equivalent to composite theoretical performance.
“CW Laser”: A laser that produces nominally constant output energy for greater than 0.25 seconds.
“Data-Based Referenced Navigation (DBRN) Systems”: Systems which use various sources of previously measured geo-mapping data integrated to provide accurate navigation information under dynamic conditions. Data sources include bathymetric maps, stellar maps, gravity maps, magnetic maps or 3-D digital terrain maps.
“Deactivated firearm”: A firearm that has undergone ‘deactivation’ as defined in the Arms Rules 2016.
“Deformable Mirrors”: Mirrors
a. Having a single continuous optical reflecting surface which is dynamically deformed by the application of individual torques or forces to compensate for distortions in the optical waveform incident upon the mirror; or
b. Having multiple optical reflecting elements that can be individually and dynamically repositioned by the application of torques or forces to compensate for distortions in the optical waveform incident upon the mirror.
Deformable mirrors are also known as adaptive optic mirrors.
“Designed or modified”: describes equipment, parts or components which, as a result of development, or modification, have become endowed with specified properties that make them fit for a particular application.
“Development”: is related to all stages prior to serial production, such as: design, design research, design analyses, design concepts, assembly and testing of prototypes, pilot production schemes, design data, process of transforming design data into a product, configuration design, integration design, layouts.
“Diffusion bonding”: A solid state joining of at least two separate pieces of metals into a single piece with a joint strength equivalent to that of the weakest material, wherein the principal mechanism is interdiffusion of atoms across the interface.
Appendix 3 – SCOMET List
“Digital computer”: Equipment which can, in the form of one or more discrete variables, perform all of the following:
a. Accept data;
b. Store data or instructions in fixed or alterable (writable) storage devices;
c. Process data by means of a stored sequence of instructions which is modifiable; and
d. Provide output of data.
Technical Note: Modifications of a stored sequence of instructions include replacement of fixed storage devices, but not a physical change in wiring or interconnections.
“Digital transfer rate”: The total bit rate of the information that is directly transferred on any type of medium. (See also total digital transfer rate).
“Direct-acting hydraulic pressing”: A deformation process which uses a fluid-filled flexible bladder in direct contact with the workpiece.
“Discrete component”: A separately packaged circuit element with its own external connections.
“Effective gram”: Effective gram for plutonium isotope is defined as the isotope weight in grams.
“Electronically steerable phased array antenna”: An antenna which forms a beam by means of phase coupling, (i.e., the beam direction is controlled by the complex excitation coefficients of the radiating elements) and the direction of that beam can be varied (both in transmission and reception) in azimuth or in elevation, or both, by application of an electrical signal.
“Electronic assembly”: A number of electronic components (i.e., circuit elements, discrete components, integrated circuits, etc.) connected together to perform (a) specific function(s), replaceable as an entity and normally capable of being disassembled.
“End-effectors”: Grippers, 'active tooling units' and any other tooling that is attached to the baseplate on the end of a robot manipulator arm.
Technical Note: 'Active tooling units' are devices for applying motive power, process energy or sensing to a workpiece.
“Energetic materials”: Substances or mixtures that react chemically to release energy required for their intended application. Explosives, pyrotechnics and propellants are subclasses of energetic materials.
“Equivalent Density”: The mass of an optic per unit optical area projected onto the optical surface.
“Explosives”: Solid, liquid or gaseous substances or mixtures of substances which, in their application as primary, booster, or main charges in warheads, demolition and other applications, are required to detonate.
“Expression Vectors”: Carriers (e.g., plasmid or virus) used to introduce genetic material into host cells.
“FADEC Systems”: Full Authority Digital Engine Control Systems – A digital electronic control system for a gas turbine engine that is able to autonomously control the engine throughout its whole operating range from demanded engine start until demanded engine shut-down, in both normal and fault conditions.
“Fibrous or filamentary materials”: include
a. Continuous monofilaments;
b. Continuous yarns and rovings;
c. Tapes, fabrics, random mats and braids;
d. Chopped fibres, staple fibres and coherent fibre blankets;
e. Whiskers, either monocrystalline or polycrystalline, of any length;
f. Aromatic polyamide pulp.
Appendix 3 – SCOMET List
“Film type integrated circuit”: An array of circuit elements and metallic interconnections formed by deposition of a thick or thin film on an insulating substrate.
“First generation image intensifier tubes”: Electrostatically focused tubes, employing input and output fibre optic or glass face plates, multi-alkali photocathodes (S-20 or S-25), but not microchannel plate amplifiers.
“Flight control optical sensor array”: A network of distributed optical sensors, using laser beams, to provide real-time flight control data for on-board processing.
“Flight path optimization”: A procedure that minimizes deviations from a four-dimensional (space and time) desired trajectory based on maximizing performance or effectiveness for mission tasks.
“Fly-by-light system”: A primary digital flight control system employing feedback to control the aircraft during flight, where the commands to the effectors/actuators are optical signals.
“Fly-by-wire system”: A primary digital flight control system employing feedback to control the aircraft during flight, where the commands to the effectors/actuators are electrical signals.
“Focal plane array”: A linear or two-dimensional planar layer, or combination of planar layers, of individual detector elements, with or without readout electronics, which work in the focal plane.
Note: This definition does not include a stack of single detector elements or any two, three or four element detectors provided time delay and integration is not performed within the element.
“Fractional bandwidth”: The instantaneous bandwidth divided by the centre frequency, expressed as a percentage.
“Frequency hopping”: A form of spread spectrum in which the transmission frequency of a single communication channel is made to change by a random or pseudo-random sequence of discrete steps.
“Frequency mask trigger”: For signal analysers a mechanism where the trigger function is able to select a frequency range to be triggered on as a subset of the acquisition bandwidth while ignoring other signals that may also be present within the same acquisition bandwidth. A frequency mask trigger may contain more than one independent set of limits.
“Frequency switching time”: The time (i.e., delay) taken by a signal when switched from an initial specified output frequency, to arrive at or within any of the following:
a. ±100 Hz of a final specified output frequency of less than 1 GHz; or
b. ±0.1 part per million of a final specified output frequency equal to or greater than 1 GHz.
“Frequency synthesizer”: Any kind of frequency source, regardless of the actual technique used, providing a multiplicity of simultaneous or alternative output frequencies, from one or more outputs, controlled by, derived from or disciplined by a lesser number of standard (or master) frequencies.
“Fuel cell”: An electrochemical device that converts chemical energy directly into Direct Current (DC) electricity by consuming fuel from an external source.
“Fusible”: Capable of being cross-linked or polymerized further (cured) by the use of heat, radiation, catalysts, etc., or that can be melted without pyrolysis (charring).
“Gas atomization”: A process to reduce a molten stream of metal alloy to droplets of 500 µm diameter or less by a high pressure gas stream.
“Geographically dispersed”: Sensors are considered geographically dispersed when each location is distant from any other more than 1,500 m in any direction. Mobile sensors are always considered geographically dispersed.
Appendix 3 – SCOMET List
“Hot isostatic densification”: A process of pressurising a casting at temperatures exceeding 375 K (102°C) in a closed cavity through various media (gas, liquid, solid particles, etc.) to create equal force in all directions to reduce or eliminate internal voids in the casting.
“Hybrid computer”: Equipment which can perform all of the following:
a. Accept data;
b. Process data, in both analogue and digital representations; and
c. Provide output of data.
“Hybrid integrated circuit”: Any combination of integrated circuit(s), or integrated circuit with circuit elements or discrete components connected together to perform (a) specific function(s), and having all of the following characteristics:
a. Containing at least one unencapsulated device;
b. Connected together using typical IC production methods;
c. Replaceable as an entity; and
d. Not normally capable of being disassembled.
“Image enhancement”: The processing of externally derived information-bearing images by algorithms such as time compression, filtering, extraction, selection, correlation, convolution or transformations between domains (e.g., fast Fourier transform or Walsh transform). This does not include algorithms using only linear or rotational transformation of a single image, such as translation, feature extraction, registration or false coloration.
“Information security”: All the means and functions ensuring the accessibility, confidentiality or integrity of information or communications, excluding the means and functions intended to safeguard against malfunctions. This includes cryptography, cryptographic activation, 'cryptanalysis', protection against compromising emanations and computer security.
Technical Note: 'Cryptanalysis': the analysis of a cryptographic system or its inputs and outputs to derive confidential variables or sensitive data, including clear text. (ISO 7498-2-1988 (E), paragraph 3.3.18 as applicable).
“Instantaneous bandwidth”: The bandwidth over which output power remains constant within 3 dB without adjustment of other operating parameters.
“Instrumented range”: The specified unambiguous display range of a radar.
“Insulation”: is applied to the components of a rocket motor, i.e. the case, nozzle, inlets, case closures, and includes cured or semi-cured compounded rubber sheet stock containing an insulating or refractory material. It may also be incorporated as stress relief boots or flaps.
“Interior lining”: is suited for the bond interface between the solid propellant and the case or insulating liner. Usually a liquid polymer based dispersion of refractory or insulating materials, e.g. carbon filled hydroxyl terminated polybutadiene (HTPB) or other polymer with added curing agents sprayed or screeded over a case interior.
“Intrinsic magnetic gradiometer”: A single magnetic field gradient sensing element and associated electronics the output of which is a measure of magnetic field gradient.
“Intrusion software”: Software specially designed or modified to avoid detection by 'monitoring tools', or to defeat 'protective countermeasures', of a computer or network-capable device, and performing any of the following:
a. The extraction of data or information, from a computer or network-capable device, or the modification of system or user data; or
b. The modification of the standard execution path of a program or process in order to allow the execution of externally provided instructions.
Appendix 3 – SCOMET List
Notes:
1. Intrusion software does not include any of the following:
a. Hypervisors, debuggers or Software Reverse Engineering (SRE) tools;
b. Digital Rights Management (DRM) software; or
c. Software designed to be installed by manufacturers, administrators or users, for the purposes of asset tracking or recovery.
2. Network-capable devices include mobile devices and smart meters.
Technical Notes:
1. 'Monitoring tools': software or hardware devices, that monitor system behaviours or processes running on a device. This includes antivirus (AV) products, end point security products, Personal Security Products (PSP), Intrusion Detection Systems (IDS), Intrusion Prevention Systems (IPS) or firewalls.
2. 'Protective countermeasures': techniques designed to ensure the safe execution of code, such as Data Execution Prevention (DEP), Address Space Layout Randomisation (ASLR) or sandboxing.
“Isolated live cultures”: includes live cultures in dormant form and in dried preparations.
“Isostatic presses”: Equipment capable of pressurising a closed cavity through various media (gas, liquid, solid particles, etc.) to create equal pressure in all directions within the cavity upon a workpiece or material.
“Laser”: An item that produces spatially and temporally coherent light through amplification by stimulated emission of radiation.
“Library (parametric technical database)”: A collection of technical information, reference to which may enhance the performance of relevant systems, equipment or components.
“Lighter-than-air vehicles”: Balloons and airships that rely on hot air or on lighter-than-air gases such as helium or hydrogen for their lift.
“Linearity (Usually measured in terms of non-linearity)”: is the maximum deviation of the actual characteristic (average of upscale and downscale readings), positive or negative, from a straight line so positioned as to equalise and minimise the maximum deviations.
“Local area network”: A data communication system having all of the following characteristics:
a. Allows an arbitrary number of independent 'data devices' to communicate directly with each other; and
b. Is confined to a geographical area of moderate size (e.g., office building, plant, campus, warehouse). Technical Note: 'Data device' means equipment capable of transmitting or receiving sequences of digital information.
“Magnetic gradiometers”: Are designed to detect the spatial variation of magnetic fields from sources external to the instrument. They consist of multiple magnetometers and associated electronics the output of which is a measure of magnetic field gradient. (See also Intrinsic Magnetic Gradiometer)
“Magnetometers”: Are designed to detect magnetic fields from sources external to the instrument. They consist of a single magnetic field sensing element and associated electronics the output of which is a measure of the magnetic field.
“Main storage”: The primary storage for data or instructions for rapid access by a central processing unit. It consists of the internal storage of a digital computer and any hierarchical extension thereto, such as cache storage or nonsequentially accessed extended storage.
“Matrix”: A substantially continuous phase that fills the space between particles, whiskers or fibres.
Appendix 3 – SCOMET List
“Measurement uncertainty”: The characteristic parameter which specifies in what range around the output value the correct value of the measurable variable lies with a confidence level of 95%. It includes the uncorrected systematic deviations, the uncorrected backlash and the random deviations (Reference: ISO 10360-2 as applicable).
“Mechanical alloying”: An alloying process resulting from the bonding, fracturing and rebonding of elemental and master alloy powders by mechanical impact. Non-metallic particles may be incorporated in the alloy by addition of the appropriate powders.
“Melt extraction”: A process to solidify rapidly and extract a ribbon-like alloy product by the insertion of a short segment of a rotating chilled block into a bath of a molten metal alloy.
“Melt spinning”: A process to solidify rapidly a molten metal stream impinging upon a rotating chilled block, forming a flake, ribbon or rod-like product.
“Microcircuit”: A device in which a number of passive and/or active elements are considered as indivisibly associated on or within a continuous structure to perform the function of a circuit “Microcomputer microcircuit”: A monolithic integrated circuit or multichip integrated circuit containing an arithmetic logic unit (ALU) capable of executing general purpose instructions from an internal storage, on data contained in the internal storage.
Technical Note: The internal storage may be augmented by an external storage.
“Microprocessor microcircuit”: A monolithic integrated circuit or multichip integrated circuit containing an arithmetic logic unit (ALU) capable of executing a series of general purpose instructions from an external storage.
Technical Note: The microprocessor microcircuit normally does not contain integral user-accessible storage, although storage present on-the-chip may be used in performing its logic function.
Note: This definition includes chip sets which are designed to operate together to provide the function of a microprocessor microcircuit.
“Microprogram”: A sequence of elementary instructions maintained in a special storage, the execution of which is initiated by the introduction of its reference instruction into an instruction register.
“Monolithic Microwave Integrated Circuit (MMIC)”: A monolithic integrated circuit that operates at microwave or millimeter wave frequencies.
“Missiles”: means complete rocket systems and unmanned aerial vehicle systems.
“Modified in the context of software”: describes software which has been intentionally changed such that it has properties that make it fit for specified purposes or applications. Its properties may also make it suitable for purposes or applications other than those for which it was modified.
“Monofilament or filament”: is the smallest increment of fibre, usually several micrometres in diameter.
“Monolithic integrated circuit”: A combination of passive or active circuit elements or both which:
a. Are formed by means of diffusion processes, implantation processes or deposition processes in or on a single semiconducting piece of material, a so-called 'chip';
b. Can be considered as indivisibly associated; and
c. Perform the function(s) of a circuit.
Technical Note: ‘Circuit element’ is a single active or passive functional part of an electronic circuit, such as one diode, one transistor, one resistor, one capacitor, etc.
“Monospectral imaging”: sensors are capable of acquisition of imaging data from one discrete spectral band.
“Multichip integrated circuit”: Two or more monolithic integrated circuits bonded to a common substrate.
Appendix 3 – SCOMET List
“Multispectral imaging sensors”: are capable of simultaneous or serial acquisition of imaging data from two or more discrete spectral bands. Sensors having more than twenty discrete spectral bands are sometimes referred to as hyperspectral imaging sensors.
“Network access controller”: A physical interface to a distributed switching network. It uses a common medium which operates throughout at the same digital transfer rate using arbitration (e.g., token or carrier sense) for transmission. Independently from any other, it selects data packets or data groups (e.g., IEEE 802) addressed to it. It is an assembly that can be integrated into computer or telecommunications equipment to provide communications access.
“Neural computer”: A computational device designed or modified to mimic the behaviour of a neuron or a collection of neurons, i.e., a computational device which is distinguished by its hardware capability to modulate the weights and numbers of the interconnections of a multiplicity of computational components based on previous data.
“Nuclear reactor”: includes the items within or attached directly to the reactor vessel, the equipment which controls the level of power in the core, and the components which normally contain or come into direct contact with or control the primary coolant of the reactor core.
“Numerical control “:The automatic control of a process performed by a device that makes use of numeric data usually introduced as the operation is in progress (Ref. ISO 2382 as applicable).
“Object code”: An equipment executable form of a convenient expression of one or more processes (source code (or source language)) which has been compiled by a programming system.
“Operations, Administration or Maintenance (OAM)”: Means performing one or more of the following tasks:
a. Establishing or managing any of the following:
1. Accounts or privileges of users or administrators;
2. Settings of an item; or
3. Authentication data in support of the tasks described in a.1. or a.2 above.;
b. Monitoring or managing the operating condition or performance of an item; or
c. Managing logs or audit data in support of any of the tasks described in a. or b above.
Note: OAM does not include any of the following tasks or their associated key management functions:
a. Provisioning or upgrading any cryptographic functionality that is not directly related to establishing or managing authentication data in support of the tasks described in a.1. or a.2. above; or
b. Performing any cryptographic functionality on the forwarding or data plane of an item.
“Optical computer”: A computer designed or modified to use light to represent data and whose computational logic elements are based on directly coupled optical devices.
“Optical integrated circuit”: A monolithic integrated circuit or a hybrid integrated circuit, containing one or more parts designed to function as a photosensor or photoemitter or to perform (an) optical or (an) electro-optical function(s).
“Optical switching”: The routing of or switching of signals in optical form without conversion to electrical signals.
“Overall current density”: The total number of ampere-turns in the coil (i.e., the sum of the number of turns multiplied by the maximum current carried by each turn) divided by the total cross-section of the coil (comprising the superconducting filaments, the metallic matrix in which the superconducting filaments are embedded, the encapsulating material, any cooling channels, etc.).
“Peak power”: The highest power attained in the pulse duration.
“Personal area network”: A data communication system having all of the following characteristics:
a. Allows an arbitrary number of independent or interconnected 'data devices' to communicate directly with each other; and
Appendix 3 – SCOMET List
b. Is confined to the communication between devices within the immediate vicinity of an individual person or device controller (e.g., single room, office, or automobile, and their nearby surrounding spaces). Technical Note: 'Data device' means equipment capable of transmitting or receiving sequences of digital information.
“Plasma atomization”: A process to reduce a molten stream or solid metal to droplets of 500 µm diameter or less, using plasma torches in an inert gas environment.
“Power management”: Changing the transmitted power of the altimeter signal so that received power at the aircraft altitude is always at the minimum necessary to determine the altitude.
“Precursors”: Speciality chemicals used in the manufacture of explosives.
“Pressure transducers”: are devices that convert pressure measurements into an electrical signal.
“Previously separated”: The application of any process intended to increase the concentration of the controlled isotope.
“Primary flight control”: Aircraft stability or manoeuvering control using force/moment generators, i.e. aerodynamic control surfaces or propulsive thrust vectoring.
“Principal element”: An element is a principal element when its replacement value is more than 35% of the total value of the system of which it is an element. Element value is the price paid for the element by the manufacturer of the system, or by the system integrator. Total value is the normal international selling price to unrelated parties at the point of manufacture or consolidation of shipment.
“Production”: Means all production stages, such as: product engineering, manufacture, integration, assembly (mounting), inspection, testing, quality assurance.
“Production equipment”: Tooling, templates, jigs, mandrels, moulds, dies, fixtures, alignment mechanisms, test equipment, other machinery and components therefor, limited to those specially designed or modified for development or for one or more phases of production.
“Production facilities”: Equipment and specially designed software therefor integrated into installations for development or for one or more phases of production.
“Program”: A sequence of instructions to carry out a process in, or convertible into, a form executable by an electronic computer.
“Propellants”: Substances or mixtures that react chemically to produce large volumes of hot gases at controlled rates to perform mechanical work.
“Public domain”: means a domain that has no restrictions upon dissemination of information within or from it; the existence of any legal rights to the intellectual property in that information does not remove the information from being in public domain.
Note: Copyright restrictions do not remove technology or software from being in the public domain.
“Pulse compression”: The coding and processing of a radar signal pulse of long time duration to one of short time duration, while maintaining the benefits of high pulse energy.
“Pulse duration”: Duration of a laser pulse is the time between the half-power points on the leading edge and trailing edge of an individual pulse.
“Pulsed laser”: A laser having a pulse duration that is less than or equal to 0.25 seconds.
“Pyrotechnic(s)”: Mixtures of solid or liquid fuels and oxidizers which, when ignited, undergo an energetic chemical reaction at a controlled rate intended to produce specific time delays, or quantities of heat, noise, smoke, visible light or
Appendix 3 – SCOMET List
infrared radiation. Pyrophorics are a subclass of pyrotechnics, which contain no oxidizers but ignite spontaneously on contact with air.
“Quantum cryptography”: A family of techniques for the establishment of a shared key for cryptography by measuring the quantum-mechanical properties of a physical system (including those physical properties explicitly governed by quantum optics, quantum field theory, or quantum electrodynamics).
“Radar frequency agility”: Any technique which changes, in a pseudo-random sequence, the carrier frequency of a pulsed radar transmitter between pulses or between groups of pulses by an amount equal to or larger than the pulse bandwidth.
“Radar spread spectrum”: Any modulation technique for spreading energy originating from a signal with a relatively narrow frequency band, over a much wider band of frequencies, by using random or pseudo-random coding.
“Radiant sensitivity”: Radiant sensitivity (mA/W) = 0.807 x (wavelength in nm) x Quantum Efficiency (QE)
Technical Note: QE is usually expressed as a percentage; however, for the purposes of this formula QE is expressed as a decimal number less than one, e.g., 78% is 0.78.
“Radiation hardened”: means that the component or equipment is designed or rated to withstand radiation levels which meet or exceed a total radiation dose of 5 x 103 Gy or 5 x 105 rads (Si).
“Real-time bandwidth”: For signal analysers, the widest frequency range for which the analyser can continuously transform time-domain data entirely into frequency-domain results using a Fourier or other discrete time transform that processes every incoming time point, without a reduction of measured amplitude of more than 3 dB below the actual signal amplitude caused by gaps or windowing effects, while outputting or displaying the transformed data.
“Real-time processing”: The processing of data by a computer system providing a required level of service, as a function of available resources, within a guaranteed response time, regardless of the load of the system, when stimulated by an external event.
“Repeatability”: The closeness of agreement among repeated measurements of the same variable under the same operating conditions when changes in conditions or non-operating periods occur between measurements. (Reference: IEEE STD 528-2001 (one sigma standard deviation)
“Required”: As applied to technology, refers to only that portion of technology which is peculiarly responsible for achieving or exceeding the controlled performance levels, characteristics or functions. Such required technology may be shared by different products.
“Resolution”: he least increment of a measuring device; on digital instruments, the least significant bit. (Reference:
ANSI B-89.1.12)
“Riot control agents”: Substances which, under the expected conditions of use for riot control purposes produce rapidly in humans sensory irritation or disabling physical effects which disappear within a short time following termination of exposure. (Tear gases are a subset of riot control agents)
“Robot”: A manipulation mechanism, which may be of the continuous path or of the point-to-point variety, may use sensors, and has all the following characteristics:
a) Is multifunctional;
b) Is capable of positioning or orienting material, parts, tools or special devices through variable movements in three dimensional space;
c) Incorporates three or more closed or open loop servo-devices which may include stepping motors; and
d) Has user-accessible programmability by means of the teach/playback method or by means of an electronic computer which may be a programmable logic controller, i.e., without mechanical intervention.
Note: The above definition does not include the following devices:
Appendix 3 – SCOMET List
1. Manipulation mechanisms which are only manually/tele-operator controllable;
2. Fixed sequence manipulation mechanisms which are automated moving devices, operating according to mechanically fixed programmed motions. The programme is mechanically limited by fixed stops, such as pins or cams. The sequence of motions and the selection of paths or angles are not variable or changeable by mechanical, electronic or electrical means;
3. Mechanically controlled variable sequence manipulation mechanisms which are automated moving devices, operating according to mechanically fixed programmed motions. The programme is mechanically limited by fixed, but adjustable stops, such as pins or cams. The sequence of motions and the selection of paths or angles are variable within the fixed programme pattern. Variations or modifications of the programme pattern (e.g., changes of pins or exchanges of cams) in one or more motion axes are accomplished only through mechanical operations;
4. Non-servo-controlled variable sequence manipulation mechanisms which are automated moving devices, operating according to mechanically fixed programmed motions. The programme is variable but the sequence proceeds only by the binary signal from mechanically fixed electrical binary devices or adjustable stops;
5. Stacker cranes defined as Cartesian coordinate manipulator systems manufactured as an integral part of a vertical array of storage bins and designed to access the contents of those bins for storage or retrieval. “Rotary atomization”: A process to reduce a stream or pool of molten metal to droplets to a diameter of 500 µm or less by centrifugal force.
“Roving”: is a bundle (typically 12-120) of approximately parallel ‘strands’.
N.B.: ‘Strand’ is a bundle of monofilaments (typically over 200) arranged approximately parallel.
“Run-out (out-of-true running)”: Radial displacement in one revolution of the main spindle measured in a plane perpendicular to the spindle axis at a point on the external or internal revolving surface to be tested (Reference: ISO 230/1-1986, paragraph 5.61 as applicable).
“Scale factor (gyro or accelerometer)”: The ratio of change in output to a change in the input intended to be measured. Scale factor is generally evaluated as the slope of the straight line that can be fitted by the method of least squares to input-output data obtained by varying the input cyclically over the input range.
“Settling time”: The time required for the output to come within one-half bit of the final value when switching between any two levels of the converter.
“Signal analysers”: Apparatus capable of measuring and displaying basic properties of the single-frequency components of multi-frequency signals.
“Signal processing”: The processing of externally derived information-bearing signals by algorithms such as time compression, filtering, extraction, selection, correlation, convolution or transformations between domains (e.g., fast Fourier transform or Walsh transform).
“Software”: A collection of one or more programs, or micro-programs, fixed in any tangible medium of expression. However, unless otherwise provided for against any item on the SCOMET List, the List does not control software which is either in the public domain or is generally available to the public by being:
a. Sold from stock at retail selling points without restriction, by means of:
1. Over-the-counter transactions;
2. Mail order transactions;
3. Electronic transactions; or
4. Telephone call transactions; and
b. Designed for installation by the user without further substantial support by the supplier.
“Solidify rapidly”: A process involving the solidification of molten material at cooling rates exceeding 1 000 K/sec.
Appendix 3 – SCOMET List
“Source code”: A convenient expression of one or more processes which may be turned by a programming system into equipment executable form (object code (or object language).
“Spacecraft” : Active and passive satellites and space probes
“Spacecraft bus”: Equipment that provides the support infrastructure of the spacecraft and location for the spacecraft payload.
“Spacecraft payload”: Equipment, attached to the spacecraft bus, designed to perform a mission in space (e.g., communications, observation, science).
“Space-qualified”: Designed, manufactured, or qualified through successful testing, for operation at altitudes greater than 100 km above the surface of the Earth.
Note: A determination that a specific item is space- qualified by virtue of testing does not mean that other items in the same production run or model series are space-qualified if not individually tested.
“Space qualified”: Products designed, manufactured and tested to meet the special electrical, mechanical or environmental requirements for use in the launch and deployment of satellites or high altitude flight systems operating at altitudes of 100 km or higher.
Note: A determination that a specific item is space- qualified by virtue of testing does not mean that other items in the same production run or model series are space-qualified if not individually tested.
“Specially designed”: qualifies the description of equipment, parts, components or software which, as a result of development, have unique properties that distinguish them for certain predetermined purposes. For example, a piece of equipment that is specially designed will only be considered so if it has no other function or use. Thus a piece of manufacturing equipment that is specially designed to produce a certain type of component will only be considered such if it is not capable of producing other types of components.
“Specific modulus”: Young's modulus in pascals, equivalent to N/m2, divided by specific weight in N/m3, measured at a temperature of 296 ± 2 K (23 ± 2°C) and a relative humidity of (50 ± 5)%.
“Specific tensile strength”: Ultimate tensile strength in pascals, equivalent to N/m2, divided by specific weight in N/m3, measured at a temperature of 296 ± 2 K (23 ± 2°C) and a relative humidity of (50 ± 5)%.
“Spinning mass gyros”: Spinning mass gyros are gyros which use a continually rotating mass to sense angular motion.
“Splat quenching”: A process to solidify rapidly a molten metal stream impinging upon a chilled block, forming a flakelike product.
“Spread spectrum”: The technique whereby energy in a relatively narrow-band communication channel is spread over a much wider energy spectrum.
“Spread spectrum radar”: see Radar spread spectrum
“Stability”: Standard deviation (1 sigma) of the variation of a particular parameter from its calibrated value measured under stable temperature conditions. This can be expressed as a function of time.
Explanation: For gyroscopes, stability can be estimated by determining the Allan variance noise-analysis value at the integration period (i.e., sample time) consistent with the stated measurement period, which may include extrapolating the Allan variance noise analysis beyond the instability point into the rate random walk or rate ramp regions to an integration period consistent with the stated measurement period (Reference: IEEE Std 952-1997 [R2008]). Allan variance noise analysis is often used to characterize MicroElectroMechanical Systems (MEMS) gyroscopes, and is applicable to other gyroscopes, such as Ring Laser Gyroscopes (RLGs) and Fibre Optic Gyroscopes (FOGs).
Appendix 3 – SCOMET List
“Substrate”: A sheet of base material with or without an interconnection pattern and on which or within which discrete components or integrated circuits or both can be located.
“Substrate blanks”: Monolithic compounds with dimensions suitable for the production of optical elements such as mirrors or optical windows.
“Superalloy”: Nickel-, cobalt- or iron-base alloys having strengths superior to any alloys in the AISI 300 series at temperatures over 922 K (649°C) under severe environmental and operating conditions.
“Superconductive”: Refers to materials,(i.e., metals, alloys or compounds) which can lose all electrical resistance (i.e., which can attain infinite electrical conductivity and carry very large electrical currents without Joule heating).
Technical Note: The superconductive state of a material is individually characterised by a critical temperature, a critical magnetic field, which is a function of temperature, and a critical current density which is, however, a function of both magnetic field and temperature.
“Super High Power Laser (SHPL)”: A laser capable of delivering (the total or any portion of) the output energy exceeding 1 kJ within 50 ms or having an average or CW power exceeding 20 Kw “Superplastic forming”: A deformation process using heat for metals that are normally characterised by low values of elongation (less than 20%) at the breaking point as determined at room temperature by conventional tensile strength testing, in order to achieve elongations during processing which are at least 2 times those values.
“Symmetric algorithm”: A cryptographic algorithm using an identical key for both encryption and decryption.
Technical Note: A common use of symmetric algorithms is confidentiality of data.
“Systolic array computer”: A computer where the flow and modification of the data is dynamically controllable at the logic gate level by the user.
“Tape” is a material constructed of interlaced or unidirectional monofilaments, ‘strands’, rovings, tows, or yarns, etc., usually preimpregnated with resin.
N.B.: ‘Strand’ is a bundle of monofilaments (typically over 200) arranged approximately parallel “Technology means”, except as otherwise provided for against any item in the SCOMET List, information (including information embodied in software) other than information in the public domain, that is capable of being used in:
a. the development, production or use of any goods or software;
b. the development of, or the carrying out of, an industrial or commercial activity or the provision of a service of any kind.
Explanation 1: When technology is described wholly or partly by reference to the uses to which it (or the goods to which it relates) may be put, it shall include services which are provided or used, or which are capable of being used, in the development, production or use of such technology or goods.
Explanation 2:The information takes the form of 'technical data' or 'technical assistance'. Specified technology is defined in the General Technology Note to the SCOMET Category 8. Specified technology for the Munitions List is defined in 6A022.
Technical Notes:
1. 'Technical data' may take forms such as blueprints, plans, diagrams, models, formulae, tables, engineering designs and specifications, manuals and instructions written or recorded on other media or devices such as disk, tape, read-only memories.
2. 'Technical assistance' may take forms such as instruction, skills, training, working knowledge, consulting services. 'Technical assistance' may involve transfer of 'technical data'.
Appendix 3 – SCOMET List
“Three dimensional integrated circuit”: A collection of semiconductor dies or active device layers, integrated together, and having through semiconductor via connections passing completely through an interposer, substrate, die or layer to establish interconnections between the device layers. An interposer is an interface that enables electrical connections.
“Tilting spindle”: A tool-holding spindle which alters, during the machining process, the angular position of its centre line with respect to any other axis.
“Time constant”: The time taken from the application of a light stimulus for the current increment to reach a value of 1- 1/e times the final value (i.e., 63% of the final value).
“Tip shroud”: A stationary ring component (solid or segmented) attached to the inner surface of the engine turbine casing or a feature at the outer tip of the turbine blade, which primarily provides a gas seal between the stationary and rotating components.
“Total control of flight”: Automated control of aircraft state variables and flight path to meet mission objectives responding to real time changes in data regarding objectives, hazards or other aircraft.
“Total digital transfer rate”: The number of bits, including line coding, overhead and so forth per unit time passing between corresponding equipment in a digital transmission system. (See also digital transfer rate)
“Tow”: is a bundle of monofilaments, usually approximately parallel.
“Toxins”: means toxins in the form of deliberately isolated preparations or mixtures, no matter how produced, other than toxins present as contaminants of other materials such as pathological specimens, crops, foodstuffs or seed stocks of microorganisms.
“Transfer laser”: A laser in which the lasing species is excited through the transfer of energy by collision of a nonlasing atom or molecule with a lasing atom or molecule species.
“Tunable”: The ability of a laser to produce a continuous output at all wavelengths over a range of several laser transitions. A line selectable laser produces discrete wavelengths within one laser transition and is not considered tunable.
“Unidirectional positioning repeatability”: The smaller of values R↑ and R↓ (forward and backward), as defined by
3.21 of ISO 230-2:2014 or national equivalents, of an individual machine tool axis as applicable.
“Unmanned aerial vehicle (UAV)”: Any aircraft capable of initiating flight and sustaining controlled flight and navigation without any human presence on board.
“Usable in, usable for, usable as or capable of”: qualifies the description of equipment, parts, components, materials, technology or software which are suitable for a particular purpose. There is no requirement that the equipment, parts, components, technology or software should have been configured, modified or specified for that particular purpose. (Contrast with specially designed – see above).
“Use”: Operation, installation (including on-site installation), maintenance (checking), repair, overhaul and refurbishing.
“User-accessible programmability”: The facility allowing a user to insert, modify or replace program by means other than:
a. A physical change in wiring or interconnections; or
b. The setting of function controls including entry of parameters.
“Vaccine”: is a medicinal product in a pharmaceutical formulation licensed by, or having marketing or clinical trial authorisation from, the regulatory authorities of either the country of manufacture or of use, which is intended to stimulate a protective immunological response in humans or animals in order to prevent disease in those to whom or to which it is administered.
Appendix 3 – SCOMET List
“Vacuum atomization”: A process to reduce a molten stream of metal to droplets of a diameter of 500 µm or less by the rapid evolution of a dissolved gas upon exposure to a vacuum.
“Variable geometry airfoils”: Use trailing edge flaps or tabs, or leading edge slats or pivoted nose droop, the position of which can be controlled in flight.
“Yarn” is a bundle of twisted ‘strands’.
N.B.: ‘Strand’ is a bundle of monofilaments (typically over 200) arranged approximately parallel.
Appendix 3 – SCOMET List
ACRONYMS AND ABBREVIATIONS
Acronym Or Meaning
Abbreviation
ADC Analogue-To-Digital Converter
AGMA American Gear Manufacturers’ Association
AHRS Attitude And Heading Reference Systems
AISI American Iron And Steel Institute
ALE Atomic Layer Epitaxy
APP Adjusted Peak Performance
APU Auxiliary Power Unit
ASTM American Society For Testing And Materials
ATC Air Traffic Control
BJT Bipolar Junction Transistors
BPP Beam Parameter Product
BSC Base Station Controller
C3I Command, Communications, Control & Intelligence
CAD Computer-Aided-Design
CAS Chemical Abstracts Service
CCD Charge Coupled Device
CDU Control And Display Unit
CEP Circular Error Probable
CMM Coordinate Measuring Machine
CMOS Complementary Metal Oxide Semiconductor
CNTD Controlled Nucleation Thermal Deposition
CPLD Complex Programmable Logic Device
CPU Central Processing Unit
CVD Chemical Vapour Deposition
CW Chemical Warfare
CW (for lasers) Continuous Wave
DAC Digital-To-Analogue Converter
DANL Displayed Average Noise Level
DBRN Data-Base Referenced Navigation
DDS Direct Digital Synthesizer
DEW Directed Energy Weapon Systems
DMA Dynamic Mechanical Analysis
DME Distance Measuring Equipment
DMOSFET Diffused Metal Oxide Semiconductor Field Effect Transistor DS Directionally Solidified
EB Exploding Bridge
EB-PVD Electron Beam Physical Vapour Deposition
EBW Exploding Bridge Wire
ECM Electro-Chemical Machining
EDM Electrical Discharge Machines
EEPROMS Electrically Erasable Programmable Read Only Memory Appendix 3 – SCOMET List
EFI Exploding Foil Initiators
EIRP Effective Isotropic Radiated Power
EMC Electromagnetic Compatibility
EMCDB Elastomer Modified Cast Double Based Propellants
ERF Electrorheological Finishing
ERP Effective Radiated Power
ETO Emitter Turn-Off Thyristor
ETT Electrical Triggering Thyristor
FADEC Full Authority Digital Engine Control
FFT Fast Fourier Transform
FPGA Field Programmable Gate Array
FPIC Field Programmable Interconnect
FPLA Field Programmable Logic Array
FPO Floating Point Operation
FWHM Full-Width Half-Maximum
GISN General "Information Security" Note
GNSS Global Navigation Satellite System
GSM Global System For Mobile Communications
GST General Software Note
GTN General Technology Note
GTO Gate Turn-Off Thyristor
GLONASS Global Navigation Satellite System
GPS Global Positioning System
HBT Hetero-Bipolar Transistors
HEMT High Electron Mobility Transistors
ICAO International Civil Aviation Organisation
IEC International Electro-Technical Commission
IED Improvised Explosive Device
IEEE Institute Of Electrical And Electronic Engineers
IFOV Instantaneous-Field-Of-View
IGBT Insulated Gate Bipolar Transistor
IGCT Integrated Gate Commutated Thyristor
IHO International Hydrographic Organization
ILS Instrument Landing System
IMU Inertial Measurement Unit
INS Inertial Navigation System
IP Internet Protocol
IRS Inertial Reference System
IRU Inertial Reference Unit
ISA International Standard Atmosphere
ISAR Inverse Synthetic Aperture Radar
ISO International Organization For Standardization
ITU International Telecommunication Union
JT Joule-Thomson
LIDAR Light Detection And Ranging
Appendix 3 – SCOMET List
LIDT Laser Induced Damage Threshold
LOA Length Overall
LRU Line Replaceable Unit
LTT Light Triggering Thyristor
LVDT Linear Variable Differential Transformer
Mach Ratio Of Speed Of An Object To Speed Of Sound (After Ernst Mach)
MLS Microwave Landing Systems
MMIC Monolithic Microwave Integrated Circuit
MOCVD Metal Organic Chemical Vapour Deposition
MOSFET Metal-Oxide-Semiconductor Field Effect Transistor
MPM Microwave Power Module
MRAM Magnetic Random Access Memory
MRF Magnetorheological Finishing
MRF Minimum Resolvable Feature Size
MRI Magnetic Resonance Imaging
MTBF Mean-Time-Between-Failures
Mtops Million Theoretical Operations Per Second
MTTF Mean-Time-To-Failure
NA Numerical Aperture
NDT Non-Destructive Test
NEQ Net Explosive Quantity
OAM Operations, Administration Or Maintenance
OSI Open Systems Interconnection
PAI Polyamide-Imides
PAR Precision Approach Radar
PCL Passive Coherent Location
PIN Personal Identification Number
PMR Private Mobile Radio
PPM Parts Per Million
PVD Physical Vapour Deposition
QAM Quadrature-Amplitude-Modulation
RAP Reactive Atom Plasmas
RF Radio Frequency
RNC Radio Network Controller
RPV Remotely Piloted Air Vehicles
S-FIL Step And Flash Imprint Lithography
SAR Synthetic Aperture Radar
SAS Synthetic Aperture Sonar
SC Single Crystal
SCR Silicon Controlled Rectifier
SFDR Spurious Free Dynamic Range
SHPL Super High Powered Laser
SLAR Sidelooking Airborne Radar
SOI Silicon-On-Insulator
SPLD Simple Programmable Logic Device
Appendix 3 – SCOMET List
SQUID Superconducting Quantum Interference Device
SRA Shop Replaceable Assembly
SRAM Static Random Access Memory
SSB Single Sideband
SSR Secondary Surveillance Radar
SSS Side Scan Sonar
TE-PVD Thermal Evaporation-Physical Vapour Deposition
TIR Total Indicated Reading
TVR Transmitting Voltage Response
UTS Ultimate Tensile Strength
VJFET Vertical Junction Field Effect Transistor
VOR Very High Frequency Omni-Directional Range
WLAN Wireless Local Area Network
Appendix 3 – SCOMET List
Category 0: Nuclear materials, nuclear-related other materials, equipment and technology
Note: Export of these items is regulated under the Atomic Energy Act, 1962 and rules framed, and notifications/orders issued there under from time-to-time by the Department of Atomic Energy. The licensing authority for items in this category is the Department of Atomic Energy. An application for licence to export shall be made in writing to the Joint Secretary (I&M), Department of Atomic Energy, Anushakti Bhavan, CSM Marg, Mumbai 400 001
0A PRESCRIBED SUBSTANCES
Note: Any radioactive material in Category 0A shall additionally attract the provisions of Radiation Protection Rules, 2004 made under the Atomic Energy Act, 1962 and the provisions of Section-16 of the Atomic Energy Act, 1962.
0A1 Source Material
0A101 Uranium containing the mixture of isotopes occurring in nature.
0A102 Uranium depleted in the isotope 235.
0A103 Thorium.
0A104 Any of the materials specified above in 0A101, 0A102, or 0A103 in the form of metal, alloy, chemical compound, or concentrate.
0A105 Any other material containing one or more of the foregoing.
Note 1:
Source material includes uranium and thorium ores or concentrates.
Note 2:
Exports of following items, for the use only in non-nuclear activities, to a given recipient country, within a period of one calendar year, not exceeding the limits specified below, are not controlled:
a. Uranium (containing the mixture of isotopes in nature): 100 kilograms.
b. Depleted uranium (uranium depleted in the isotope 235 below that occurring in nature): 1000 kilograms.
c. Thorium: 1000 kilograms.
Note 3: 0A1 does not control following –
i. Uranium and thorium ores, mineral concentrates or other materials that contain less
than 300 parts per million (ppm) of uranium or/and thorium;
ii. Alloys containing less than 5 % thorium;
iii. Ceramic products containing thorium, which have been manufactured for non-nuclear use.
0A2 Special Fissionable Material
0A201 Plutonium-239.
0A202 Uranium-233.
0A203 Uranium enriched in the isotopes 235 or 233.
0A204 Neptunium.
0A205 Any material containing one or more of the foregoing.
0A206 Such other fissionable material determined by the Central Government from time to time.
Technical note:
The term “uranium enriched in the isotopes 235 or 233” means uranium containing the isotopes 235 or 233 or both in an amount such that the abundance ratio of the sum of these isotopes to the isotope 238 is greater than the ratio of the isotope 235 to the isotope 238 occurring in nature.
Appendix 3 – SCOMET List
Note:
1. The term “special fissionable material” does not include source material.
2. Any quantity of special fissionable material is prescribed substance.
3. 0A2 does not control -
a. Plutonium with an isotopic concentration of plutonium-238 exceeding 80%, and
b. Special fissionable material when used in gram quantities or less as a sensing component in instruments.
0A3 Other Materials
‘Other Materials’ means non-nuclear materials for reactors, nuclear related dual-use materials indicated below and such materials as determined by the Central Government from time to time.
0A301 Deuterium and heavy water
Deuterium, heavy water (deuterium oxide) and any other deuterium compound, in which the ratio of deuterium to hydrogen atoms exceeds 1:5000,
a. for use in a nuclear reactor in quantities exceeding 5 kilograms of deuterium atoms in one consignment or 25 kilograms of deuterium atoms, for any one
recipient country within a period of one calendar year;
b. for use in a non-nuclear activity in quantities exceeding 200 kilograms of
deuterium atoms, for any one recipient country within a period of one calendar year.
0A302 Nuclear grade graphite
Nuclear grade graphite having a purity level better than 5 parts per million (ppm) boron equivalent and with a density greater than 1.5 gram/cc -
a. for use in a nuclear reactor or any other nuclear activities in quantities exceeding 1 kilogram;
b. for use in non-nuclear activities in quantities exceeding 30 metric tons for any one recipient country within a period of one calendar year.
Note: The item 0A302 does not cover graphite powder.
0A303 Zirconium with hafnium content of less than 1 part to 500 parts of zirconium by weight (i.e. less than 2000 ppm) in the form of metal, alloys containing more than 50% zirconium by weight, compounds, manufactures thereof, waste or scrap of any of the foregoing.
0A304 Beryllium metal, its compounds, alloys containing more than 50% beryllium by weight, manufactures thereof, and waste or scrap of any of the foregoing and its minerals / concentrates including beryl but excluding:
a. beryllium windows used for x-ray machines or for bore-hole logging devices, and
b. beryl in the form of emerald, aquamarine or ‘cut & polished’ semi-precious stones for use in jewellery.
0A305 Lithium enriched in the Lithium-6 (6 Li) isotope to greater than its natural isotopic abundance (i.e. more than 7.5%) and the products or devices containing enriched lithium such as elemental lithium, alloys, compounds, mixtures containing lithium, manufactures thereof, waste or scrap of any of the foregoing.
0A306 Niobium and Tantalum, their metals, alloys and minerals including columbite and tantalite.
0A307 [Reserved]
0A308 Tritium, tritium compounds or mixtures containing tritium in which the ratio of tritium to hydrogen atoms exceeds 1 part in 1000, except when utilized in such quantities and for such purposes as for organic labelled compounds, Gas Filled Light Sources and as Tritiated Water for radiotracer studies.
0A309 Hafnium
Hafnium metal, alloys containing more than 60% hafnium by weight, hafnium compounds containing more than 60% hafnium by weight, manufactures thereof, and waste or scrap of any of Appendix 3 – SCOMET List
the foregoing.
0A310 Radium-226
Radium-226 (226Ra), radium-226 alloys, radium-226 compounds, mixtures containing radium- 226, manufactures thereof, and products or devices containing any of the foregoing, except medical applicators and a product or device containing less than 0.37 GBq (10mCi) of Ra-226 in any form.
0A311 Boron
Boron enriched in the Boron-10 (10B) isotope to greater than its natural isotopic abundance as follows:
Elemental boron, compounds, mixtures containing boron, manufactures thereof, waste or scrap of any of the foregoing.
0A312 Helium-3
Helium-3 (3He), mixtures containing helium-3, and products or devices containing any of the foregoing.
Note: A product or device containing less than 1gm of Helium-3 is excluded.
0A313 ‘Radionuclides’ appropriate for making neutron sources based on alpha-n reaction, in the following forms:
a. Elemental;
b. Compounds having a total activity of 37 GBq per kg or greater;
c. Mixtures having a total activity of 37 GBq per kg or greater;
d. Products or devices containing any of the foregoing.
Radionuclides controlled by this item include:
| Actinium-225 Curium-240 Curium-243 Einsteinium254 Plutonium-238 Polonium-208 Thorium-227 | Actinium-227 Curium-241 Curium244 Gadolinium-148 Polonium-209 Radium-223 Uranium-230 | Californium-253 Curium-242 Einsteinium-253 Plutonium-236 Polonium-210 Thorium-228 Uranium-232 |
0B Prescribed Equipment
0B001 Nuclear Reactors; associated equipment, components, and systems especially designed, prepared, or adapted or used or intended to be used in such reactors including but not limited to:-
a. Complete nuclear reactors
b. Nuclear reactor vessels
c. Nuclear reactor fuel charging and discharging machines
d. Nuclear reactor control rods and equipment
e. Nuclear reactor pressure tubes
f. Nuclear fuel cladding: Zirconium metal tubes or zirconium alloy tubes (or assemblies of tubes), in which hafnium to zirconium ratio is 1:500 or less, for use as nuclear fuel cladding
g. Primary coolant pumps or circulators
h. Nuclear reactor internals
i. Heat exchangers (steam generators) for use in the primary or intermediate coolant circuit of a nuclear reactor
j. Neutron detectors
k. External thermal shields.
0B002 Plants for processing, production, concentration, conversion or recovery of Prescribed Substances (such as uranium, plutonium, thorium, deuterium, heavy water, tritium, lithium); associated equipment, components and systems especially designed, prepared or adapted or used or intended to Appendix 3 – SCOMET List
be used in such plants including but not limited to:
a. Plants for production or concentration of deuterium, heavy water or deuterium compounds-
1. Water - Hydrogen Sulphide Exchange Towers with diameters of 1.5 m or greater and capable of operating at pressures greater than or equal to 2 MPa (300 psi),
especially designed or prepared for heavy water production.
2. Especially designed or prepared blowers and compressors for hydrogen-sulphide gas circulation. These blowers or compressors have a throughput capacity greater
than or equal to 56 m3/second (120,000 SCFM) while operating at pressures
greater than or equal to 1.8 MPa (260 psi) suction and have seals designed for wet H2S service
3. Ammonia-Hydrogen Exchange Towers greater than or equal to 35 m in height
with diameters of 1.5 m to 2.5 m capable of operating at pressures greater than
15 MPa especially designed or prepared for heavy water production
4. Tower Internals and Stage Pumps: Tower internals and stage pumps especially
designed or prepared for heavy water production. Tower internals include
especially designed stage contactors which promote intimate gas/liquid contact.
Stage pumps include especially designed submersible pumps for circulation of
liquid ammonia within a contacting stage internal to the stage towers.
5. Ammonia Crackers with operating pressures greater than or equal to 3 MPa
especially designed or prepared for heavy water production.
6. Infrared Absorption Analyzers capable of ‘on-line’ hydrogen/deuterium ratio analysis
7. Catalytic Burners for conversion of enriched deuterium gas into heavy water
8. Complete heavy water upgrade systems or columns therefor
9. Ammonia synthesis converters or synthesis units for heavy water production
utilizing the ammonia-hydrogen exchange process.
b. Plants for the conversion of uranium
1. Systems for the conversion of uranium ore concentrates to UO3;
2. Systems for the conversion of UO3 to UF6;
3. Systems for the conversion of UO3 to UO2;
4. Systems for the conversion of UO2 to UF4;
5. Systems for the conversion of UF4 to UF6;
6. Systems for the conversion of UF4 to uranium metal;
7. Systems for the conversion of UF6 to UO2;
8. Systems for the conversion of UF6 to UF4;
9. Systems for the conversion of UO2 to UCl4.
c. Plants for the conversion of plutonium
1. Systems for the conversion of plutonium nitrate to oxide
2. Systems for plutonium metal production
d. Tritium facilities or plants for the production, recovery, extraction, concentration or
handling of tritium and equipment therefor including hydrogen or helium
refrigeration units; and hydrogen isotope storage or purification systems using metal hydrides as the storage or purification medium.
e. Lithium isotope separation facilities or plants, and systems and equipment therefor as follows -
1. Facilities or plants for the separation of lithium isotopes;
2. Equipment for the separation of lithium isotopes based on the lithium-mercury amalgam process, as follows:
a) Packed liquid-liquid exchange columns especially designed for lithium
amalgams;
b) Mercury or lithium amalgam pumps;
c) Lithium amalgam electrolysis cells;
d) Evaporators for concentrated lithium hydroxide solution;
Appendix 3 – SCOMET List
3. Ion exchange systems especially designed for lithium isotope separation, and
especially designed component parts therefor;
4. Chemical exchange systems (employing crown ethers, cryptands, or lariat ethers) especially designed for lithium isotope separation, and especially designed component parts therefor.
0B003 Plants for reprocessing of irradiated nuclear fuel and equipment, components and systems especially designed, prepared or adapted or used or intended to be used in such plants, including but not limited
to:
a. Irradiated fuel element chopping machines designed for remote operation
b. Dissolvers capable of withstanding hot and highly corrosive liquid for dissolution of
irradiated nuclear fuel and which can be remotely loaded and maintained
c. Solvent extractors and solvent extraction equipment resistant to the corrosive effect of nitric acid
d. Chemical holding or storage vessels resistant to the corrosive effect of nitric acid
e. Neutron measurement systems for integration and use with automated process control systems for the reprocessing of irradiated fuel elements.
f. Industrial equipment including assemblies and components as follows:
1. High density (lead glass or other) radiation shielding windows
2. Radiation hardened TV cameras, or lenses therefor
3. ‘Robots’ or ‘end effectors’ especially designed for handling high explosives; and control units therefor
4. Remote manipulators that can be used to provide remote actions in radiochemical separation operations or hot cells
0B004 Plants for treatment, handling, storage and transportation of radioactive wastes from nuclear reactors or from plants for processing Source Materials or Special Fissionable Materials or from nuclear reprocessing plants; irradiated nuclear fuel; Special Fissionable Materials, and equipment especially designed, prepared, adapted, or intended to be used therefor.
0B005 All systems, associated equipment, components for separation or enrichment of isotopes of uranium, plutonium, lithium, boron or other elements, other than analytical instruments, especially designed, prepared, adapted, used or intended to be used therefor as follows:
a. Gas centrifuges and assemblies and components especially designed or prepared for use in gas Centrifuges
1. Gas centrifuges;
2. Complete rotor assemblies; Thin-walled cylinders, or a number of interconnected thinwalled cylinders, manufactured from one or more of the high strength-to-density ratio materials described in the Note-1 in 0B005.a. If interconnected, the cylinders are joined together by flexible bellows or rings as described in 0B005.a.4. The rotor is fitted with an
internal baffle(s) and end caps, as described in 0B005.a.5 and 0B005.a.6.
3. Rotor tube cylinders: Especially designed or prepared thin-walled cylinders with thickness of 12 mm or less, a diameter of between 75 mm and 650 mm, and manufactured from one or more of ‘high strength-to-density ratio materials’ described in the Note-1 in 0B005.a;
4. Rings or bellows: Rings or bellows with wall thickness of 3 mm or less and a diameter of between 75 mm and 650 mm especially designed to give local support to a rotor tube or to join together a number of rotor tubes, made from ‘high strength-to-density ratio materials’ described in the Note-1 in 0B005.a.
5. Baffles: Disc-shaped components of between 75 mm and 650 mm diameter especially designed or prepared for mounting inside a rotor tube, in order to isolate the take-off chamber from the main separation chamber and manufactured from ‘high strength-todensity ratio materials’ described in the Note-1 in 0B005.a.
6. Top or bottom caps: Especially designed or prepared disc-shaped components of between 75 mm and 400 mm diameter especially designed or prepared to fit the ends of a rotor tube, and so contain the UF6 within the rotor tube, and in some cases to support, retain or contain as an integrated part an element of the upper bearing (top cap) or to carry the rotating elements Appendix 3 – SCOMET List
of the motor and lower bearing (bottom cap), and manufactured from ‘high strength-todensity ratio materials’ described in the Note-1 in 0B005.a;
7. Especially prepared Magnetic Suspension Bearings with both of the following attributes:
a. Bearing assemblies consisting of an annular magnet suspended within a housing made of or protected by “materials resistant to corrosion by UF6” (see Note 3 of 0B005) containing a damping medium and having the magnet coupling with a pole piece or second magnet fitted to the top cap of the rotor;
b. Active magnetic bearings especially designed or prepared for use with gas centrifuges. These bearings usually have the following characteristics: i) Designed to keep centred a rotor spinning at 600 Hz or more; and ii) Associated to a reliable electrical power supply and/or to an uninterruptible power supply (UPS) unit in order to function for more than one hour.
8. Bearings / Dampers: Especially designed or prepared bearings comprising a pivot/cup assembly mounted on a damper. The pivot is normally a hardened steel shaft with a hemisphere at one end with a means of attachment to the bottom cap described in 0B005.a.6 at the other. The shaft may however have a hydrodynamic bearing attached. The cup is pellet-shaped with a hemispherical indentation in one surface. These components are often supplied separately to the damper.
9. Molecular pumps: Molecular pumps are high vacuum pumps consisting of especially designed or prepared cylinders having internally machined or extruded helical grooves and internally machined bores. Typical dimensions are as follows: 75 mm to 650 mm internal diameter, 10 mm or more wall thickness, with the length equal to or greater than the diameter. The grooves are typically rectangular in cross-section and 2 mm or more in depth.
10. Ring-shaped motor stators: Especially designed or prepared ring-shaped stators for high speed multiphase AC hysteresis (or reluctance) motors for synchronous operation within a vacuum at a frequency of 600 Hz or greater and a power of 40 VA or greater. The stators may consist of multi-phase windings on a laminated low loss iron core comprised of thin layers typically 2.0 mm thick or less.
11. Centrifuge housing/recipients to contain the rotor tube assembly of a gas centrifuge consisting of rigid cylinder of wall thickness up to 30 mm with precision machined ends that are parallel to each other and perpendicular to the cylinder's longitudinal axis to within 0,05 degrees or less.
12. Scoops consisting of tubes for the extraction of UF6 gas from within the rotor tube by a Pitot tube action and capable of being fixed to the central gas extraction system.
Note 1: The high strength-to-density ratio materials used for centrifuge rotating components include the following:
(a) Maraging steel capable of an ultimate tensile strength of 1.95 GPa or more;
(b) Aluminium alloys capable of an ultimate tensile strength of 0.46 GPa or more;
(c) Filamentary materials suitable for use in composite structures and having a specific modulus of 3.18 X 106 m or greater and a specific ultimate tensile strength of 7.62 X 104 m or greater.
Note 2: 'Specific Modulus' is the Young's Modulus in N/m2 divided by the specific weight in N/m3; 'Specific Ultimate Tensile Strength' is the ultimate tensile strength in N/m2 divided by the specific weight in N/ m3.
b. Especially designed or prepared auxiliary systems, equipment and components for gas centrifuge enrichment plants
1. Machine header piping systems for handling UF6 within the centrifuge cascades;
2. Frequency changers (converters or inverters) especially designed or prepared to supply motor stators for gas centrifuge enrichment, having all of the following characteristics, and especially designed components therefor:
a. A multiphase frequency output of 600 Hz or greater; and
b. High stability (with frequency control better than 0.2 %).
c. Especially designed or prepared assemblies and components for use in gaseous diffusion enrichment
1. Gaseous diffusion barriers and barrier materials resistant to corrosion by UF6 described in the Note-3 in 0B005;
2. Gaseous diffuser housings made of or protected by materials resistant to corrosion by UF6 Appendix 3 – SCOMET List
described in the Note-3 in 0B005;
3. Compressors (positive displacement, centrifugal and axial flow types) or gas blowers with a suction volume capacity of 1 m3 /min or more of UF6, discharge pressure up to 500 kPa and having a pressure ratio of 10:1 or less designed for long term operation in the UF6 environment and made of or protected by materials resistant to corrosion by UF6 described in the Note-3 in 0B005.
d. Especially designed or prepared auxiliary systems, equipment and components for use in gaseous diffusion enrichment:
Piping systems and header systems for handling UF6 within the gaseous diffusion cascades.
e. Especially designed or prepared systems, equipment and components for use in aerodynamic enrichment plants:
1. Especially designed or prepared separation nozzles and assemblies thereof. The separation nozzles consist of slit-shaped, curved channels having a radius of curvature less than 1 mm, made of materials resistant to corrosion by UF6 described in the Note-3 in 0B005 and having a knife-edge within the nozzle that separates the gas flowing through the nozzle into two fractions;
2. Especially designed or prepared vortex tubes and assemblies thereof. The vortex tubes are cylindrical or tapered, made of or protected by materials resistant to corrosion by UF6 described in the Note-3 in 0B005 and with one or more tangential inlets. The tubes may be equipped with nozzle type appendages at either or both ends;
3. Especially designed or prepared compressors or gas-blowers made of or protected by materials resistant to corrosion by the UF6 (see the Note-3 in 0B005) / carrier gas (hydrogen or helium) mixture;
4. Especially designed or prepared separation element housings made of or protected by materials resistant to corrosion by UF6 described in the Note-3 in 0B005, for containing vortex tubes or separation nozzles;
5. Especially designed or prepared header-piping systems, made of or protected by materials resistant to corrosion by UF6 described in the Note-3 in 0B005, for handling UF6 within the aerodynamic cascades;
6. UF6/carrier gas separation systems for separating UF6 from carrier gas (hydrogen or helium).
f. Especially designed or prepared systems, equipment and components for use in chemical exchange or ion exchange enrichment plants.
1. Countercurrent Liquid-liquid exchange columns (Chemical exchange), having mechanical power input, especially designed or prepared for uranium enrichment using the chemical exchange process. For corrosion resistance to concentrated hydrochloric acid solutions, these columns and their internals are normally made of or protected by materials resistant to corrosion by concentrated hydrochloric acid solutions. The stage residence time of the columns is normally designed to be 30 seconds or less.
2. Liquid-liquid centrifugal contactors (Chemical exchange), especially designed or prepared for uranium enrichment using the chemical exchange process. Such contractors are made of or protected by materials resistant to corrosion by concentrated hydrochloric acid solutions, The stage residence time of the columns is normally designed to be 30 seconds or less.
3. Uranium reduction systems and equipment (Chemical exchange):
a. Especially designed or prepared electrochemical reduction cells to reduce uranium from one valence state to another for uranium enrichment using the chemical exchange process. The cell materials in contact with process solutions must be corrosion resistant to concentrated hydrochloric acid solutions;
b. Especially designed or prepared systems consisting of solvent extraction equipment and pumps or other transfer devices at the product end of the cascade for taking the U+4 out of the organic stream.
4. Feed preparation systems (Chemical exchange) consisting of dissolution, solvent extraction and/or ion exchange equipment for producing high-purity uranium chloride.
5. Uranium oxidation systems (Chemical exchange) for oxidation of U+3 to U+4 Appendix 3 – SCOMET List
6. Fast-reacting ion exchange resins/adsorbents (Ion exchange):
Fast-reacting ion-exchange resins or adsorbents, especially designed or prepared for uranium enrichment using the chemical exchange process, including porous macroreticular resins, and/or pellicular structures and other composite structures in any suitable form including particles or fibres chemically resistant to concentrated hydrochloric acid solutions.
7. Ion exchange columns (Ion exchange):
Cylindrical columns for containing and supporting packed beds of ion exchange resin/adsorbent and made of or protected by materials resistant to corrosion by concentrated hydrochloric acid solutions.
8. Ion exchange reflux systems (Ion exchange):
Chemical or electrochemical oxidation or reduction systems for regeneration of the chemical oxidizing or reducing agent(s) used in ion exchange enrichment cascades.
g. Especially designed or prepared systems, equipment and components for use in laser-based enrichment plants.
1. Uranium vaporization systems (atomic vapour based methods)
2. Liquid or vapour uranium metal handling systems and components (atomic vapour based methods)
3. Uranium metal ‘product’ and ‘tails’ collector assemblies (atomic vapour based methods)
4. Separator module housings (atomic vapour based methods)
5. Supersonic expansion nozzles (molecular based methods)
6. ‘Product’ or ‘tails’ collectors (molecular based methods)
7. UF6/carrier gas compressors (molecular based methods)
8. Rotary shaft seals (molecular based methods)
9. Fluorination systems (molecular based methods)
10. UF6/carrier gas separation systems (molecular based methods)
11. ‘Lasers’ or ‘laser systems or components’ for the separation of uranium isotopes.
h. Especially designed or prepared systems, equipment and components for use in plasma separation enrichment plants
1. Microwave power sources and antennae: Especially designed or prepared microwave power sources and antennae for producing or accelerating ions and having the following characteristics: greater than 30 GHz frequency and greater than 50 kW mean power output for ion production.
2. Radio frequency ion excitation coils for frequencies of more than 100 kHz
3. Uranium plasma generation systems
4. Uranium metal ‘product’ and ‘tails’ collector assemblies made of or protected by materials resistant to the heat and corrosion of uranium metal vapour.
5. Separator module housings (cylindrical vessels) for containing the uranium plasma source, radio-frequency drive coil and the ‘product’ and ‘tails’ collectors.
i. Especially designed or prepared systems, equipment and components for use in electromagnetic enrichment plants.
1. Electromagnetic isotope separators for separation of uranium isotopes and equipment and components therefor, including ion sources (consisting of a vapour source, ionizer, and beam accelerator), ion collectors (consisting of collector plates), vacuum housings and magnet pole pieces;
2. High voltage power supplies for ion sources: Especially designed or prepared high-voltage power supplies for ion sources, having all of the following characteristics: capable of continuous operation, output voltage of 20,000 V or greater, output current of 1 A or greater, and voltage regulation of better than 0.01% over a time period of 8 hours
3. High-power, direct current magnet power supplies: Especially designed or prepared highpower, direct current magnet power supplies having all of the following characteristics: capable of continuously producing a current output of 500 A or greater at a voltage of 100 V or greater and with a current or voltage regulation better than 0.01% over a period of 8 hours.
Appendix 3 – SCOMET List
j. Especially designed or prepared other equipment and components for use in enrichment plants:
1. Feed systems / product and tails withdrawal systems such as feed autoclaves, ovens, or systems, desublimers, cold traps or pumps, solidification or liquefaction stations, ‘product’ or ‘tails’ stations used for handling UF6;
2. Special shut-off valves, control valves, bellow sealed valves, manual or automated, shut-off
or control, made of or protected by materials resistant to corrosion by UF6;
3. UF6 mass spectrometers / ion sources capable of taking on-line samples from UF6 gas stream; ;
4. Rotary shaft seals for compressors or blowers;
5. Heat exchangers made of or protected by “materials resistant to corrosion by UF6”;
6. Vacuum systems including vacuum manifolds, vacuum headers and vacuum pumps made of, or protected by, materials resistant to corrosion by UF6.
Notes to 0B005:
1: Controls under 0B005 also apply to the plants and equipment that are intended for isotope separation of other elements.
2: “Other elements” means all elements other than hydrogen, uranium and plutonium. 3: Materials resistant to corrosion by UF6 include copper, copper alloys, stainless steel, aluminium, aluminium oxide, aluminium alloys, nickel or alloys containing 60% or more nickel and fluorinated hydrocarbon polymers.
0B006 Plants for the fabrication of nuclear reactor fuel elements, and equipment especially designed or prepared therefor including but not limited to:
a. fully automatic pellet inspection stations especially designed or prepared for checking final dimensions and surface defects of the fuel pellets;
b. automatic welding machines especially designed or prepared for welding end caps onto the fuel pins (or rods);
c. automatic test and inspection stations especially designed or prepared for checking the integrity of completed fuel pins (or rods);
d. systems especially designed or prepared to manufacture nuclear fuel cladding.
Item ‘c’ typically includes equipment for: 1) x-ray examination of pin (or rod) end cap welds, 2) helium leak detection from pressurized pins (or rods), and 3) gamma-ray scanning of the pins (or rods) to check for correct loading of the fuel pellets inside.
0B007 Plants or systems for production, handling, storage and transportation of Radioisotopes in quantities exceeding 100 Curies (3.7 X 1012 Becquerel).
0B008 Neutron generators including neutron chain reacting assemblies and fusion assemblies of all kinds for producing fissile materials.
0C Technology and software
Technology and software for the development, production or use of prescribed substances or prescribed equipment specified in 0A or 0B. ”
Appendix 3 – SCOMET List
Category 1 Toxic chemical agents and other chemicals
1A Export of the following chemicals is prohibited:
(This corresponds to Schedule 1 to the Chemical Weapons Convention (CWC))
Note: Where reference is made below to groups of di-alkylated chemicals, followed by a list of alkyl groups in parentheses, all chemicals possible by all possible combinations and alkyl groups listed in parentheses are considered prohibited unless explicitly exempted.
| (1). | O-Alky ( <C10 , incl. cycloalkyl) alky1 (Me, Et,n-Pr or i-Pr) phosphonofluoridates e.g. Sarin: O-Isopropy1 methylphosphonofluoridate Soman: O-Pinacolyl methylphosphonofluoridate |
| (2). | O-Alkyl, ( <C10, incl. cycloalkyl) N,N-dialky1 (Me, Et, n-Pr or i-Pr) phosphoramidocyanidates e.g. Tabun: O-Ethyl N,N,-dimethyl phosphoramidocyanidate |
| (3). | O-Alkyl (H or < C10, incl. cycloalkyl) S-2-Dialkyl (Me, Et, n-Pr or i-Pr)- aminoethyl alkyl (Me, Et, n-Pr or i-Pr) phosphonothiolates and corresponding alkylated or protonated salts e.g. VX: O-Ethyl S-2 diisopropylaminoethyl methyl phosphonothiolate |
| (4). | Sulphur mustards: 2-Chloroethylchloromethylsulphide Mustard gas: Bis (2-chloroethyl) sulphide Bis (2-chloroethylthio) methane Sesquimustard:1,2-Bis (2-chloroethylthio) ethane 1,3-Bis (2-chloroethylthio)-n-propane 1,4-Bis (2-chloroethylthio)-n-butane 1,5-Bis (2-chloroethylthio)-n-Pentane Bis (2-Chloroethylthiomethyl) ether O-Mustard: Bis (2-Chloroethylthiomethyl) ether |
| (5). | Lewisites: Lewisite 1: 2-Chlorovinyldichloroarsine Lewisite 2: Bis (2-Chlorovinyl) chloroarsine Lewisite 3: Tris (2-Chlorovinyl) arsine |
| (6). | Nitrogen mustards: HN1: Bis (2-chloroethyl) ethylamine HN2: Bis (2-chloroethyl) Chloroarsine HN3: Tris (2-chloroethyl) amine |
| (7). | Saxitoxin |
| (8). | Ricin |
| (9). | Alkyl (Me, Et, n-Pr or I-Pr) phosphonyldifluorides e.g. DF: Methyl phosphonyldifluoride |
| (10). | O-Alkyl (H or < C10, incl. cycloalkyl) O-2 dialkyl (Me, Et, n-Pr or i-Pr)- aminoethylalkyl (Me, Et N-Pr or i-Pr) phosphonites and corresponding alkylated or protonated salts e.g.QL: O-Ethyl O-2-diisopropylaminoethyl methyl phosphonite |
| (11). | Chlorosarin: O-Isopropyl methylphosphonochloridate |
| (12). | Chlorosoman: O-Pinacolyl methylphosphonochloridate Appendix 3 – SCOMET List |
| 1B Export Weapon (This | of chemicals listed in 1B below is permitted only to States party to the Chemical s Convention against an export licence corresponds to Schedule 2 to the Chemicals Weapons Convention) Note to exporters: (a) A list of States Parties can be obtained from the Disarmament & International Security Affairs Division of the Ministry of External Affairs (Room No. 40G, South Block, New Delhi) or at the official website of the Organization for the Prohibition of Chemical Weapons at www.opcw.org. (b) A general permission valid for a period of two years may be applied for export of chemicals in this category. This permission shall be subject to the condition that for each export consignment, exporters shall, within 30 days of exports, notify the details to the National Authority, Chemical Weapons Convention, Cabinet Secretariat; Ministry of External Affairs (D&ISA); Department of Chemicals and Petrochemicals and the Directorate General of Foreign Trade and submit to DGFT, a copy of Bill of Entry into the destination State Party within 30 days of delivery. Note: Where reference is made below to groups of dialkylated chemicals, followed by a list of alkyl groups in parentheses, all chemicals possible by all possible combinations and alkyl groups listed in parentheses are included unless explicitly exempted. 1. Amiton 0,0-Diethyl S-[2-(diethylamino) ethyl)] phosphorothiolate and corresponding alkylated or protonated salts 2. PFIB: 1,1,3,3,3,-Pentafluoro-2-(trifluoromethyl)1-propene 3. BZ: 3-Quinuclidinyl benzilate 4. Chemicals, except for those listed in Schedule 1, containing a phosphorus atom to which is bonded one methyl, ethyl or propyl (normal or iso) group but not further carbon atoms, e.g.Methylphosphonyl dichloride, Dimethyl methylphosphonate Exemption:- Fonofos: O-Ethyl S-phenyl ethylphosphonothiolothionate 5. N, N-Dialkyl (ME, Et, n-Pr or i-Pr) phosphoramidic dihalides 6. Dialkyl (Me, Et, n-Pr or i-Pr) N, N-dialkyl (Me, Et, n-Pr or i-Pr)-phosphoramidates 7. Arsenic trichloride 8. 2,2-Diphenyl-2 hydroxyacetic acid 9. Quinuclidine-3-ol 10. N,H-Dialkyl (Me, Et, n-Pr or i-Pr) aminoethyl-2 -chlorides and corresponding protonated salts 11. N, N-Dialkyl (Me, Et, n-Pr or i-Pr) aminoethane-2-ols and corresponding protonated salts Exemptions: N,N-Dimethylaminoethanol and corresponding protonated salts N,N-Diethylaminoethanol and corresponding protonated salts 12. N, N-Dialkyl (Me, Et, n-Pr or i-Pr) aminoethane-2-thiols and corresponding protonated salts 13. Thiodiglycol: Bis(2-hydroxyethyl) sulphide 14. Pinacolyl alcohol: 3,3-Dimethylbutane-2-ol |
A list of commercially important Schedule-2 Chemicals of CWC is given below :
| Sl.N 1 2 3 4 5 6 | SCOMET o. Name of Chemical Entry 1B001 2-Chloro N, N-Di-isopropyl ethyla 1B002 Diethyl amino Ethanethiol 1B003 O, O, Dimethyl Methyl Phosphonate 1B004 2-Hydroxy N, N-Diisopropyl Ethyla N, N-Diethyl Amino ethyl Chloride 1B005 Hydrochloride 1B006 Di-ethyl Amino ethanethiol Hydroc Appendix 3 – SCOMET List Di-Methyl Amino ethyl chloride | mine mine hloride | Entry into Schedule 2B10 2B12 2B04 2B11 2B10 2B12 | CAS number 4261-68-1 100-38-9 756-79-6 96-80-0 869-24-9 1942-52-5 | ITC (HS) code 29211910 29221910 29209045 29221111 29221112 29221113 | |
| 7 | 1B007 | 2B10 Hydrochloride | 4584-46-7 | 29221114 | ||
| 8 | 1B008 | Di-Methyl Amino ethanethiol 2B12 Di-Methyl Amino ethanethiol | 108-02-1 13242-44- | 29221115 | ||
| 9 | 1B009 | 2B12 Hydrochloride Phosphorothioic acid, S [2-(diethylamino) | 9 | 29221116 | ||
| 10 | 1B010 | 2A01 ethyl] O, O – diethyl ester 1-Propene, 1,1, 3, 3, 3, - Pentafluoro – 2- | 78-53-5 | 29201910 | ||
| 11 | 1B011 | 2A02 (trifluoromethyl) (PFIB) Benzeneacetic acid, alphahydroxy – alpha- | 382-21-8 | 29033911 | ||
| 12 | 1B012 | phenyl, 1 – azabicyclo [2.2.2.] oct-3-yl 2A03 ester Phosphonic Acid, Methyl-compound with | 1709855 84402-58- | 29392050 | ||
| 13 | 1B013 | 2B04 (aminoimino methyl) urea (1: 1) 1-Propanaminium N, N, N-trimethyl – 3- | 4 70055-71- | 29209047 | ||
| 14 | 1B014 | [1- oxo-9 octadecenyl) amino]-. (Z)- 2B04 methyl methylphosphonate Phosphonic acid, [methyl bis (5-ethyl-2- | 42595-45- | 29209048 | ||
| 15 | 1B015 | methyl-2-oxido-1, 3, 2- 2B04 dioxaphosphorinan- 5-yl) methyl] ester Phosphonic acid, [methyl-(5-ethyl-2- | 41203-81- | 29209051 | ||
| 16 | 1B016 | methyl 2-oxido-1,3,2-dioxaphosphorinan- 2B04 5-yl) methyl] ester | 18755-43- | 29209052 | ||
| 17 | 1B017 | Phosphonic acid, propyl-dimethyl ester 2B04 | 15715-41- | 29209053 | ||
| 18 | 1B018 | Phosphonous acid, methyl-diethyl ester 2B04 | 29209054 | |||
| 19 | 1B019 | Phosphonic acid, ethyl- 2B04 | 1782267 | 29209055 | ||
| 20 | 1B020 | Phosphonic acid, propyl- 2B04 | 4672-38-2 | 29209056 | ||
| 21 | 1B021 | Phosphinic acid, methyl- 2B04 Phosphonochloridic acid, methyl-, methyl | 4206-94-4 | 29209057 | ||
| 22 | 1B022 | 2B04 ester | 1066-52-0 | 29209058 | ||
| 23 | 1B023 | Phosphonothioic dichloride, ethyl- 2B04 | 993-43-1 | 29209061 | ||
| 24 | 1B024 | Phosphonic acid methyl- 2B04 | 993-13-5 | 29209062 | ||
| 25 | 1B025 | Phosphonic acid, methyl-, dimethyl ester 2B04 | 756-79-6 | 29209063 | ||
| 26 | 1B026 | Phosphonic dichloride, methyl- 2B04 | 676-97-1 | 29209064 | ||
| 27 | 1B027 | Phosphonous dichloride, methyl- 2B04 | 676-83-5 | 29209065 | ||
| 28 | 1B028 | Phosphonic acid, ethyl-, diethyl ester 2B04 | 78-38-6 | 29209066 | ||
| 29 | 1B029 | Arsenous trichloride 2B07 Benzeneacetic acid, alpha-hydroxy-alpha- | 7784-34-1 | 28121930 | ||
| 30 | 1B030 | 2B08 phenyl | 76-93-7 | 29181900 | ||
| 31 | 1B031 | 1-Azabicyclo (2.2.2.) octan-3-ol 2B09 | 1619-34-7 | 29333930 | ||
| 32 | 1B032 | Ethanamine, 2-Chloro-N, N-dimethyl- 2B10 | 107-99-3 | 29211920 | ||
| 33 | 1B033 | Ethanol, 2-[bis(1-methylethyl ) amino ]- 2B11 | 96-80-0 | 29221920 | ||
| 34 | 1B034 | Ethanethiol, 2-(diethylamino)- 2B12 | 100-38-9 | 29221930 | ||
| 35 | 1B035 | Ethanol, 2, 2’-thiobis- 2B13 | 111-48-8 | 29309091 | ||
| 36 | 1B036 | 2-Butanol, 3, 3-dimethyl- 2B14 | 464-07-3 | 29051910 | ||
| 37 | 1B037 | Others - Appendix 3 – SCOMET List | - | - | ||
| 1C | Export | of Chemicals listed in 1C below is allowed to State | Parties to t | he CWC withou | t an |
export licence subject to the condition that the exporter shall notify within 30 days of export to the National Authority, Chemicals Weapons Convention, Cabinet Secretariat; the Ministry of External Affairs (D&ISA); the Department of Chemicals & Petro-chemicals, and the DGFT of such exports in the prescribed format (Aayat Niryat Form ) along with the End-Use Certificate and submit to the DGFT a copy of the bill of entry into the destination State Party within 30 days of delivery.
Export of chemicals as specified below to states not party to the Chemical Weapons Convention shall continue to be restricted and will be allowed only against an export licence and a Government signed End-Use-Certificate, and in that case also exporters shall submit to the DGFT a copy of the bill of entry into the destination country within 30 days of delivery.
| SCOMET | Entry in | to CAS | ITC (HS) | ||
| Sl.No. | Entry | Name of Chemical | Schedule | number | code |
| 1 | 1C001 | Phosgene : ( Carbonyl dichloride | ) 3A01 | 75-44-5 | 28121100 |
| 2 | 1C002 | Cyanogen chloride [(CN) C1] | 3A02 | 506-77-4 | 28531000 |
| 3 | 1C003 | Hydrocyanic acid Chloropicrin: Trichloronitro- | 3A03 | 74-90-8 | 28111200 |
| 4 | 1C004 | Methane | 3A04 | 76-06-2 10025-87- | 29049100 |
| 5 | 1C005 | Phosphorus Oxychloride | 3B05 | 28121200 | |
| 6 | 1C006 | Phosphorus trichloride | 3B06 | 2125683 10026-13- | 28121300 |
| 7 | 1C007 | Phosphorous Pentachloride | 3B07 | 28121400 | |
| 8 | 1C008 | Trimethyl Phosphite | 3B08 | 121-45-9 | 29202300 |
| 9 | 1C009 | Triethyl Phosphite | 3B09 | 122-52-1 | 29202400 |
| 10 | 1C010 | Dimethyl Phosphite | 3B10 | 868-85-9 | 29202100 |
| 11 | 1C011 | Diethyl Phosphite | 3B11 | 762-04-9 10025-67- | 29202200 |
| 12 | 1C012 | Sulphur monochloride | 3B12 | 10545-99- | 28121500 |
| 13 | 1C013 | Sulphur dichloride | 3B13 | 28121600 | |
| 14 | 1C014 | Thionyl Chloride | 3B14 | 2125597 | 28121700 |
| 15 | 1C015 | Ethyldiethanolamine | 3B15 | 139-87-7 | 29221211 |
| 16 | 1C016 | Methyldiethanolamine | 3B16 | 105-59-9 | 29221212 |
| 17 | 1C017 | Triethanolamine Appendix 3 – SCOMET List | 3B17 | 102-71-6 | 29221300 |
1D Export of chemicals in this category is allowed to countries specified in Table 1 without an export licence subject to the condition that the exporter shall notify the Department of Chemicals & Petrochemicals, Ministry of External Affairs (D&ISA) and the DGFT within 30 days of such export in the prescribed format (Aayat Niryat Form) along with the End-Use Certificate and submit to the DGFT a copy of the bill of entry into the destination country within 30 days of delivery.
Export of chemicals in this category to other countries shall be restricted and will be allowed only against an export licence, and in that case the exporter shall submit to the DGFT a copy of the bill of entry into the destination country within 30 days of delivery.
SCOMET CAS
Sl.No. Name of Chemical
Entry Number
| 1 | 1D001 | 2-Chloroethanol | 107-07-3 |
| 2 | 1D002 | 3-Hydroxy-1-methylpiperidine | 3554-74-3 |
| 3 | 1D003 | 3-Quinuclidone | 3731-38-2 |
| 4 | 1D004 | Ammonium bifluoride | 1341-49-7 |
| 5 | 1D005 | Diethylaminoethanol | 100-37-8 |
| 6 | 1D006 | Diisopropylamine | 108-18-9 |
| 7 | 1D007 | Dimethylamine | 124-40-3 |
| 8 | 1D008 | Dimethylamine hydrochloride | 506-59-2 |
| 9 | 1D009 | Hydrogen fluoride | 7664-39-3 |
| 10 | 1D010 | Methyl benzilate | 76-89-1 |
| 11 | 1D011 | O,O-Diethyl phosphorothioate | 2465-65-8 |
| 12 | 1D012 | O,O-Diethyl phosphorodithioate | 298-06-6 |
| 13 | 1D013 | Pinacolone | 75-97-8 |
| 14 | 1D014 | Phosphorus pentasulphide | 1314-80-3 |
| 15 | 1D015 | Potassium bifluoride | 7789-23-3 |
| 16 | 1D016 | Potassium cyanide | 151-50-8 |
| 17 | 1D017 | Potassium fluoride | 7789-23-3 |
| 18 | 1D018 | Sodium bifluoride | 1333-83-1 |
| 19 | 1D019 | Sodium cyanide | 143-33-9 |
| 20 | 1D020 | Sodium fluoride | 7681-49-4 |
| 21 | 1D021 | Sodium hexafluorosilicate | 16893-85-9 |
| 22 | 1D022 | Sodium sulphide | 1313-82-2 |
| 23 | 1D023 | Triethanolamine hydrochloride | 637-39-8 |
| 24 | 1D024 | Triisopropyl phosphite | 116-17-6 |
| 25 | 1D025 | Diethylamine Table 1 | 109-89-7 |
Argentina, Australia, Austria, Belgium, Bulgaria, Canada, Croatia, Republic of Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Japan, Republic of Korea, Latvia, Lithuania, Luxembourg, Malta, Mexico, Netherlands, New Zealand, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland, Turkey, Ukraine, United Kingdom, United States.
Appendix 3 – SCOMET List
Technical note to Category 1:
Chemicals are listed by name, Chemical Abstract Service (CAS) number and CWC Schedule (where applicable). Chemicals of the same structural formula (e.g., hydrates) are controlled regardless of name or CAS number. CAS numbers are shown to assist in identifying whether a particular chemical or mixture is controlled, irrespective of nomenclature. However, CAS numbers cannot be used as unique identifiers in all situations because some forms of the listed chemical have different CAS numbers, and mixtures containing a listed chemical may also have different CAS numbers.
Appendix 3 – SCOMET List
Category 2 Micro-organisms, toxins
2A Bacteria (including Rickettsials), whether natural, enhanced or modified, either in the form of isolated live cultures or as material including living material which has been deliberately inoculated or contaminated with such cultures for the following:
2A001 Bacillus anthracis
2A002 Bordetella bronchoseptica
2A003 Brucella abortus
2A004 Brucella melitensis
2A005 Brucella suis
2A006 Chlamydia psittaci (Chlamydophila psittaci)
2A007 Clostridium botulinum
2A008 Clostridium perfringes, epsilon toxin producing types
Note: Limiting this control to epsilon toxin-producing strains of Clostridium perfringens therefore exempts from control the transfer of other Clostridium perfringens strains to be used as positive control cultures for food testing and quality control. 2A009 Corynebacterium diphtheriae
2A010 Francisella tularensis
2A011 Klebsiella pneumoniae
2A012 Legionlla pneumophila
2A013 Leptospira interrogans - all serotypes reported in India 2A014 Mycobacterium bovis
2A015 Mycobacterium tuberculosis
2A016 Mycoplasma mycoides - var mycoides
2A017 Mycoplasma mycoides - var Capri
2A018 Neisseria meningitidis
2A019 Paseturella multicoda type B
2A020 Burkholderia mallei (Pseudomonas mallei)
2A021 Burkholderia pseudomallei (Pseudomonas pseudomallei)
2A022 Salmonella paratyphi
2A023 Shigella dysenteriae
2A024 Staphylococcus aureus
2A025 Streptococcus pneumoniae
2A026 (Reserved)
2A027 Vibrio cholera
2A028 Yersinia pestis
2A029 Shiga toxin producing Escherichia coli (STEC) of serogroups O26, O45, O103, O104, O111, O121, O145, O157, and other shiga toxin producing serogroups
Note: Shiga toxin producing Escherichia (EHEC coli (STEC) includes inter alia
enterohaemorrhagic E. coli), verotoxin producing E. coli (VTEC) or verocytotoxin producing E. coli (VTEC).
2A030 Mycoplasma capricolum subspecies capripneumoniae (‘strain F38’)
2A031 Salmonella enterica subspecies enterica serovar Typhi (Salmonella typhi) 2A032 Clostridium argentinense (formerly known as Clostridium botulinum Type G), botulinum neurotoxin producing strains
2A033 Clostridium baratii, botulinum neurotoxin producing strains 2A034 Clostridium butyricum, botulinum neurotoxin producing strains
Appendix 3 – SCOMET List
2A035 Coxiella burnetii
2A036 Mycoplasma mycoides subspecies mycoides SC (small colony)
2A037 Rickettsia rickettsii
2A038 Rickettsia quintana
2A039 Rickettsia prowazekii
2B Fungi, whether natural, enhanced or modified, either in the form of isolated live cultures or as material including living material which has been deliberately inoculated or contaminated with such cultures for the following:
2B001 Blastomyces dermatitidis
2B002 Coccidiodes immitis
2B003 Histoplasma capulatum
2B004 Nocardia asteroides
2B005 Paracoccidioides braziliensis
2B006 Coccidiodes posadasii
2B007 Pneumocystis carinii
2C Parasites, whether natural, enhanced or modified, either in the form of isolated live cultures or as material including living material which has been deliberately inoculated or contaminated with such cultures for the following:
2C001 Entamoeba histolytica
2C002 Babesia microti
2C003 Babesia divergens
2C004 Blostidium coli
2C005 Cryptosporidium spp.
2C006 Leishmania species
2C007 Naegleria australiensis
2C008 Naegleria fowleri
2C009 Plasmodium falciparum
2C010 (Reserved)
2C011 Schistosoma mansoni
2C012 Schistosoma japonicum
2C013 Schistosoma hemotobium
2C014 Toxoplasma gondii
2C015 Trichinella spiralis
2C016 Trypanosoma bruiei
2D Viruses, whether natural, enhanced or modified, either in the form of isolated live cultures or as material including living material which has been deliberately inoculated or contaminated with such cultures for the following:
2D001 African Horse Sickness virus
2D002 African Swine Fever virus
2D003 Avian influenza virus
Note: This includes only those Avian influenza viruses of high pathogenicity as
defined by the World Organization for Animal Health (OIE), the European Union
(EU), or competent national regulatory bodies.
2D004 Blue tongue virus
2D005 Camel pox virus
2D006 Chikungunya virus
2D007 Crimean-Congo hemorrhagic fever virus
2D008 Dengue virus
Appendix 3 – SCOMET List
2D009 Eastern equine encephalitis virus
2D010 Ebolavirus: all members of the Ebolavirus genus
2D011 Encephalomyocarditis virus (EMC)
2D012 Foot and Mouth Disease virus (all serotypes and subtypes)
2D013 Guanarito virus
2D014 Goatpox virus
2D015 Hantaan virus
2D016 Herpes virus simiae (monkey B virus)
2D017 Herpes ateles, Herpes saimiri
2D018 HIV- 1 & HIV-2 and other strains of SIV
2D019 Classical swine fever virus (Hog cholera virus)
2D020 Human T-cell Leukemia virus
2D021 Junin virus
2D022 Japanese encephalitis virus
2D023 Kyasanur Forest Disease virus
2D024 Korean hemorrhagic fever virus
2D025 Lymphocytic choriomeningitis virus (LCM)
2D026 Lassa virus
2D027 Marburgvirus: all members of the Marburgvirus genus
2D028 Murray valley encephalitis virus
2D029 Machupo virus
2D030 Mason-pfizer monkey virus
2D031 Monkey pox virus
2D032 Newcastle disease virus
2D033 Omsk hemorrhagic fever virus
2D034 Peste des petits ruminant virus
2D035 Teschen disease virus (Porcine entero virus type 1)
2D036 Powassan virus
2D037 Rabies virus and other members of the Lyssavirus genus
2D038 Respiratory syncitial virus
2D039 Rift Valley Fever virus
2D040 Rinderpest virus
2D041 Sabia virus
2D042 Sheeppox virus
2D043 Sin Nombre virus
2D044 Smallpox virus
2D045 St.Louis encephalitis virus
2D046 Swine vesicular disease virus
2D047 Tick-borne encephalitis virus (Far Eastern subtype)
2D048 (Reserved)
2D049 Variola virus
2D050 Venezuelan equine encephalitis virus
2D051 Vesicular stomatitis virus
2D052 Western equine encephalitis virus
2D053 Yellow fever virus
2D054 Andes virus
2D055 Chapare virus
Appendix 3 – SCOMET List
2D056 Choclo virus
2D057 Dobrava-Belgrade virus
2D058 Suid herpesvirus 1 (Pseudorabies virus; Aujeszky's disease)
2D059 Hendra virus (Equine morbillivirus)
2D060 Laguna Negra virus
2D061 Louping ill virus
2D062 Lujo virus
2D063 Lumpy skin disease virus
2D064 (Reserved)
2D065 Nipah virus
2D066 Oropouche virus
2D067 (Reserved)
2D068 Rocio virus
2D069 Seoul virus
2D070 Severe acute respiratory syndrome-related coronavirus (SARS-related coronavirus) 2D071 Reconstructed 1918 influenza virus
2E [Reserved]
2F Toxins
2F001 Abrin
2F002 Aflatoxins
2F003 Anatoxins
2F004 Botulinum toxins
Note: Excluding botulinum toxins in product form meeting all of the following criteria:
a. are pharmaceutical formulations designed for testing and human administration in the treatment of medical conditions;
b. are pre-packaged for distribution as clinical or medical products; and
c. are authorised by a state authority to be marketed as clinical or medical products 2F005 Bungarotoxins
2F006 Clostridium perfringens alpha, beta 1, beta 2, epsilon and iota toxins 2F007 Corynebacterium diphtheriae toxins
2F008 Cyanginosins (Microcystins) (Microcystic aeuginosa)
2F009 Staphylococcus aureus enterotoxins, hemolysin alpha toxin, and toxic shock syndrome toxin (formerly known as Staphylococcus enterotoxin F)
2F010 Neurotoxin (Shigella dysenteriae)
2F011 (Reserved)
2F012 Shiga toxins (shiga-like toxins, verotoxins, and verocytotoxins)
2F013 (Reserved)
2F014 Trichothecene mycotoxins
2F015 Tetanus toxin (clostridium tetani)
2F016 Tetrodotoxin (Spheroides rufripes)
2F017 Verrucologen (M. verrucadia)
2F018 Cholera toxin
Appendix 3 – SCOMET List
2F019 Conotoxins
Note: Excluding conotoxins in product form meeting all of the following criteria:
a. are pharmaceutical formulations designed for testing and human administration in the treatment of medical conditions;
| b. are pre-packaged for distribution as clinical or medical products; are authorised by a state authority to be marketed as clinical or medical products | and | |
| 2F020 2F021 2F022 2F023 2F024 2F025 2F026 | Diacetoxyscirpenol toxin HT-2 toxin Modeccin toxin T-2 mycotoxin Verotoxin and shiga-like ribosome inactivating proteins Viscum Album Lectin 1 (Viscumin) Volkensin toxin |
2G Plant pathogens
2G001 Bemisia tabaci
2G002 Colletotrichum kahawae (Colletotrichum coffeanum var. virulans)
2G003 Claviceps purpurea
2G004 Dothistroma pini (Scirrhia pini)
2G005 Erwinia amylovora
2G006 Frankliniella occidentalis
2G007 Microcyclus ulei (syn. Dothidella ulei)
2G008 Peronospora hyoscyami f.sp. tabacina
2G009 Phytophthora infestans
2G010 Puccinia graminis ssp. graminis var. graminis / Puccinia graminis ssp. graminis var. stakmanii (Puccinia graminis [syn. Puccinia graminis f. sp. tritici])
2G011 Puccinia erianthi
2G012 Puccinia striiformiis f. sp. tritici (Puccinia glumarum)
2G013 Magnaporthe oryzae (Pyricularia oryzae)
2G014 Ralstonia solanacearum
2G015 Peronospora hyscyami de Bary
2G016 (Reserved)
2G017 Sugar cane Fiji disease virus
2G018 Sclerotinia sclerotiorum
2G019 Tilletia indica
2G020 Thrips palmi
2G021 Ustilago Maydis
2G022 Xanthomonas albilineans
2G023 Xanthomonas axonopodis pv. citri (Xanthomonas campestris pv. citri A) [Xanthomonas campestris pv. citri]
2G024 Xanthomonas oryzae pv. oryzae (Pseudomonas campestris pv. oryzae)
2G025 Clavibacter michiganensis subsp. sepedonicus (Corynebacterium michiganensis subsp. sepedonicum or Corynebacterium sepedonicum)
2G026 Cochliobolus miyabeanus (Helminthosporium oryzae)
2G027 Andean potato latent virus (Potato Andean latent tymovirus)
2G028 Potato spindle tuber viroid
2G029 Thecaphora solani
Appendix 3 – SCOMET List
2G030 Synchytrium endobioticum
2G031 Sclerophthora rayssiae var. zeae
2G032 Peronosclerospora philippinensis (Peronosclerospora sacchari)
2H Genetically Modified Organisms
2H001 a. Genetic elements that contain nucleic acid sequences associated with the pathogenicity or toxicity of any of the organisms or toxins listed in Category 2A, 2B, 2C, 2D, 2F and 2G
b. Genetically-modified organisms that contain nucleic acid sequences associated with the pathogenicity or toxicity of any of the organisms or toxins listed in Category 2A, 2B, 2C, 2D, 2F and 2G.,
Technical note:
(1) Genetically-modified organisms includes organisms in which the genetic material (nucleic acid sequences) has been altered in a way that does not occur naturally by mating and/or natural recombination, and encompasses those produced artificially in whole or in part.
(2) Genetic elements include inter alia chromosomes, genomes, plasmids, transposons, and vectors whether genetically modified or unmodified, or chemically synthesized in whole or in part.
(3) Nucleic acid sequences associated with the pathogenicity or toxicity of any of the organisms or toxins in the list means any sequence specific to the relevant listed organism or toxin:
(i) that in itself or through its transcribed or translated products represents a significant hazard to human, animal or plant health; or
(ii) that is known to enhance the ability of a listed organism, or any other organism into which it may be inserted or otherwise integrated, to cause serious harm to human, animal or plant health.
Appendix 3 – SCOMET List
Category 3 Materials, Materials Processing Equipment and related technologies 3A Materials
3A1 Special Materials
3A101 Zirconium, beryllium, magnesium, and alloys of these in particle size less than 60 µm 3A102 Maraging steel in any form in which any linear dimension exceeds 75 mm, or in the form of sheet,
plate or tubing with a wall or plate thickness equal or less than 5 mm.
3A103 Tungsten , molybdenum, and alloys of those metals in particulate form and a particle size of 50 x10- 6 m (50 µm) or less; ”
3A104 Germanium
3A105 Gallium
3A106 Indium
3A107 Titanium-stabilised Duplex Stainless Steel (Ti-DSS)
| 3A108 | Aluminium alloys in any form ‘capable of acquiring’ an ultimate tensile strength of 460 MPa or more at 293 K (20 degrees C) Note: The phrase ‘capable of acquiring’ encompasses alloys before or after heat treatment |
3A109 Bismuth having a purity of 99.99% or greater by weight and containing less than 10 parts per million by weight of silver
3A110 Calcium containing less than 1000 parts per million by weight of metallic impurities other than
magnesium and containing less than 10 parts per million by weight of Boron
3A111 Chlorine trifluoride (ClF3)
3A112 Magnesium containing less than 200 parts per million by weight of metallic impurities other than
calcium and containing less than 10 parts per million by weight of boron
3A113 (a) Tungsten, tungsten carbide, and alloys containing more than 90% tungsten by weight in forms with a hollow cylindrical symmetry (including cylinder segments) with an inside diameter between 100 and 300 mm and a mass greater than 20 kg.
(b) Tungsten materials in the solid form usable for the fabrication of missile components in complete rocket systems of 5A and unmanned aerial vehicles of 5B, having all of the following:
1. Any of the following material compositions:
ii. Tungsten and alloys containing 97% by weight or more of tungsten;
iii. Copper infiltrated tungsten containing 80% by weight or more of tungsten; or
iv. Silver infiltrated tungsten containing 80% by weight or more of tungsten; and
2. Able to be machined to any of the following products:
i. Cylinders having a diameter of 120 mm or greater and a length of 50 mm or greater;
ii. Tubes having an inner diameter of 65 mm or greater and a wall thickness of 25 mm or greater and a length of 50 mm or greater; or
iii. Blocks having a size of 120 mm x 120 mm x 50 mm or greater.
3A114 a. Nickel powder of purity 99.0% or greater by weight; and having a mean particle size of less than 10 µm measured by the ASTM B 330 standard;
b. Porous nickel metal produced from the nickel powder specified above
Appendix 3 – SCOMET List
3A115 Natural boron, boron carbide or metal borides having a boron purity of 85% or more.
3A116 Fibrous or filamentary materials, and prepregs, as follows:
a. Carbon or aramid fibrous or filamentary materials having ‘specific modulus’ of
12.7 x 106 m or greater; or ‘specific tensile strength’ of 23.5 x 104 m or greater;
b. Glass fibrous or filamentary materials having ‘specific modulus’ of 3.18 x 106 m or greater;
and ‘specific tensile strength’ of 7.62 x 104 m or greater;
c. Thermoset resin impregnated continuous yarns, rovings, tows or tapes with a width of 15 mm or less (prepregs), made from carbon or glass fibrous or filamentary materials specified in (a) or (b) above.
3A117 Carbon - carbon composites.
3A118 Titanium alloys having both of the following characteristics:
a. Capable of’ an ultimate tensile strength of 900 MPa or more at 293 K (20 degrees C); and
b. In the form of tubes or cylindrical solid forms (including forgings) with an outside diameter of more than 75 mm.
Technical note: The phrase ‘capable of’ encompasses titanium alloys before or after heat treatment 3A119 Rhenium, and alloys containing 90% by weight or more rhenium; and alloys of rhenium and tungsten containing 90% by weight or more of any combination of rhenium and tungsten, have both of the following characteristics:
a. In forms with a hollow cylindrical symmetry (including cylinder segments) with an inside diameter between 100 and 300 mm; and
b. A mass greater than 20kg
3A120 Technology and Software
Technology and software for the development, production or use of items specified in 3A1 or 3A4 3A2 Structural Materials
3A201 Structural materials such as:
a. Composite structures, laminates, resin impregnated fibre prepregs and metal coated fibre preforms made either with an organic matrix or metal matrix utilizing fibrous or filamentary reinforcements, and manufactures thereof, specially designed for use in rocket systems (including ballistic missile systems, space launch vehicles and sounding rockets), unmanned
aerial vehicles and cruise missiles and subsystems thereof;
b. Resaturated pyrolized (i.e. Carbon-Carbon) materials specially designed for rocket systems (including ballistic missile systems, space launch vehicles and sounding rockets),
unmanned aerial vehicles and cruise missiles;
c. Fine grain re-crystalised bulk graphites and pyrolytic or fibrous reinforced graphites usable
for rocket nozzles and re-entry vehicles nose tips;
d. Ceramic composite materials (dielectric constant less than 6 at any frequency from 100
MHz to 100 GHz) for use in missile radomes;
e. Materials and coatings for reduced radar reflectivity;
f. Bulk machinable silicon-carbide reinforced unfired ceramic usable in re-entry vehicles nose tips.
g. Reinforced silicon-carbide ceramic composites usable for nose tips, re-entry vehicles, nozzle flaps, usable in complete rocket systems of 5A and complete unmanned aerial vehicles of 5B .
h. Bulk machinable ceramic composite materials consisting of an 'Ultra High Temperature Ceramic (UHTC)' matrix with a melting point equal to or greater than 3000°C and reinforced with fibres or filaments, usable for missile components (such as nose-tips, reentry vehicles, leading edges, jet vanes, control surfaces or rocket motor throat inserts) in the systems specified in 5A and 5B.
Note:
Appendix 3 – SCOMET List
Item 3A201.h does not control 'Ultra High Temperature Ceramic (UHTC)' materials in non-composite form.
Technical Note:
'Ultra High Temperature Ceramics (UHTC)' includes:
1. Titanium diboride (TiB2);
2. Zirconium diboride (ZrB2);
3. Niobium diboride (NbB2);
4. Hafnium diboride (HfB2);
5. Tantalum diboride (TaB2);
6. Titanium carbide (TiC);
7. Zirconium carbide (ZrC);
8. Niobium carbide (NbC);
9. Hafnium carbide (HfC);
10. Tantalum carbide (TaC).”
3A3 Rocket propellants and constituent chemicals:
3A301 Fuel substances as follows:
a. Hydrazine (CAS 302-01-2) with a concentration of more than 70%
b. Hydrazine derivatives as follows:
1. Monomethylhydrazine (MMH) (CAS 60-34-4);
2. Unsymmetrical dimethylhydrazine (UDMH) (CAS 57-14-7);
3. Hydrazine mononitrate (CAS 13464-97-6);
4. Trimethylhydrazine (CAS 1741-01-1);
5. Tetramethylhydrazine (CAS 6415-12-9);
6. N, N diallylhydrazine (CAS 5164-11-4);
7. Allylhydrazine (CAS 7422-78-8);
8. Ethylene dihydrazine;
9. Monomethylhydrazine dinitrate;
10. Unsymmetrical dimethylhydrazine nitrate;
11. Hydrazinium azide (CAS 14546-44-2);
12. Dimethylhydrazinium azide;
13. Hydrazinium dinitrate (CAS 13464-98-7);
14. Diimido oxalic acid dihydrazine (CAS 3457-37-2);
15. 2-hydroxyethylhydrazine nitrate (HEHN);
16. Hydrazinium perchlorate (CAS 27978-54-7);
17. Hydrazinium diperchlorate (CAS 13812-39-0);
18. Methylhydrazine nitrate (MHN) (CAS 29674-96-2);
19. Diethylhydrazine nitrate (DEHN);
20. 3, 6-dihydrazino tetrazine nitrate (DHTN);
Technical note: 3, 6-dihydrazino tetrazine nitrate is also referred to as 1, 4-dihydrazine nitrate
c. Spherical or spheroidal aluminium powder (CAS 7429-90-5) in particle
size of less than 200 x 10-6 m (200 µm) and an aluminium content of 97% by weight or more, if at least 10% of the total weight is made up of particles of less than 63 µm, according to ISO 2591-1:1988 or national equivalents;
Appendix 3 – SCOMET List
Technical Note: A particle size of 63 µm (ISO R-565) corresponds to 250 mesh (Tyler) or 230 mesh (ASTM standard E-11).
d. Hydrazine replacement fuels as follows:
1.2-Dimethylaminoethylazide (DMAZ) (CAS 86147-04-8)”;
3A302 Metal fuels containing any of the following: Zirconium(CAS 7440-67-7), beryllium(CAS 7440-41-
7), magnesium, titanium, tungsten, boron and boron alloys, zinc, and alloys of magnesium(CAS 7439-95-4);
3A303 Polymeric substances, as follows:
a. Carboxy-terminated polybutadiene (including carboxyl – terminated polybutadiene) (CTPB);
b. Hydroxy Terminated Polybutadiene (including Hydroxyl Terminated polybutadiene) (HTPB) (CAS 69102-90-5)
c. Glycidyl azide polymer (GAP);
d. Polybutadiene - Acrylic Acid (PBAA);
e. Polybutadiene - Acrylic Acid - Acrylonitrile (PBAN);
f. Polytetrahydrofuran polyethylene glycol (TPEG).
g. Polyglycidyl nitrate (PGN or poly-GLYN) (CAS 27814-48- 8).
Technical Note:
Polytetrahydrofuran polyethylene glycol (TPEG) is a block co-polymer of poly 1, 4- Butanediol (CAS 110-63-4) and polyethylene glycol (PEG) (CAS 25322-68-3).”
3A304 Composite propellants and composite modified double base propellants;
3A305 High energy density materials such as boron slurry;
3A306 Oxidizers/fuels - Perchlorates, chlorates or chromates mixed with powdered metals or other high energy fuel components; Dinitrogen trioxide, Nitrogen dioxide / Dinitrogen tetroxide, Mixed Oxides of Nitrogen (MON), Dinitrogen pentoxide, Inhibited red fuming nitric acid (IRFNA) (CAS 8007-58-7), Ammonium perchlorate (CAS 7790-98-9), Ammonium Dinitramide (ADN) (CAS 140456-78-6), Hydrazinium Nitroformate (HNF), 2,4,6,8,10,12- Hexanitrohexaazaisowurtzitane (CL-20) (CAS 135285-90-4), Compounds composed of fluorine and one more of other halogens, oxygen or nitrogen.
3A307 Bonding agents - Tris (1-2 (2-methyl)) aziridinyl phosphine oxide (MAPO)(CAS 57-39- 6), Trimesoyl-1-(2-ethyl) aziridene (HX-868, BITA)(CAS 7722-73-8), Tepanol (HX- 878)(CAS 68412- 46-4), Tepan (HX-879) reaction product of tetraethlylenepentamine and acrylonitrile (CAS 68412- 45-3), and Polyfunctional aziridine amides with isophthalic, trimesic, isocyanuric, or trimethyladipic backbone also having a 2-methyl or 2-ethyl aziridine group including 1,1′-Isophthaloyl-bis(2- methylaziridene (CAS 7652-64-4), (HX-752, HX-874, and HX-877);
3A308 Curing agents and reaction catalysts - Triphyenyl bismuth (TPB)(CAS 603-33-8);
3A309 Burning rate modifiers –
a. Carboranes, decaboranes, pentaboranes and derivatives thereof;
b. Ferrocene derivatives, as follows:
1. Catocene (CAS 37206-42-1);
2. Ethyl ferrocene;
3. n-Propyl ferrocene (CAS 1273-92-3) / iso-propyl ferrocene (CAS 12126-81-7)
4. n-Butyl ferrocene(CAS 31904-29-7);
5. Pentyl ferrocene (CAS 1274-00-6);
6. Dicyclopentyl ferrocene(CAS 20773-28-8);
7. Dicyclohexyl ferrocene;
Appendix 3 – SCOMET List
8. Diethyl ferrocene;
9. Dipropyl ferrocene;
10. Dibutyl ferrocene(CAS 1274-08-4);
11. Dihexyl ferrocene (CAS 93894-59-8);
12. Acetyl ferrocenes;
13. Ferrocene Carboxylic acids;
14. Butacene;
c. Other ferrocene derivatives usable as rocket propellant burning rate modifiers.
3A310 Nitrate esters and nitrated plasticisers as follows:
a. Triethylene glycol dinitrate (TEGDN);
b. Trimethylolethane trinitrate (TMETN)(CAS 3032-55-1) ;
c. 1,2,4-butanetriol trinitrate (BTTN)(CAS 6659-60-5) ;
d. Diethylene glycol dinitrate (DEGDN);
e. 4,5 diazidomethyl-2-methyl-1,2,3-triazole (iso-DAMTR);
f. Nitratoethylnitramine (NENA) based plasticisers, as follows:
1. Methyl-NENA (CAS 17096-47-8);
2. Ethyl-NENA (CAS 85068-73-1);
3. Butyl-NENA (CAS 82486-82-6);
g. Dinitropropyl based plasticisers, as follows:
1. Bis (2,2-dinitropropyl) acetal (BDNPA) (CAS 5108-69-0);
2. Bis (2,2-dinitropropyl) formal (BDNPF) (CAS 5917-61-3).
3A311 Stabilisers as follows:
a. 2-Nitrodiphenylamine (CAS 119-75-5);
b. N-methyl-p-nitroaniline (CAS 100-15-2).
3A4 High explosives
3A401 High explosive substances or mixtures, containing more than 2 % by weight of any of the following:
a. Cyclotetramethylenetetranitramine (HMX ) (CAS 2691-41-0);
b. Cyclotrimethylenetrinitramine (RDX) (CAS 121-82-4);
c. Triaminotrinitrobenzene (TATB) (CAS 3058-38-6);
d. Aminodinitrobenzo-furoxan or 7-amino-4,6 nitrobenzofurazane-1-oxide (ADNBF) (CAS 97096-78-1);
e. 1,1-diamino-2,2-dinitroethylene (DADE or FOX7) (CAS 145250-81-3);
f. 2,4-dinitroimidazole (DNI) (CAS 5213-49-0);
g. Diaminoazoxyfurazan (DAAOF or DAAF) (CAS 78644-89-0);
h. Diaminotrinitrobenzene (DATB) (CAS 1630-08-6);
i. Dinitroglycoluril (DNGU or DINGU) (CAS 55510-04-8);
j. 2,6-Bis (picrylamino)-3,5-dinitropyridine (PYX) (CAS 38082-89-2);
k. 3,3′-diamino-2,2′,4,4′,6,6′-hexanitrobiphenyl or dipicramide (DIPAM) (CAS 17215-44-0);
l. Diaminoazofurazan (DAAzF) (CAS 78644-90-3);
m. 1,4,5,8-tetranitro-pyridazino[4,5-d] pyridazine (TNP) (CAS 229176-04-9);
n. Hexanitrostilbene (HNS) (CAS 20062-22-0); or
o. Any explosive with a crystal density greater than 1.8 g/cm3 and having a detonation velocity greater than 8000 m/s.
Note: License applications for the export of items at 3A401a and 3A401b will normally be denied.
3A5 Stealth materials
3A501 a. Materials for reduced observables such as radar reflectivity, ultraviolet/infrared signatures and acoustic signatures;
b. Devices, including made from non-stealth material, for reduced observables such as radar
reflectivity, ultraviolet/infrared signatures and acoustic signatures;
Appendix 3 – SCOMET List
3A502 Materials and coatings (including paints) specially designed for reduced or tailored reflectivity or emissivity in the microwave, infrared or ultraviolet spectra other than coatings (including paints) when specially used for thermal control of satellites.
3A503 Technology related to the development, production or use of items in 3A.
3B Materials processing and “production equipment”, related “technology” and specially designed components and accessories therefor.
3B001 Remote manipulators that provide mechanical translation of human operator actions by electrical, hydraulic or mechanical means and operating arm and terminal fixture that can be used to provide remote actions;
3B002 Multidirectional, multidimensional weaving and interlacing machines, including adapters and modification kits for weaving, interlacing or braiding fibres to fabricate composite structures except
textile machinery which has not been modified for rocket systems;
3B003 Equipment designed or modified for production of fibrous or filamentary materials as follows: converting polymeric substances; vapour deposition on heated filament substrates; wet spinning of refractory ceramics.
3B004 Equipment designed or modified for special fibre surface treatment or for producing prepregs and preforms, including rollers, tension stretchers, coating equipment, cutting equipment and clicker dies;
3B005 Chemical vapour deposition furnaces designed or modified for the densification of carboncarbon composites.
3B006 Pyrolytic deposition and densification equipment including:
a. Technology for producing pyrolytically derived materials formed on a mould, mandrel or other substrate from precursor gases.
b. Specially designed nozzles for the above process.
c. Equipment and process controls and specially designated software thereof, specially designed or modified for densification and pyrolysis of structural composite rocket nozzles and re-entry vehicle nose tips.
3B007 Production equipment usable for or specially designed or modified for production, handling, mixing, curing, casting, pressing, machining, extruding or acceptance testing of the solid or liquid rocket propellants or rocket propellant constituents and related technology.
3B008 Refrigeration units and equipment capable of cooling hydrogen or helium to -250 degrees Celsius (23K) or lower.
3B009 Continuous nitrators.
3B010 Dehydration presses.
3B011 Screw extruders usable for or specially designed or modified for high explosive extrusion.
3B012 Cutting machines for the sizing of extruded propellant.
3B013 Sweetie barrels (tumblers) 1.85 m or more in diameter and having over 227 kg product capacity;
3B014 Continuous mixers or batch mixers with provision for mixing under vacuum.
3B015 Fluid energy mills usable for grinding or milling any of the items in 3A3.
3B016 Metal powder production equipment usable for the production, in a controlled environment, of
spherical, spheroidal or atomised materials specified in 3A301.c. or 3A302
Note: This entry includes:
Appendix 3 – SCOMET List
a. Plasma generators (high frequency arc-jet) usable for obtaining sputtered or spherical metallic powders with organization of the process in an argon-water environment;
b. Electroburst equipment usable for obtaining sputtered or spherical metallic powders with
organization of the process in an argon-water environment;
c. Equipment usable for the production of spherical aluminium powders by powdering a melt in an inert medium (e.g. nitrogen).
3B017 Sputter ion pumps
| 3B018 3B019 | Technical data (including processing conditions) and procedures for the regulation of temperature, pressure or atmosphere in autoclaves or hydroclaves when used for the production of composites or partially processed composites. Software specially designed or modified for the use of equipment for the production and handling of materials specified in 3A |
3B020 Technology for the development, production or use of items in 3B 3C [Reserved]
3D Chemical and biomaterial manufacturing and handling equipment and facilities:
3D001
(1) Reaction Vessels, Reactors or Agitators
(i) Reaction vessels or reactors, with or without agitators, with total internal (geometric) volume greater than 0.1 m³ (100 l) and less than 20 m³ (20000 l), where all surfaces that come in direct contact with the chemical(s) being processed or contained are made from the following materials:
a. nickel or alloys with more than 40% nickel by weight;
b. alloys with more than 25% nickel and 20% chromium by weight;
c. fluoropolymers (polymeric or elastomeric materials with more than 35% fluorine by weight);
d. glass or glass-lined (including vitrified or enamelled coating);
e. tantalum or tantalum alloys;
f. titanium or titanium alloys;
g. zirconium or zirconium alloys; or
h. niobium (columbium) or niobium alloys.
(ii) Agitators designed for use in the above-mentioned reaction vessels or reactors; and impellers, blades or shafts designed for such agitators where all surfaces of the agitator that come in direct contact with the chemical(s) being processed or contained are made from any of the following materials:
a. nickel or alloys with more than 40% nickel by weight;
b. alloys with more than 25% nickel and 20% chromium by weight;
c. fluoropolymers (polymeric or elastomeric materials with more than 35% fluorine by weight);
d. glass or glass-lined (including vitrified or enamelled coating);
e. tantalum or tantalum alloys;
f. titanium or titanium alloys;
g. zirconium or zirconium alloys; or
h. niobium (columbium) or niobium alloys.
(2) Storage Tanks, Containers or Receivers
Storage tanks, containers or receivers with a total internal (geometric) volume greater than 0.1 m³ (100
l) where all surfaces that come in direct contact with the chemical(s) being processed or contained are made from the following materials:
a. nickel or alloys with more than 40% nickel by weight;
Appendix 3 – SCOMET List
b. alloys with more than 25% nickel and 20% chromium by weight;
c. fluoropolymers (polymeric or elastomeric materials with more than 35% fluorine by weight);
d. glass or glass-lined (including vitrified or enamelled coating);
e. tantalum or tantalum alloys;
f. titanium or titanium alloys;
g. zirconium or zirconium alloys; or
h. niobium (columbium) or niobium alloys.
(3) Heat Exchangers or Condensers
Heat exchangers or condensers with a heat transfer surface area of greater than 0.15 m², and less than 20 m²; and tubes, plates, coils or blocks (cores) designed for such heat exchangers or condensers, where all surfaces that come in direct contact with the chemical(s) being processed are made from the following materials:
a. nickel or alloys with more than 40% nickel by weight;
b. alloys with more than 25% nickel and 20% chromium by weight;
c. fluoropolymers (polymeric or elastomeric materials with more than 35% fluorine by weight);
d. glass or glass-lined (including vitrified or enamelled coating);
e. graphite or carbon-graphite;
f. tantalum or tantalum alloys;
g. titanium or titanium alloys;
h. zirconium or zirconium alloys;
i. silicon carbide;
j. titanium carbide; or
k. niobium (columbium) or niobium alloys.
Technical note: carbon-graphite is a composition consisting of amorphous carbon and graphite, in which the graphite content is eight percent or more by weight.
(4) Distillation or Absorption Columns
Distillation or absorption columns of internal diameter greater than 0.1 m; and liquid distributors, vapour distributors or liquid collectors designed for such distillation or absorption columns, where all surfaces that come in direct contact with the chemical(s) being processed are made from the following materials:
a. nickel or alloys with more than 40% nickel by weight;
b. alloys with more than 25% nickel and 20% chromium by weight;
c. fluoropolymers (polymeric or elastomeric materials with more than 35% fluorine by weight);
d. glass or glass-lined (including vitrified or enamelled coating);
e. graphite or carbon-graphite;
f. tantalum or tantalum alloys;
g. titanium or titanium alloys;
h. zirconium or zirconium alloys; or
i. niobium (columbium) or niobium alloys.
Technical note: carbon-graphite is a composition consisting of amorphous carbon and graphite, in which the graphite content is eight percent or more by weight.
(5) Filling Equipment
Remotely operated filling equipment in which all surfaces that come in direct contact with the chemical(s) being processed are made from the following materials:
a. nickel or alloys with more than 40% nickel by weight; or
b. alloys with more than 25% nickel and 20% chromium by weight.
(6) Valves
(i) Valves, having both of the following:
Appendix 3 – SCOMET List
a. A nominal size greater than 1.0 cm (3/8"), and
b. All surfaces that come in direct contact with the chemical(s) being produced, processed, or contained are made from the materials of construction in Technical Note 1 of this entry
(ii) Valves, not already identified in 3D001(6)(i), having all of the following:
a. A nominal size equal to or greater than 2.54 cm (1") and equal to or less than 10.16 cm (4")
b. Casings (valve bodies) or preformed casing liners,
c. A closure element designed to be interchangeable, and
d. All surfaces of the casing (valve body) or preformed case liner that come in direct contact with the chemical(s) being produced, processed, or contained are made from the materials of construction in Technical Note 1 of this entry
(iii) Components, as follows:
a. Casings (valve bodies) designed for valves in paragraphs 6.a.or 6.b., in which all surfaces that come in direct contact with the chemical(s) being produced, processed, or contained are made from the materials of construction in Technical Note 1 of this entry;
b. Preformed casing liners designed for valves in paragraphs 6.a.or 6.b., in which all surfaces that come in direct contact with the chemical(s) being produced, processed, or contained are made from the materials of construction in Technical Note 1 of this entry.
Technical Note 1. Materials of construction for valves include any of the following:
a. nickel or alloys with more than 40% nickel by weight;
b. alloys with more than 25% nickel and 20% chromium by weight;
c. fluoropolymers (polymeric or elastomeric materials with more than 35% fluorine by weight);
d. glass or glass-lined (including vitrified or enamelled coating);
e. tantalum or tantalum alloys;
f. titanium or titanium alloys;
g. zirconium or zirconium alloys;
h. niobium (columbium) or niobium alloys; or
i. ceramic materials as follows:
1. silicon carbide with a purity of 80% or more by weight;
2. aluminum oxide (alumina) with a purity of 99.9% or more by weight;
3. zirconium oxide (zirconia).
Technical Note 2. The 'nominal size' is defined as the smaller of the inlet and outlet port diameters.
(7) Multi-Walled Piping
Multi-walled piping incorporating a leak detection port, in which all surfaces that come in direct contact with the chemical(s) being processed or contained are made from the following materials:
a. nickel or alloys with more than 40% nickel by weight;
b. alloys with more than 25% nickel and 20% chromium by weight;
c. fluoropolymers (polymeric or elastomeric materials with more than 35% fluorine by weight);
d. glass or glass-lined (including vitrified or enamelled coating);
e. graphite or carbon-graphite;
f. tantalum or tantalum alloys;
g. titanium or titanium alloys;
h. zirconium or zirconium alloys; or
i. (columbium) or niobium alloys.
Technical note: carbon-graphite is a composition consisting of amorphous carbon and graphite, in which the graphite-content is eight percent or more by weight.
(8) Pumps
Multiple-seal and seal-less pumps with manufacturer's specified maximum flow-rate greater than 0.6 m3/h, or vacuum pumps with manufacturer's specified maximum flow-rate greater than 5 m³/h (under standard temperature (273 K (0o C)) and pressure (101.3 kPa) conditions), and casings (pump bodies), Appendix 3 – SCOMET List
preformed casing liners, impellers, rotors or jet pump nozzles designed for such pumps, in which all surfaces that come into direct contact with the chemical(s) being processed are made from any of the following materials:
a. nickel or alloys with more than 40% nickel by weight;
b. alloys with more than 25% nickel and 20% chromium by weight;
c. fluoropolymers (polymeric or elastomeric materials with more than 35% fluorine by weight);
d. glass or glass-lined (including vitrified or enamelled coating);
e. graphite or carbon-graphite;
f. tantalum or tantalum alloys;
g. titanium or titanium alloys;
h. zirconium or zirconium alloys;
i. ceramics;
j. ferrosilicon (high silicon iron alloys); or
k. niobium (columbium) or niobium alloys.
Technical note 1: carbon-graphite is a composition consisting of amorphous carbon and graphite, in which the graphite content is eight percent or more by weight.
Technical note 2: : The seals referred to in this control come into direct contact with the chemical(s) being processed (or are designed to), and provide a sealing function where a rotary or reciprocating drive shaft passes through a pump body.
(9) Incinerators
Incinerators designed to destroy CW agents, Category 1 chemicals or chemical munitions, having specially designed waste supply systems, special handling facilities, and an average combustion chamber temperature greater than 1000o C, in which all surfaces in the waste supply system that come into direct contact with the waste products are made from or lined with the following materials:
a. nickel or alloys with more than 40% nickel by weight;
b. alloys with more than 25% nickel and 20% chromium by weight; or ceramics.
Notes to 3D001:
Technical note: For the listed materials in 3D001, the term 'alloy' when not accompanied by a specific elemental concentration is understood as identifying those alloys where the identified metal is present in a higher percentage by weight than any other element.
Note 1. The objective of these controls should not be defeated by the transfer of any non-controlled item containing one or more controlled components where the controlled component or components are the principal element of the item and can feasibly be removed or used for other purposes.
N.B. In judging whether the controlled component or components are to be considered the principal element, the licensing authority should weigh the factors of quantity, value, and technological knowhow involved and other special circumstances which might establish the controlled component or components as the principal element of the item being procured.
Note 2. The objective of these controls should not be defeated by the transfer of a whole plant, on any scale, which has been designed to produce any CW agent or Category 1 chemical.
Note 3. The materials used for gaskets, packing, seals, screws, washers or other materials performing a sealing function do not determine the status of control of the items listed below, provided that such components are designed to be interchangeable.
Note 4: The controls in 3D001 do not apply to equipment which is specially designed for use in civil applications (for example food processing, pulp and paper processing, or water purification, etc) and is, by the nature of its design, inappropriate for use in storing, processing, producing or conducting and controlling the flow of chemical warfare agents or any of the Category 1 chemicals.
Appendix 3 – SCOMET List
3D002 [Reserved]
3D003 Combustors or pyrolysers capable of a heat-zone (‘burner’) temperature greater than 1,273 K (1000 Degree Centigrade), and in which any surfaces that come into direct contact with material coming into the containing chamber are made from, or lined with, any of the following materials:
a. Alloys with more than 25% nickel and 25% chromium by weight; (e.g., ‘Hatelloy’, ‘Illium’, ‘Inconel’, ‘Incoloy’)
b. Nickel, or alloys with more than 40% nickel by weight;
c. Titanium; or
d. Ceramics.
3D004 Toxic gas monitoring systems and their dedicated detecting components as follows: detectors; sensor devices; replaceable sensor cartridges; and dedicated software therefor
a. designed for continuous operation and usable for the detection of chemical warfare agents or Category 1 chemicals at concentrations of less than 0.3 mg/m³; or
b. designed for the detection of cholinesterase-inhibiting activity.
3D005 Containment facilities and related equipment as follows:
(1) Complete containment facilities that meet the criteria for P3 or P4 (BL3, BL4, L3, L4) containment as specified in the WHO Laboratory Biosafety Manual (3rd edition, Geneva, 2004)
(2) Equipment designed for fixed installation in containment facilities specified in 3D005a., as follows:
(i) Double-door pass-through decontamination autoclaves;
(ii) Breathing air suit decontamination showers;
(iii) Mechanical-seal or inflatable-seal walkthrough doors.
3D006 Fermenters:
(1) Fermenters capable of cultivation of micro-organisms or of live cells for the production of viruses or toxins, without the propagation of aerosols, having a capacity of 20 litres or greater.
(2) Components designed for such fermenters, as follows:
a. cultivation chambers designed to be sterilized or disinfected in situ;
b. cultivation chamber holding devices; or
c. process control units capable of simultaneously monitoring and controlling two or more fermentation system parameters (e.g. temperature, pH, nutrients, agitation, dissolved oxygen, air flow, foam control).
Technical Note: Fermenters include bioreactors (including single-use (disposable) bioreactors), chemostats and continuous-flow systems.
3D007 Centrifugal separators capable of the continuous separation of pathogenic micro-organisms, without the propagation of aerosols, and having all the following characteristics:
a. one or more sealing joints within the steam containment area;
b. a flow rate greater than 100 litres per hour;
c. components of polished stainless steel or titanium;
d. capable of in-situ steam sterilisation in a closed state.
Technical note: Centrifugal separators include decanters.
3D008 Cross (tangential) flow filtration equipment
(1) Cross (tangential) flow filtration equipment capable of separation of microorganisms, viruses, toxins or cell cultures having all the following characteristics:
a. a total filtration area equal to or greater than 1 square metre; and
b. having any of the following characteristics:
i. capable of being sterilized or disinfected in-situ; or
ii. using disposable or single-use filtration components.
Note: This control excludes reverse osmosis and hemodialysis equipment.
Appendix 3 – SCOMET List
(2) Cross (tangential) flow filtration components (e.g. modules, elements, cassettes, cartridges, units or plates) with filtration area equal to or greater than 0.2 square metres for each component and designed for use in cross (tangential) flow filtration equipment as specified above.
Technical note: In this control, 'sterilized' denotes the elimination of all viable microbes from the equipment through the use of either physical (e.g. steam) or chemical agents. 'Disinfected' denotes the destruction of potential microbial infectivity in the equipment through the use of chemical agents with a germicidal effect. 'Disinfection' and 'sterilization' are distinct from 'sanitization', the latter referring to cleaning procedures designed to lower the microbial content of equipment without necessarily achieving elimination of all microbial infectivity or viability.
3D009 Steam, gas or vapour sterilisable freeze-drying equipment with a condenser capacity of 10 kg of ice or greater in 24 hours and less than 1000 kg of ice in 24 hours.
3D010 Spray drying equipment capable of drying toxins or pathogenic microorganisms having all of the following characteristics:
a. A water evaporation capacity of ≥ 0.4 kg/h and ≤ 400 kg/h;
b. The ability to generate a typical mean product particle size of ≤10 micrometers with existing fittings or by minimal modification of the spray-dryer with atomization nozzles enabling generation of the required particle size; and
c. Capable of being sterilized or disinfected in situ.
3D011 Protective and containment equipment as follows:
a. Protective full or half suits, or hoods dependent upon a tethered external air supply and operating under positive pressure;
Technical note: This does not control suits designed to be worn with self-contained breathing apparatus.
b. Biocontainment chambers, isolators, or biological safety cabinets having all of the following characteristics, for normal operation:
i. fully enclosed workspace where the operator is separated from the work by a physical barrier;
ii. able to operate at negative pressure;
iii. means to safely manipulate items in the workspace;
iv. supply and exhaust air to and from the workspace is HEPA filtered.
Note 1 - this control includes class III biosafety cabinets, as described in the latest edition of the WHO Laboratory Biosafety Manual or constructed in accordance with national standards, regulations or guidance.
Note 2 - this control does not include isolators specially designed for barrier nursing or transportation of infected patients.
3D012 Aerosol inhalation equipment designed for aerosol challenge testing with micro-organisms, viruses or toxins as follows:
a. Whole-body exposure chambers having a capacity of 1 cubic metre or greater.
b. Nose-only exposure apparatus utilising directed aerosol flow and having capacity for exposure of 12 or more rodents, or 2 or more animals other than rodents; and, closed animal restraint tubes designed for use with such apparatus.
3D013 Spraying or fogging systems and components therefor, as follows:
a. Complete spraying or fogging systems, specially designed or modified for fitting to aircraft, lighter than air vehicles or UAVs, capable of delivering, from a liquid suspension, an initial droplet “VMD” of less than 50 microns at a flow rate of greater than two litres per minute.
b. Spray booms or arrays of aerosol generating units, specially designed or modified for fitting to aircraft, lighter than air vehicles or UAVs, capable of delivering, from a liquid suspension, an Appendix 3 – SCOMET List
initial droplet “VMD” of less than 50 microns at a flow rate of greater than two litres per minute.
c. Aerosol generating units specially designed for fitting to systems that fulfil all the criteria specified in 3D011.a and 3D001.b
Technical Notes
(1) Aerosol generating units are devices specially designed or modified for fitting to aircraft such as nozzles, rotary drum atomisers and similar devices.
(2) This entry does not control spraying or fogging systems and components as specified in 3D010 that are demonstrated not to be capable of delivering biological agents in the form of infectious aerosols.
(3) Droplet size for spray equipment or nozzles specially designed for use on aircraft or UAVs should be measured using either of the following methods:
(a) Doppler laser method
(b) Forward laser diffraction method
3D014 [Reserved]
3D015 Technology related to the development, production or use of items in 3D.
Appendix 3 – SCOMET List
Category 4 Nuclear-related other equipment, assemblies and components; test and production equipment; and related technology not controlled under Category 0 4A Equipment, assemblies, components including test and production equipment 4A001 Flow-forming machines, spin-forming machines capable of flow-forming functions, and mandrels, as follows:
a. For flow forming machines refer to 5A205
b. Spin forming machines having both of the following characteristics:
1. Three or more rollers (active or guiding); and
2. Which, according to the manufacturer’s technical specification, can be equipped with ‘numerical control’ units or a computer control.
c. Rotor-forming mandrels designed to form cylindrical rotors of inside diameter between 75 and 400 mm.
Note: Item 4A001a and 4A001b include machines which have only a single roller designed to deform metal plus two auxiliary rollers which support the mandrel, but do not participate directly in the deformation process.
4A002 Machine tools, as follows, and any combination thereof, for removing or cutting metals, ceramics, or composites, which, according to the manufacturer’s technical specifications, can be equipped with
electronic devices for simultaneous “contouring control” in two or more axes;
N.B.: For “numerical control” units controlled by their associated “software”, see Item 4C
a. Machine tools for turning, that have “positioning accuracies” with all compensations available better (less) than 6 µm according to ISO 230/2 (1988) along any linear axis (overall positioning) for machines capable of machining diameters greater than 35 mm;
Note: Item 4A002.a. does not control bar machines (Swissturn), limited to machining only bar feed thru, if maximum bar diameter is equal to or less than 42 mm and there is no capability of mounting chucks. Machines may have drilling and/or milling capabilities for machining parts with diameters less than 42 mm.
b. Machine tools for milling, having any of the following characteristics:
1. “Positioning accuracies” with all compensations available better (less) than 6 µm according to ISO 230/2 (1988) along any linear axis (overall positioning);
2. Two or more contouring rotary axes; or
3. Five or more axes which can be coordinated simultaneously for “contouring control”.
Note: Item 4A002.b. does not control milling machines having both of the following characteristics:
1. X-axis travel greater than 2 m; and
2. Overall “positioning accuracy” on the x-axis worse (more) than 30 µm according to ISO 230/2 (1988).
c. Machine tools for grinding, having any of the following characteristics:
1. “Positioning accuracies” with all compensations available better (less) than 4 µm
according to ISO 230/2 (1988) along any linear axis (overall positioning);
2. Two or more contouring rotary axes; or
3 Five or more axes which can be coordinated simultaneously for “contouring control”.
Note: Item 4A002.c. does not control grinding machines as follows:
1. Cylindrical external, internal, and external-internal grinding machines having all the following characteristics:
a. Limited to a maximum workpiece capacity of 150 mm outside diameter or length; and
b. Axes limited to x, z and c.
2. Jig grinders that do not have a z-axis or a w-axis with an overall positioning accuracy less (better) than 4 microns. Positioning accuracy is according to ISO 230/2 (1988).
Appendix 3 – SCOMET List
d. Non-wire type Electrical Discharge Machines (EDM) that have two or more contouring rotary axes and that can be coordinated simultaneously for “contouring control”.
Notes: 1. Stated “positioning accuracy” levels derived under the following procedures from measurements made according to ISO 230/2 (1988) or national equivalents may be used for each machine tool model if provided to, and accepted by, national authorities instead of individual machine tests.
Stated “positioning accuracy” are to be derived as follows:
a. Select five machines of a model to be evaluated;
b. Measure the linear axis accuracies according to ISO 230/2 (1988)
c. Determine the accuracy values (A) for each axis of each machine. The method of calculating the accuracy value is described in the ISO 230/2 (1988) standard;
d. Determine the average accuracy value of each axis. This average value becomes the stated “positioning accuracy” of each axis for the model (Âx, Ây...);
e. Since Item 4A002 refers to each linear axis, there will be as many stated “positioning accuracy” values as there are linear axes;
f. If any axis of a machine tool not controlled by Items 4A002.a., 4A002.b., or 4A002.c. has a stated “positioning accuracy” of 6 µm or better (less) for grinding machines, and 8 µm or better (less) for milling and turning machines, both according to ISO 230/2 (1988), then the builder should be required to reaffirm the accuracy level once every eighteen months.
2. Item 4A002. does not control special purpose machine tools limited to the manufacture of any of the following parts:
a. Gears
b. Crankshafts or cam shafts
c. Tools or cutters
d. Extruder worms
Technical Notes:
1. Axis nomenclature shall be in accordance with International Standard ISO 841, “Numerical Control Machines - Axis and Motion Nomenclature”.
2. Not counted in the total number of contouring axes are secondary parallel contouring axes (e.g., the w-axis on horizontal boring mills or a secondary rotary axis the centerline of which is parallel to the primary rotary axis).
3. Rotary axes do not necessarily have to rotate over 360 degrees. A rotary axis can be driven by a linear device, e.g., a screw or a rack-and-pinion.
4. For the purposes of 4A002. the number of axes which can be coordinated simultaneously for “contouring control” is the number of axes along or around which, during processing of the workpiece, simultaneous and interrelated motions are performed between the workpiece and a tool. This does not include any additional axes along or around which other relative motions within the machine are performed, such as:
a. Wheel-dressing systems in grinding machines;
b. Parallel rotary axes designed for mounting of separate workpieces;
c. Co-linear rotary axes designed for manipulating the same workpiece by holding it in a chuck from different ends.
5. A machine tool having at least 2 of the 3 turning, milling or grinding capabilities (e.g., a turning machine with milling capability) must be evaluated against each applicable entry, 4A002.a., 4A002.b. and 4A002.c.
Appendix 3 – SCOMET List
6. Items 4A002.b.3 and 4A002.c.3 include machines based on a parallel linear kinematic design (e.g., hexapods) that have 5 or more axes none of which are rotary axes.
4A003 Dimensional inspection machines, instruments, or systems, as follows:
a. Computer controlled or numerically controlled coordinate measuring machines (CMM) having either of the following characteristics:
1. Having only two axes and having a maximum permissible error of length measurement along any axis (one dimensional), identified as any combination of E0x MPE, E0y MPE or E0z MPE, equal to or less(better) than (1.25 + L/1000) μm (where L is the measured length in mm) at any point within the operating range of the machine (i.e., within the
length of the axis), according to ISO 10360-2(2009); or
2. Three or more axes and having a three dimensional (volumetric) maximum permissible error of length measurement (E0, MPE equal to or less (better) than (1.7 + L/800) µm (where L is the measured length in mm) at any point within the operating range of the machine (i.e., within the length of the axis), according to ISO 10360-2(2009).
Technical Note: The E0, MPE of the most accurate configuration of the CMM specified according to ISO 10360-2(2009) by the manufacturer (e.g., best of the following: probe stylus length, motion parameters, environment) and with all compensations available shall be compared to the 1.7 + L/ 800 µm threshold.
b. Linear displacement measuring instruments, as follows:
1. Non-contact type measuring systems with a “resolution” equal to or better (less) than 0.2 µm within a measuring range up to 0.2 mm;
2. Linear variable differential transformer (LVDT) systems having both of the following characteristics:
a. 1. “Linearity” equal to or less (better) than 0.1% measured from 0 to the full operating range, for LVDTs with an operating range up to 5 mm; or
2. “Linearity” equal to or less (better) than 0.1% measured from 0 to 5 mm for
LVDTs with an operating range greater than 5 mm; and
b. Drift equal to or better (less) than 0.1% per day at a standard ambient test room temperature ± 1 K;
3. Measuring systems having both of the following characteristics:
a. Contain a laser; and
b. Maintain for at least 12 hours, over a temperature range of ± 1 K around a
standard temperature and a standard pressure:
1. A “resolution” over their full scale of 0.1 µm or better; and
2. With a “measurement uncertainty” equal to or better (less) than (0.2 + L/2000) µm (L is the measured length in millimeters);
Note: Item 4A003.b.3 does not control measuring interferometer systems, without closed or open loop feedback, containing a laser to measure slide movement errors of machine tools, dimensional inspection
machines, or similar equipment
Technical Note: In Item 4A003.b.3 ‘linear displacement’ means the change of distance between the measuring probe and the measured object.
c. Angular displacement measuring instruments having an “angular position Appendix 3 – SCOMET List
deviation” equal to or better (less) than 0.00025°;
Note: Item 4A003.c does not control optical instruments, such as
autocollimators, using collimated light (e.g., laser light) to detect angular displacement of a mirror.
d. Systems for simultaneous linear-angular inspection of hemishells, having both of the following characteristics:
1. “Measurement uncertainty” along any linear axis equal to or better (less) than 3.5 µm per 5 mm; and
2. “Angular position deviation” equal to or less than 0.02°.
Notes:
1. “Item 4A003.d includes machine tools other than those specified by 4A002, that can be used as measuring machines if they meet or exceed the criteria specified for the measuring machine function.
2. Machines described in Item 4A003.d. are controlled if they exceed the threshold specified anywhere within their operating range”.
Technical Note: All parameters of measurement values in this item represent plus/minus, i.e., not total band.
| 4A004 | Controlled atmosphere (vacuum or inert gas) induction furnaces, and power supplies therefor, as follows: a. Furnaces having all of the following characteristics: 1. Capable of operation at temperatures above 1123 K (850 °C); 2. Induction coils 600 mm or less in diameter; and 3. Designed for power inputs of 5 kW or more; Note:Item 4A004.a. does not control furnaces designed for the processing of semiconductor wafers. b. Power supplies, with a specified output power of 5 kW or more, specially designed for furnaces specified in Item 4A004.a. |
4A005 Isostatic presses’, and related equipment, as follows:
a. ‘Isostatic presses’ as specified in 5A208;
b. Dies, moulds, and controls specially designed for the ‘isostatic presses’ specified in Item 4A005.a.
Technical Notes:
1. In Item 4A005 ´Isostatic presses’ means equipment capable of pressurizing a closed cavity through various media (gas, liquid, solid particles, etc.) to create equal pressure in all directions within the cavity upon a work piece or material.
2. In Item 4A005 the inside chamber dimension is that of the chamber in which both the working temperature and the working pressure are achieved and does not include fixtures. That dimension will be the smaller of either the inside diameter of the pressure chamber or the inside diameter of the insulated furnace chamber, depending on which of the two chambers is located inside the other.
4A006 Vibration test systems, equipment, and components as follows:
Appendix 3 – SCOMET List
a. Electrodynamic vibration test systems, having all of the following characteristics:
1. Employing feedback or closed loop control techniques and incorporating a digital control unit;
2. Capable of vibrating at 10 g RMS or more between 20 and 2000 Hz; and
3. Capable of imparting forces of 50 kN or greater measured ‘bare table’;
b. Digital control units, combined with ‘software’ specially designed for vibration testing, with a real-time bandwidth greater than 5 kHz and being designed for a system specified in Item 4A006.a.;
c. Vibration thrusters (shaker units), with or without associated amplifiers, capable of imparting a force of 50 kN or greater measured ‘bare table’, which are usable for the systems specified in Item 4A006.a.;
d. Test piece support structures and electronic units designed to combine multiple shaker units into a complete shaker system capable of providing an effective combined force of 50 kN or greater, measured ‘bare table,’ which are usable for the systems specified in Item 4A006.a..
Technical Note: In Item 4A006 ‘bare table’ means a flat table, or surface, with no fixtures or fittings.
4A007 Vacuum or other controlled atmosphere metallurgical melting and casting furnaces and related equipment, as follows:
a. Arc remelt furnacese, arc melt furnances and arc melt and casting furnaces having both of the following characteristics:
1. Consumable electrode capacities between 1000 and 20000 cm3; and
2. Capable of operating with melting temperatures above 1973 K (1700 °C);
b. Electron beam melting furnaces and plasma atomisation and melting furnaces, having both of the following characteristics:
1. A power of 50 kW or greater; and
2. Capable of operating with melting temperatures above 1473 K (1200 °C);
c. Computer control and monitoring systems specially configured for any of the furnaces specified in Item 4A007.a. or 4A007.b.
d. Plasma torches specially designed for the furnaces specified in 4A007.b.having both of the following characteristics:
1. Operating at a power greater than 50kW; and
2. Capable of operating above 1473 K (1200°C);
e. Electron beam guns specially designed for the furnaces specified in 4A007.b.operating at a power greater than 50kW”.
4A008 Crucibles made of materials resistant to liquid actinide metals, as follows:
a. Crucibles having both of the following characteristics:
1. A volume of between 150 cm3 (150 ml) and 8000 cm3 (8 litres); and
2. Made of or coated with any of the following materials, or combination of the following materials, having an overall impurity level of 2% or less by weight:
a. Calcium fluoride (CaF2);
b. Calcium zirconate (metazirconate) (CaZrO3);
c. Cerium sulphide (Ce2S3);
d. Erbium oxide (erbia) (Er2O3);
e. Hafnium oxide (hafnia) (HfO2);
f. Magnesium oxide (MgO);
Appendix 3 – SCOMET List
g. Nitrided niobium-titanium-tungsten alloy (approximately 50% Nb, 30% Ti, 20% W);
h. Yttrium oxide (yttria) (Y2O3); or
i. Zirconium oxide (zirconia) (ZrO2);
b. Crucibles having both of the following characteristics:
1. A volume of between 50 cm3 (50 ml) and 2000 cm3 (2 litres); and
2. Made of or lined with tantalum, having a purity of 99.9% or greater by weight;
c. Crucibles having all of the following characteristics:
1. A volume of between 50 cm3 (50 ml) and 2000 cm3 (2 litres);
2. Made of or lined with tantalum, having a purity of 98% or greater by weight; and
3. Coated with tantalum carbide, nitride, boride, or any combination thereof.
4A009 Platinized catalysts specially designed or prepared for promoting the hydrogen isotope exchange reaction between hydrogen and water for the recovery of tritium from heavy water or for the production of heavy water.
4A010 Composite structures in the form of tubes having both of the following characteristics:
a. An inside diameter of between 75 and 400 mm; and
b. Made with any of the materials specified in Item 3A116.
4A011 Frequency changers or generators, usable as a variable frequency or fixed frequency motor drive, having all of the following characteristics:
N.B.1: Frequency changers and generators specially designed or prepared for the gas centrifuge process are controlled under Prescribe Equipment (0B)
N.B.2: “Software” specially designed to enhance or release the performance of frequency changers or generators to meet the characteristics below is controlled (see Item 4C).
a. Multiphase output providing a power of 40 VA or greater;
b. Operating at a frequency of 600 Hz or more; and
c. Frequency control better (less) than 0.2%.
Notes: 1. Item 4A011 only controls frequency changers intended for specific industrial machinery and/or consumer goods (machine tools, vehicles, etc.) if the frequency changers can meet the characteristics above when removed,
2. For the purpose of export control, the Government will determine whether or not a particular frequency changer meets the characteristics above, taking into account hardware and software constraints.
Technical Notes: 1. Frequency changers in Item 4A011. are also known as converters or inverters.
2. The characteristics specified in item 4A011 may be met by certain equipment marketed such as: Generators, Electronic Test Equipment, AC Power Supplies, Variable Speed
Motor Drives, Variable Speed Drives (VSDs), Variable Frequency Drives (VFDs),
Adjustable Frequency Drives (AFDs), or Adjustable Speed Drives (ASDs).
4A012 Lasers, laser amplifiers and oscillators as follows:
a. Copper vapour lasers having both of the following characteristics:
Appendix 3 – SCOMET List
1. Operating at wavelengths between 500 and 600 nm; and
2. An average output power equal to or greater than 40 W;
b. Argon ion lasers having both of the following characteristics:
1. Operating at wavelengths between 400 and 515 nm; and
2. An average output power greater than 40 W;
c. Neodymium-doped (other than glass) lasers with an output wavelength between 1000 and 1100 nm having either of the following:
1. Pulse-excited and Q-switched with a pulse duration equal to or greater than 1 ns, and having either of the following:
a. A single-transverse mode output with an average output power greater than 40 W; or
b. A multiple-transverse mode output with an average output power greater than 50 W;
or
2. Incorporating frequency doubling to give an output wavelength between 500 and 550 nm with an average output power of greater than 40 W;
d. Tuneable pulsed single-mode dye laser oscillators having all of the following characteristics:
1. Operating at wavelengths between 300 and 800 nm;
2. An average output power greater than 1 W;
3. A repetition rate greater than 1 kHz; and
4. Pulse width less than 100 ns;
e. Tuneable pulsed dye laser amplifiers and oscillators having all of the following characteristics:
1. Operating at wavelengths between 300 and 800 nm;
2. An average output power greater than 30 W;
3. A repetition rate greater than 1 kHz; and
4. Pulse width less than 100 ns;
Note: Item 4A012e does not control single mode oscillators.
f. Alexandrite lasers having all of the following characteristics:
1. Operating at wavelengths between 720 and 800 nm;
2. A bandwidth of 0.005 nm or less;
3. A repetition rate greater than 125 Hz; and
4. An average output power greater than 30 W;
g. Pulsed carbon dioxide lasers having all of the following characteristics:
1. Operating at wavelengths between 9000 and 11000 nm;
2. A repetition rate greater than 250 Hz;
3. An average output power greater than 500 W; and
4. Pulse width of less than 200 ns;
Note: Item 4A012g does not control the higher power (typically 1 to 5 1kW) industrial CO2 lasers used in applications such as cutting and welding, as these latter lasers are either continuous wave or are pulsed with a pulse width greater than 200 ns.
Appendix 3 – SCOMET List
h. Pulsed excimer lasers (XeF, XeCl, KrF) having all of the following characteristics:
1. Operating at wavelengths between 240 and 360 nm;
2. A repetition rate greater than 250 Hz; and
3. An average output power greater than 500 W;
i. Para-hydrogen Raman shifters designed to operate at 16 µm output wavelength and at a repetition rate greater than 250 Hz.
j. Pulsed carbon monoxide lasers having all of the following characteristics:
1. Operating at wavelengths between 5000 and 6000 nm;
2. A repetition rate greater than 250 Hz;
3. An average output power greater than 200 W; and
4. Pulse width of less than 200 ns.
Note:Item 4A012.j. does not control the higher power (typically 1 to 5 kW) industrial CO lasers used in applications such as cutting and welding, as these latter lasers are either continuous wave or are pulsed with a pulse width greater than 200 ns.
4A013 Valves having all of the following characteristics:
a. A nominal size of 5 mm or greater;
b. Having a bellows seal; and
c. Wholly made of or lined with aluminium, aluminium alloy, nickel, or nickel alloy containing more than 60% nickel by weight.
Technical Note: For valves with different inlet and outlet diameter, the nominal size parameter in Item 4A013a refers to the smallest diameter.
4A014 Superconducting solenoidal electromagnets having all of the following characteristics:
a. Capable of creating magnetic fields greater than 2 T;
b. A ratio of length to inner diameter greater than 2;
c. Inner diameter greater than 300 mm; and
d. Magnetic field uniform to better than 1% over the central 50% of the inner volume.
Note: Item 4A014 does not control magnets specially designed for and exported as part of medical nuclear magnetic resonance (NMR) imaging systems. (‘As part of’ does not necessarily mean physical part in the same shipment. Separate shipments from different sources are allowed, provided the related export documents clearly specify the ‘as part of” relationship.)
4A015 High-power direct current power supplies having both of the following characteristics:
a. Capable of continuously producing, over a time period of 8 hours, 100 V or greater with current output of 500 A or greater; and
b. Current or voltage stability better than 0.1% over a time period of 8 hours 4A016 High-voltage direct current power supplies having both of the following characteristics:
a. Capable of continuously producing, over a time period of 8 hours, 20 kV or greater with current output of 1 A or greater; and
b. Current or voltage stability better than 0.1% over a time period of 8 hours.
4A017 All types of pressure transducers capable of measuring absolute pressures and having all of the following characteristics:
a. Pressure sensing elements made of or protected by aluminium, aluminium alloy, aluminium oxide (alumina or sapphire), nickel, nickel alloy with more than 60% nickel by Appendix 3 – SCOMET List
weight, or fully fluorinated hydrocarbon polymers;
b. Seals, if any, essential for sealing the pressure sensing element, and in direct contact with the process medium, made of or protected by aluminium, aluminium alloy, aluminium oxide (alumina or sapphire), nickel, nickel alloy with more than 60% nickel by weight, or fully fluorinated hydrocarbon polymers; and
c. Having either of the following characteristics:
1. A full scale of less than 13 kPa and an “accuracy” of better than 1% of full scale; or
2. A full scale of 13 kPa or greater and an “accuracy” of better than 130 Pa when measuring at 13 kPa”.
Technical Notes:
1. In Item 4A017. pressure transducers are devices that convert pressure measurements into a signal.
2. In Item 4A017. “accuracy” includes non-linearity, hysteresis and repeatability at ambient temperature.
4A018 Vacuum pumps having all of the following characteristics:
a. Input throat size equal to or greater than 380 mm;
b. Pumping speed equal to or greater than 15 m3/s; and
c. Capable of producing an ultimate vacuum better than 13.3 mPa.
Technical Notes:
1. The pumping speed is determined at the measurement point with nitrogen gas or air.
2. The ultimate vacuum is determined at the input of the pump with the input of the pump blocked off.
4A019 Electrolytic cells for fluorine production with an output capacity greater than 250 g of fluorine per hour.
4A020 Rotor fabrication or assembly equipment, rotor straightening equipment, bellows-forming mandrels and dies, as follows:
a. Rotor assembly equipment for assembly of gas centrifuge rotor tube sections, baffles, and end caps; Note: Item 4A020a includes precision mandrels, clamps, and shrink fit machines.
b. Rotor straightening equipment for alignment of gas centrifuge rotor tube sections to a common axis;
Technical Note: In Item 4A020b such equipment normally consists of precision measuring probes linked to a computer that subsequently controls the action of, for example, pneumatic rams used for aligning the rotor tube sections.
c. Bellows-forming mandrels and dies for producing single -convolution bellows.
Technical Note: The bellows referred to in Item 4A020c have all of the following characteristics:
1. Inside diameter between 75 and 400 mm;
2. Length equal to or greater than 12.7 mm;
3. Single convolution depth greater than 2 mm; and
4. Made of high-strength aluminium alloys, maraging steel, or high strength fibrous or filamentary materials.
Appendix 3 – SCOMET List
4A021 Centrifugal multi-plane balancing machines, fixed or portable, horizontal or vertical, as follows:
a. Centrifugal balancing machines designed for balancing flexible rotors having a length of 600 mm or more and having all of the following characteristics:
1. Swing or journal diameter greater than 75 mm;
2. Mass capability of from 0.9 to 23 kg; and
3. Capable of balancing speed of revolution greater than 5000 rpm;
b. Centrifugal balancing machines designed for balancing hollow cylindrical rotor components and having all of the following characteristics:
1. Journal diameter greater than 75 mm;
2. Mass capability of from 0.9 to 23 kg;
3. A minimum achievable residual specific unbalance equal to or less than 10 gmm/kg per plane; and
4. Belt drive type.
4A022 Filament winding machines and related equipment, as follows:
a. Filament winding machines as specified in 5A206; and having all of the following characteristics:
1. Having motions for positioning, wrapping, and winding fibers coordinated and programmed in two or more axes;
2. Specially designed to fabricate composite structures or laminates from “fibrous or filamentary materials”; and
3. Capable of winding cylindrical tubes with an internal diameter between 75 and 650 mm and lengths of 300 mm or greater;
b. Coordinating and programming controls for the filament winding machines specified in Item 4A022a;
c. Precision mandrels for the filament winding machines specified in Item 4A022a.
4A023 Electromagnetic isotope separators designed for, or equipped with, single or multiple ion sources capable of providing a total ion beam current of 50 mA or greater.
Notes:
1. Item 4A023 includes separators capable of enriching stable isotopes as well as those for uranium. (A separator capable of separating the isotopes of lead with a one-mass unit difference is inherently capable of enriching the isotopes of uranium with a three-unit mass difference.)
2. Item 4A023 includes separators with the ion sources and collectors both in the magnetic field and those configurations in which they are external to the field.
Technical Note: A single 50 mA ion source cannot produce more than 3 g of separated highly enriched uranium (HEU) per year from natural abundance feed.
4A024 Mass spectrometers capable of measuring ions of 230 atomic mass units or greater and having a resolution of better than 2 parts in 230, as follows, and ion sources therefor:
N.B.: Mass spectrometers specially designed or prepared for analyzing on-line samples of uranium hexafluoride are controlled under Prescribed Equipment (0B Category).
Appendix 3 – SCOMET List
a. Inductively coupled plasma mass spectrometers (ICP/MS);
b. Glow discharge mass spectrometers (GDMS);
c. Thermal ionization mass spectrometers (TIMS);
d. Electron bombardment mass spectrometers having both of the following features:
1. A molecular beam inlet system that injects a collimated beam of analyte
molecules into a region of the ion source where the molecules are ionized by an electron beam; and
2. One or more cold traps that can be cooled to a temperature of 193 K (-80 °C) or less in order to trap analyte molecules that are not ionized by the electron beam;
e. Mass spectrometers equipped with a microfluorination ion source designed for actinides or actinide fluorides.
Technical Notes:
1. Item 4A024.d. describes mass spectrometers that are typically used for isotopic analysis of UF6 gas samples.
2. Electron bombardment mass spectrometers in Item 4A024.d. are also known as electron impact mass spectrometers or electron ionization mass spectrometers.
3. In Item 4A024.d.2, a ‘cold trap’ is a device that traps gas molecules by condensing or freezing them on cold surfaces. For the purposes of this entry, a closed-loop gaseous helium cryogenic vacuum pump is not a cold trap.
4A025 Specialized packings which may be used in separating heavy water from ordinary water, having both of the following characteristics:
a.Made of phosphor bronze mesh chemically treated to improve wettability; and
b. Designed to be used in vacuum distillation towers.
4A026 Pumps capable of circulating solutions of concentrated or dilute potassium amide catalyst in liquid ammonia (KNH2/NH3), having all of the following characteristics:
. a. Airtight (i.e., hermetically sealed);
b. A capacity greater than 8.5 m3/h; and
c. Either of the following characteristics:
1. For concentrated potassium amide solutions (1% or greater), an operating pressure of 1.5 to 60 MPa; or
2. For dilute potassium amide solutions (less than 1%), an operating pressure of 20 to 60 MPa.
4A027 Turboexpanders or turboexpander-compressor sets having both of the following characteristics:
a. Designed for operation with an outlet temperature of 35 K (- 238 ºC) or less; and
b. Designed for a throughput of hydrogen gas of 1000 kg/h or greater.
4A028 Water-hydrogen sulphide exchange tray columns and internal contactors, as follows:
N.B.: For columns which are specially designed or prepared for the production of heavy Appendix 3 – SCOMET List
water, see Prescribed Equipment (0B002).
a. Water-hydrogen sulphide exchange tray columns, having all of the following
characteristics:
1. Can operate at pressures of 2 MPa or greater;
2. Constructed of carbon steel having an austenitic ASTM (or equivalent standard) grain size number of 5 or greater; and
3. With a diameter of 1.8 m or greater;
b. Internal contactors for the water-hydrogen sulphide exchange tray columns specified in Item 4A028a.
Technical Note: Internal contactors of the columns are segmented trays which have an effective assembled diameter of 1.8 m or greater; are designed to facilitate counter current contacting and are constructed of stainless steels with a carbon content of 0.03% or less.
These may be sieve trays, valve trays, bubble cap trays or turbo grid trays.
4A029 Hydrogen-cryogenic distillation columns having all of the following characteristics:
a. Designed for operation at internal temperatures of 35 K (-238 ºC) or less;
b. Designed for operation at internal pressures of 0.5 to 5 MPa;
c. Constructed of either:
1. Stainless steel of the 300 series with low sulfur content and with an austenitic ASTM (or equivalent standard) grain size number of 5 or greater; or
2. Equivalent materials which are both cryogenic and H2-compatible; and
d. With internal diameters of 30 cm or greater and ‘effective lengths’ of 4 m or greater.
Technical Note: The term ‘effective length’ means the active height of packing material in a packed-type column, or the active height of internal contactor plates in a plate-type column.
4A030 Bellows-sealed scroll-type compressors and bellows-sealed scroll-type vacuum pumps having all of the following characteristics:
a. Capable of an inlet volume flow rate of 50 m3/h or greater;
b. Capable of a pressure ratio of 2:1 or greater; and
c. Having all surfaces that come in contact with the process gas made from any of the following materials:
1. Aluminium or aluminium alloy;
2. Aluminium oxide;
3. Stainless steel;
4. Nickel or nickel alloy;
5. Phosphor bronze; or
6. Fluoropolymers.
Technical Notes:
1. In a scroll compressor or vacuum pump, crescent-shaped pockets of gas are trapped between one or more pairs of intermeshed spiral vanes, or scrolls, one of which moves while the other remains stationary. The moving scroll orbits the stationary scroll; it does not rotate. As the moving scroll orbits the stationary scroll, the gas pockets diminish in size (i.e., Appendix 3 – SCOMET List
they are compressed) as they move toward the outlet port of the machine.
2. In a bellows-sealed scroll compressor or vacuum pump, the process gas is totally isolated from the lubricated parts of the pump and from the external atmosphere by a metal bellows. One end of the bellows is attached to the moving scroll and the other end is attached to the stationary housing of the pump.
3. Fluoropolymers include, but are not limited to, the following materials:
a. Polytetrafluoroethylene (PTFE),
b. Fluorinated Ethylene Propylene (FEP),
c. Perfluoroalkoxy (PFA),
d. Polychlorotrifluoroethylene (PCTFE); and
e. Vinylidene fluoride-hexafluoropropylene copolymer.
4A031 Industrial equipment including assemblies and components (other than those specified under Prescribed Equipment in 0B003.e) as follows:
a. High-density (lead glass or other) radiation shielding windows, having all of the following characteristics, and specially designed frames therefor:
1. A ‘cold area’ greater than 0.09 m2;
2. A density greater than 3 g/cm3; and
3. A thickness of 100 mm or greater.
Technical Note: In Item 4A031.a.1. the term ‘cold area’ means the viewing area of the window exposed to the lowest level of radiation in the design application.
b. Radiation-hardened TV cameras, or lenses therefor, specially designed or rated as radiation hardened to withstand a total radiation dose greater than 5 x 104 Gy (silicon) without operational degradation.
Technical Note: The term Gy (silicon) refers to the energy in Joules per kilogram absorbed by an unshielded silicon sample when exposed to ionizing radiation.
c. ‘Robots’, ‘end-effectors’ and control units as follows:
1. ‘Robots’ or ‘end-effectors’ having either of the following characteristics:
(a) Specially designed to comply with national safety standards applicable to handling high explosives (for example, meeting electrical code ratings for high explosives); or
(b) Specially designed or rated as radiation hardened to withstand a total radiation dose greater than 5 x 104 Gy (silicon) without operational degradation;
2. Control units specially designed for any of the ‘robots’ or ‘end-effectors’ specified in Item 4A031.c.1.
Note:Item 1.A.3. does not control ‘robots’ specially designed for non-nuclear industrial applications such as automobile paint-spraying booths.
Technical Notes:
1. ‘Robots’In Item 4A031.c. ‘robot’ means a manipulation mechanism, which may be of the continuous path or of the point-to-point variety, may use “sensors”, and has all of the following characteristics:
Appendix 3 – SCOMET List
(a) is multifunctional;
(b) is capable of positioning or orienting material, parts, tools, or special devices through variable movements in three-dimensional space;
(c) incorporates three or more closed or open loop servo-devices which may
include stepping motors; and
(d) has “user-accessible programmability” by means of teach/playback method or
by means of an electronic computer which may be a programmable logic
controller, i.e., without mechanical intervention.
N.B.1:
In the above definition “sensors” means detectors of a physical phenomenon, the output of which (after conversion into a signal that can be interpreted by a control unit) is able to generate “programs” or modify programmed instructions or numerical “program” data. This includes “sensors” with machine vision, infrared imaging, acoustical imaging, tactile feel, inertial position measuring, optical or acoustic ranging or force or torque measuring capabilities.
N.B.2:
In the above definition “user-accessible programmability” means the facility allowing a user to insert, modify or replace “programs” by means other than:
(a) a physical change in wiring or interconnections; or
(b) the setting of function controls including entry of parameters.
N.B.3:
The above definition does not include the following devices:
(a) Manipulation mechanisms which are only manually/teleoperator controllable;
(b) Fixed sequence manipulation mechanisms which are automated moving devices operating according to mechanically fixed programmed motions. The “program” is mechanically limited by fixed stops, such as pins or cams. The sequence of motions and the selection of paths or angles are not variable or changeable by mechanical, electronic, or electrical means;
(c) Mechanically controlled variable sequence manipulation mechanisms which are automated moving devices operating according to mechanically fixed programmed motions. The “program” is mechanically limited by fixed, but adjustable, stops such as pins or cams. The sequence of motions and the selection of paths or angles are variable within the fixed “program” pattern. Variations or modifications of the “program” pattern (e.g., changes of pins or exchanges of cams) in one or more motion axes are accomplished only through mechanical operations;
(d) Non-servo-controlled variable sequence manipulation mechanisms which are automated moving devices, operating according to mechanically fixed programmed motions. The “program” is variable but the sequence proceeds only by the binary signal from mechanically fixed electrical binary devices or adjustable stops;
(e) Stacker cranes defined as Cartesian coordinate manipulator systems manufactured as an integral part of a vertical array of storage bins and designed to access the contents of those bins for storage or retrieval.
2. ‘End-effectors’
Appendix 3 – SCOMET List
In Item 4A031.c. ‘end-effectors’ are grippers, ‘active tooling units’, and any other tooling that is attached to the baseplate on the end of a ‘robot’ manipulator arm.
N.B.:
In the above definition ‘active tooling units’ is a device for applying motive power, process energy or sensing to the workpiece.
d. Remote manipulators that can be used to provide remote actions in radiochemical separation
operations or hot cells, having either of the following characteristics:
1. A capability of penetrating 0.6 m or more of hot cell wall (through-the-wall operation); or
2. A capability of bridging over the top of a hot cell wall with a thickness of 0.6 m or more (over-the-wall operation).
Technical Note: Remote manipulators provide translation of human operator actions to a remote operating arm and terminal fixture. They may be of a master/slave type or operated by joystick or keypad.
4B Equipment, assemblies and components, including test and measurement equipment usable in development of nuclear explosive devices
4B001 Photomultiplier tubes having both of the following characteristics:
a. Photocathode area of greater than 20 cm2; and
b. Anode pulse rise time of less than 1 ns.
4B002 Flash X-ray generators or pulsed electron accelerators having either of the following sets of characteristics:
a. 1. An accelerator peak electron energy of 500 keV or greater but less than 25 MeV; and
2. With a figure of merit (K) of 0.25 or greater; or
b. 1. An accelerator peak electron energy of 25 MeV or greater; and
2. A peak power greater than 50 MW.
Note: Item 4B002 does not control accelerators that are component parts of devices designed for purposes other than electron beam or X-ray radiation (electron microscopy, for example) nor those designed for medical purposes.
Technical Notes:
1. The figure of merit K is defined as: K=1.7 x 103 V2.65Q. V is the peak electron energy in million electron volts. If the accelerator beam pulse duration is less than or equal to 1µs, then Q is the total accelerated charge in Coulombs. If the accelerator beam pulse duration is greater than 1 µs, then Q is the maximum accelerated charge in 1 µs. Q equals the integral of i with respect to t, over the lesser of 1 µs or the time duration of the beam pulse ( Q= ∫idt ) where i is beam current in amperes and t is the time in seconds.
2. Peak power = (peak potential in volts) x (peak beam current in amperes).
3. In machines based on microwave accelerating cavities, the time duration of the beam pulse is the lesser of 1 µs or the duration of the bunched beam packet resulting from one microwave modulator pulse.
4. In machines based on microwave accelerating cavities, the peak beam current is the average current in the time duration of a bunched beam packet.
Appendix 3 – SCOMET List
| 4B003 | High-velocity gun systems (propellant, gas, coil, electromagnetic, and electrothermal types, other advanced systems) capable of accelerating projectiles to 1.5 km/s or greater. Note: This item does not control guns specially designed for high velocity weapon systems. | and |
4B004 High-speed cameras and imaging devices and components therefor, as follows:
N.B.: “Software” specially designed to enhance or release the performance of cameras or imaging devices to meet the characteristics below is controlled (See Item 4C).
a. Streak cameras, and specially designed components therefor, as follows:
1. Streak cameras with writing speeds greater than 0.5 mm/μs;
2. Electronic streak cameras capable of 50 ns or less time resolution;
3. Streak tubes for cameras specified in 4B004.a.2.;
4. Plug-ins specially designed for use with streak cameras which have modular structures
and that enable the performance specifications in 4B004.a.1 or 4B004.a.2.;
5. Synchronizing electronics units, rotor assemblies consisting of turbines, mirrors and
bearings specially designed for cameras specified in 4B004.a.1.
b. Framing cameras and specially designed components therefor as follows:
1. Framing cameras with recording rates greater than 225,000 frames per second;
2. Framing cameras capable of 50 ns or less frame exposure time;
3. Framing tubes and solid-state imaging devices having a fast image gating (shutter) time of 50ns or less specially designed for cameras specified in 4B004.b.1 or 4B004.b.2.;
4. Plug-ins specially designed for use with framing cameras which have modular structures
and that enable the performance specifications in 4B004.b.1 or 4B004.b.2.;
5. Synchronizing electronics units, rotor assemblies consisting of turbines, mirrors and
bearings specially designed for cameras specified in 4B004.b.1 or 4B004.b.2.
c. Solid state or electron tube cameras and specially designed components therefor as follows:
1. Solid-state cameras or electron tube cameras with a fast image gating (shutter) time of 50 ns or less;
2. Solid-state imaging devices and image intensifiers tubes having a fast image gating (shutter) time of 50 ns or less specially designed for cameras specified in 4B004.c.1.;
3. Electro-optical shuttering devices (Kerr or Pockels cells) with a fast image gating (shutter) time of 50 ns or less;
4. Plug-ins specially designed for use with cameras which have modular structures and that enable the performance specifications in 4B004.c.1.
Technical Note: High speed single frame cameras can be used alone to produce a single image of a dynamic event, or several such cameras can be combined in a sequentially-triggered system to produce multiple images of an event.
4B005 High explosive containment vessels, chambers, containers and other similar containment devices designed for the testing of high explosives or explosive devices and having both of the following Appendix 3 – SCOMET List
characteristics:
a. Designed to fully contain an explosion equivalent to 2 kg of TNT or greater; and
b. Having design elements or features enabling real time or delayed transfer of diagnostic or measurement information.
4B006 Specialized instrumentation for hydrodynamic experiments, as follows:
a. Velocity interferometers for measuring velocities exceeding 1 km/s during time intervals of less than 10 μs;
b. Shock pressure gauges capable of measuring pressures greater than 10GPa, including gauges made with manganin, ytterbium, and polyvinylidene fluoride (PVDF) / polyvinyl difluoride(PVF2).
c. Quartz pressure transducers for pressures greater than 10 GPa.
Note: Item 4B006.a. includes velocity interferometers such as VISARs (Velocity Interferometer Systems for Any Reflector), DLIs (Doppler Laser Interferometers) and
PDV (Photonic Doppler Velocimeters) also known as Het-V (Heterodyne
Velocimeters).
4B007 High-speed pulse generators, and pulse heads therefor, having both of the following characteristics:
a. Output voltage greater than 6 V into a resistive load of less than 55 ohms; and
b. ‘Pulse transition time’ less than 500 ps.
Technical Notes:
1. In Item 4B007.b. ‘pulse transition time’ is defined as the time interval between 10% and 90% voltage amplitude.
2. Pulse heads are impulse forming networks designed to accept a voltage step function and shape it into a variety of pulse forms that can include rectangular, triangular, step, impulse, exponential, or monocycle types. Pulse heads can be an integral part of the pulse generator, they can be a plug-in module to the device or they can be an externally connected device.
4B008 Detonators and multipoint initiation systems, as follows:
a. Electrically driven explosive detonators, as follows:
1. Exploding bridge (EB);
2. Exploding bridge wire (EBW);
3. Slapper;
4. Exploding foil initiators (EFI);
b. Arrangements using single or multiple detonators designed to nearly simultaneously initiate an explosive surface over an area greater than 5000 mm2 from a single firing signal with an initiation timing spread over the surface of less than 2.5 µs.
Note: Item 4B008. does not control detonators using only primary explosives, such as lead azide.
Technical Note:
In Item 4B008. the detonators of concern all utilize a small electrical conductor (bridge, bridge wire, or foil) that explosively vaporizes when a fast, high-current electrical pulse is passed through it. In nonslapper types,the exploding conductor starts a chemical detonation in a contacting high-explosive material such as PETN (pentaerythritoltetranitrate). In slapper detonators, the explosive vaporization of the electrical conductor drives a flyer or slapper across a gap, and the impact of the slapper on an explosive starts a chemical detonation. The slapper in some designs is driven by magnetic force. The term exploding foil detonator may refer to either an EB or a slapper-type detonator. Also, the word initiator is sometimes used in place of the word detonator.
Appendix 3 – SCOMET List
4B009 Firing sets and equivalent high-current pulse generators, as follows:
a. Detonator firing sets (initiation systems, firesets), including electronically-charged, explosivelydriven and optically-driven firing sets designed to drive multiple controlled detonators specified by Item 4B008 above;
b. Modular electrical pulse generators (pulsers) having all of the following characteristics:
1. Designed for portable, mobile, or ruggedized-use;
2. Capable of delivering their energy in less than 15 µs into loads of less than 40 ohms;
3. Having an output greater than 100 A;
4. No dimension greater than 30 cm;
5. Weight less than 30 kg ; and
6. Specified to operate over an extended temperature range of 223 to 373 K (-50 ºC to
100 ºC) or specified as suitable for aerospace applications.
c. Micro-firing units having all of the following characteristics:
1. No dimension greater than 35 mm;
2. Voltage rating of equal to or greater than 1 kV; and
3. Capacitance of equal to or greater than 100 nF.
Note: Optically driven firing sets include both those employing laser initiation and laser charging. Explosively-driven firing sets include both explosive ferroelectric and explosive ferromagnetic firing set types. Item 4B009.b. includes xenon flashlamp drivers.
4B010 Switching devices as follows:
a. Cold-cathode tubes, whether gas filled or not, operating similarly to a spark gap, having all of the following characteristics:
1. Containing three or more electrodes;
2. Anode peak voltage rating of 2.5 kV or more;
3. Anode peak current rating of 100 A or more; and
4. Anode delay time of 10 µs or less;
Note: Item 4B010.a. includes gas krytron tubes and vacuum sprytron tubes.
b. Triggered spark-gaps having both of the following characteristics:
1. Anode delay time of 15 µs or less; and
2. Rated for a peak current of 500 A or more;
c. Modules or assemblies with a fast switching function having all of the following characteristics:
1. Anode peak voltage rating greater than 2 kV;
Appendix 3 – SCOMET List
2. Anode peak current rating of 500 A or more; and
3. Turn-on time of 1 µs or less.
4B011 Pulse discharge capacitors having either of the following sets of characteristics:
a. 1. Voltage rating greater than 1.4 kV;
2. Energy storage greater than 10 J;
3. Capacitance greater than 0.5 µF; and
4. Series inductance less than 50 nH; or
b. 1. Voltage rating greater than 750 V;
2. Capacitance greater than 0.25 µF; and
3. Series inductance less than 10 nH.
4B012 Neutron generator systems, including tubes, having both of the following characteristics:
a. Designed for operation without an external vacuum system; and
b. 1. Utilizing electrostatic acceleration to induce a tritium-deuterium nuclear reaction; or
2. Utilizing electrostatic acceleration to induce a deuterium-deuterium nuclear reaction
and capable of an Output of 3 x 109 neutrons/s or greater.
4B013 Striplines to provide low inductance path to detonators with the following characteristics:
a. Voltage rating greater than 2 kV; and
b. Inductance of less than 20 nH
4C Technology and Software
Technology and software for the development, production or use of items specified in 4A or 4B.
Appendix 3 – SCOMET List
5 Aerospace systems, equipment including production and test equipment,
related technology, and specially designed components and accessories
therefor.
5A Rocket Systems (including ballistic missiles, space launch vehicles and sounding rockets)
5A1 Systems
5A101 Systems for missiles and rockets, including:
a. complete rocket systems (including ballistic missile systems, space launch vehicles and sounding rockets)
b. complete rocket stages with engines
c. solid or liquid fuel rocket engines and their control systems including liquid propellant
apogee engines designed or modified for satellites
Note: 5A101 does not control JATO units, propulsion units for flares, ejection seats, emergency
escape equipment and rockets for display fireworks.
5A102 Subsystems and components usable in missiles and rockets including:
a. rocket motor cases, interior lining, insulation and nozzles;
b. rocket staging mechanisms, separation mechanisms and inter-stages;
c. Liquid, slurry and gel propellant (including oxidisers) control systems, and specially designed components therefor, usable in missiles and rockets, designed or modified to operate in vibration
environments greater than 10 g rms between 20 Hz and 2 kHz.
Notes:
1. The only servo valves, pumps and gas turbines specified in 3.A.5. are the following:
• Servo valves designed for flow rates equal to or greater than 24 litres per minute, at an absolute pressure equal to or greater than 7 MPa, that have an actuator
response time of less than 100 ms.
• Pumps, for liquid propellants, with shaft speeds equal to or greater than 8,000 rpm at the maximum operating mode or with discharge pressures equal to or greater than 7 MPa
• Gas turbines, for liquid propellant turbopumps, with shaft speeds equal to or greater than 8,000 rpm at the maximum operating mode.
2. Systems and components specified in this clause may be exported as part of a satellite”;
d. re-entry vehicles and equipment including
1. Heat-shields and components thereof, fabricated of ceramic or ablative materials;
2. Heat sinks and components thereof, fabricated of light weight, high heat capacity materials;
3. Electronic equipment specially designed for re-entry vehicles.
e. guidance systems and their components such as gyros and inertial reference units;
f. thrust-vector control subsystems including methods of achieving thrust vector control such as flexible nozzle, fluid or secondary gas injection, movable engine or nozzle, deflection of exhaust gas stream (jet vanes or probes) and use of thrust tabs;
g. hybrid rocket motors and components thereof;
h. safing, arming, fusing and firing mechanisms for weapons or warhead.
i. software specially designed for reduced observables such as radar reflectivity, ultraviolet/infrared signatures and acoustic signatures.
j. Combustion chambers and nozzles for liquid propellant rocket engines or gel propellant rocket motors
5A2 Production and Test Equipment.
5A201 Transonic, supersonic, hypersonic wind tunnels; shock tunnels; gun tunnels; aeroballistic ranges.
Appendix 3 – SCOMET List
5A202 Test and production equipment and facilities designed to handle systems in 5A1.
5A203 Test benches/stands, usable for complete rocket systems and subsystems (including ballistic missile systems, space launch vehicles and sounding rockets) which have the capacity to handle solid or liquid propellant rockets, motors or engines, or which are capable of simultaneously measuring the three axial thrust components.
5A204 Vibration test equipment (vibration test systems and vibration thrusters) and components using digital control techniques and feedback or closed loop test equipment and software thereof (Refer 4A006).
5A205 Flow-forming machines and specially designed components thereof which, according to the manufacturers technical specification,
1. can be equipped with numerical control units or a computer control, even when not equipped with such units at delivery; and
2. have more than two axes which can be coordinated simultaneously for contouring control.
Note 1: Item 5A205 includes machines which have only a single roller designed to deform metal plus two auxiliary rollers which support the mandrel, but do not participate directly in the deformation process.
Note 2: Item 5A205 does not include machines that are not usable in the "production" of propulsion components and equipment (e.g. motor cases and interstages) for systems specified in 5A and 5B.
Technical Note: Machines combining the function of spin-forming and flow-forming are, for the purpose of this item, regarded as flow-forming machines.
5A206 Filament winding machines or fibre placement machines for which the motion for positioning wrapping and winding fibres can be coordinated and programmed in two or more axes; precision mandrels thereof, and coordinating and programming controls.
5A207 Tape-laying machines of which the motions for positioning and laying tape and sheets can be coordinated and programmed in two or more axes;
5A208 Isostatic presses having all of the characteristics of maximum working pressure equal to or greater than 69 MPa or greater; designed to achieve and maintain a controlled thermal environment of 600oC or greater; and possessing a chamber cavity with an inside diameter of 152 mm or greater.
5A209 Environmental chambers simulating vibration environments, with altitudes equal to or greater than 15 km, or temperature ranging between minus 50 and plus 125 degrees centigrade.
5A210 Environmental chambers simulating acoustic pressure level of 140 dB or greater or rated acoustic power output of 4 KW or greater, with altitudes equal to or greater than 15 km, or temperature ranging between minus 50 and plus 125 degrees centigrade.
5A211 Accelerators delivering electro-magnetic radiation produced by Bremsstrahlung from accelerated electrons.
5A212 Pulsed electron accelerators
| 5A213 5A214 | Radial ball bearings having all tolerances specified in accordance with Class 2 or better and having all the following characteristics: a. An inner ring bore diameter between 12 and 50 mm; b. An outer ring outside diameter between 25 and 100 mm; and c. A width between 10 and 20 mm. Liquid propellant tanks specially designed for the propellants controlled in liquid propellants used in the systems specified in 5A and 5B. | ISO 492 Tolerance Item 3A3 or other |
5A215 Production facilities and production equipment specially designed for equipment or materials for 5A101 and 5A102.
Appendix 3 – SCOMET List
5A216 Production equipment and specially designed components thereof, for the production, handling or acceptance testing of liquid propellants or propellant constituents as referred in 3A3;
5A217 Launch and ground support equipment and facilities usable for rocket systems (including ballistic missile systems, space launch vehicles and sounding rockets), unmanned airborne system and cruise missiles as follows:-
a. apparatus, devices and vehicles, designed or modified for the transport, handling, control, activation and launching of the systems.
b. gravity meters (gravimeters), gravity gradiometers, and specially designed components thereof, designed or modified for airborne or marine use usable for complete rocket systems and for complete unmanned aerial vehicle systems (including cruise missile systems target drones and reconnaissance drones)
c. telemetry and tele-command equipment, including ground equipment, designed or modified for complete rocket systems and complete unmanned aerial vehicle systems and cruise missiles, excluding equipment designed or modified for manned aircraft or satellites, ground based equipment designed or modified for terrestrial or marine application, and equipment designed for commercial, civil or ‘safety of life’ (e.g. data integrity, flight safety) GNSS services.
d. radomes designed to withstand a combined thermal and pressure shock usable in protecting rocket systems, unmanned aerial vehicles and cruise missiles against nuclear effects (eg. electro-magnetic pulse (EMP), X-rays, combined blast and thermal effects).
e. Software which processes post-flight, recorded data, enabling determination of vehicle position throughout its flight path
f. Thermal batteries designed or modified for complete rocket systems of 5A or complete unmanned aerial vehicles of 5B
Note: ‘Thermal batteries’ are single use batteries that contain a solid non- conducting inorganic salt as the electrolyte. These batteries incorporate a pyrolytic material that, when
ignited, melts the electrolyte and activates the battery.
5A218 Systems, specially designed for radar cross section measurement, usable for rocket systems (including ballistic missile systems, space launch vehicles and sounding rockets), unmanned airborne system and cruise missiles and their subsystems.
5A3 Technology
5A301 Technology related to the development, production, testing and use of items in 5A1 and 5A2.
5A302 Software for the development, production, and testing and use of items in 5A1 and 5A2.
5A303 Software which coordinates the function of more than one subsystem, specially designed or modified for use in the systems specified in 5A1 and 5A2.
5B Unmanned aerial vehicles including cruise missiles, target drones and reconnaissance drones and related equipment, and specially designed components therefor:
a. Unmanned aerial vehicles including Remotely Piloted air Vehicles (RPVs) and autonomous programmable vehicles;
b. Associated launchers and ground support equipment;
c. Related equipment for command and control.
d. Complete unmanned aerial vehicle systems (including cruise missile systems, target drones and reconnaissance drones)
e. Light weight Turbojet and turbofan engines (including turbo compound engines).
f. Ramjet / Scramjet / pulse jet/ combined cycle engines, including devices to regulate Appendix 3 – SCOMET List
combustion, and specially designed components.
g. Complete unmanned aerial vehicle systems having an autonomous flight control and navigation capability or capability of controlled flight out of the direct vision range involving a human operator, designed or modified to incorporate an aerosol dispensation mechanism, or capable of carrying elements of a payload in the form of a particulate or
liquid other than fuel components of such vehicles.
Note: This category does not control unpowered airborne vehicles such as gliders, hot air balloons etc.
h. Safing, arming, fusing and firing mechanisms for weapons or warhead.
i Production facilities and Production equipment specially designed for equipment or materials for 5B.
j. Technology, for the development, production or use of equipment, materials or software specified for 5B.
k. Software, for the development, production or use of equipment or materials specified for 5B.
l. Software which coordinates the function of more than one subsystem, specially designed or
modified for use in the systems specified in 5B.
m. Turboprop engine systems’ specially designed for the systems in 5B.d, and specially designed components therefor, having a maximum power greater than 10 kW (achieved uninstalled at sea level standard conditions), excluding civil certified engines.
Note: For the purposes of this entry, a ‘turboprop engine system’ incorporates all of the following:
i. Turboshaft engine; and
ii. Power transmission system to transfer the power to a propeller.
5C Avionics and navigation systems designed or modified for use in, or usable in rocket systems (including ballistic missile systems, space launch vehicles and sounding rockets), unmanned aerial vehicles and cruise missiles
| 5C001 5C002 | Guidance systems and their components such as gyros and inertial reference units, and specially designed components therefor; Integrated flight instrument systems which include gyrostabilizers or automatic pilots, and specially designed components therefor; |
5C003 Compasses (including gyro-astro compasses), gyroscopes, accelerometers and inertial equipment and specially designed software thereof and specially designed components therefor.
5C004 Inertial or other equipment using accelerometers or systems incorporating such equipment, and specially designed integration software therefor;
5C005 Encrypted telemetry systems, equipment and software thereof.
5C006 Flight control system (including servo valves) designed or modified for the systems as follows:
a. Hydraulic, mechanical, electro-optical or electro-mechanical flight control systems (including fly-by-wire systems);
b. Attitude control equipment;
c. Design technology for integration of flight control, guidance, and propulsion data into a flight management system for optimisation of rocket system trajectory.
d. Specially designed test, calibration, and alignment thereof.
5C007 1. Integrated navigation system incorporating an inertial measurement device (example: an attitude and heading reference system, inertial reference unit, or inertial navigation system); one or more external sensor used to update the position and/or velocity, either periodically or continuously throughout the flight (example: satellite navigation receiver, radar altimeter and/or Doppler radar); integration hardware and software.
2. Three axis magnetic heading sensors having all of the following characteristics, and specially designed components therefor:
a. Internal tilt compensation in pitch (+/- 90 degrees) and having roll (+/- 180 degrees) axes.
Appendix 3 – SCOMET List
b. Capable of providing azimuthal accuracy better (less) than 0.5 degrees rms at latitudes of +/- 80 degrees, referenced to local magnetic field; and
c. Designed or modified to be integrated with flight control and navigation systems.
Note: Flight control and navigation systems in this item include gyrostabilizers, automatic pilots and inertial navigation systems.
5C008 Production equipment and other test, calibration and alignment equipment, designed or modified to be used with equipment specified in 5C001 – 5C004 and 5C007.
| 5C009 5C010 5C011 | Equipment used to characterize mirrors for laser gyros such as scatterometer, reflectometer and profilometer and for other inertial equipments such as Inertial measurement unit (IMU Module) tester, IMU Platform tester, IMU stable element handling fixture, Gyro tuning test station, Gyro dynamic balance station, Gyro run- in/motor test station, Gyro evacuation and filling station, Centrifuge fixture for gyro bearings, Accelerometer axis align station, Accelerometer test station and Fiber Optic Gyro Coil Winding Machines. Avionics equipment and embedded or specially designed software and components thereof, including but not limited to: a. Radar and laser radar system including altimeter; b. Electronic assemblies and components including umbilical and interstage electrical connectors Technical Note: Interstage connectors also include electrical connectors installed between systems and their payload. c. Design technology for protection of avionics and electrical subsystems against electromagnetic pulse (EMP) and electromagnetic interference (EMI) hazards from external sources. d. Passive sensors for determining bearings to electromagnetic sources (direction finding devices) or terrain characteristics e. Receiving equipment for Global Navigation Satellite Systems (GNSS: e.g. GPS, GLONASS, GALILEO), capable of operating at aircraft speeds and altitudes or above. f. Terrain contour mapping equipment, Scene mapping and correlation (both digital and analogue) equipment, Doppler navigation radar equipment, Passive interferometer equipment and Imaging sensor equipment (both active and passive) g. Design technology for electromagnetic shielding systems, the configuration of hardened electrical circuits and subsystems and for the determination of hardening criteria. On-board electronic equipment, devices and their design and manufacturing know-how (except warhead fuses, timers and sequencers), and embedded or specially designed software thereof. |
5C012 Detectors designed or modified, in protecting rocket systems, unmanned aerial vehicles and cruise missiles against nuclear effects (eg. electro-magnetic pulse (EMP), X-rays, combined blast and thermal effects).
5C013 Radiation Hardened microcircuits usable in protecting rocket systems, unmanned aerial vehicles and cruise missiles against nuclear effects (e.g. electro-magnetic pulse (EMP), X-rays, combined blast and thermal effects).
5C014 Precision tracking systems using a code translator installed on the rocket or unmanned aerial vehicle in conjunction with either surface or airborne references or navigation satellite systems to provide real-time measurement of inflight position and velocity; Range instrumentation radars including associated optical/infrared trackers and related software.
5C015 Balancing machines capable of balancing rotors/assemblies and correcting unbalance in two planes or more.
5C016 Indicator heads or balancing instrumentation designed or modified for use with balancing machines Appendix 3 – SCOMET List
5C017 Motion simulators or rate tables having all of the following characteristics:
a) Two axes or more;
b) Designed or modified to incorporate slip rings or integrated non-contact devices capable of
transferring electrical power, signal information, or both; and
c) Having any of the following characteristics:
1. For any single axis having all of the following:
a. Capable of rates of 400 degrees/s or more, or 30 degrees/s or less; and
b. A rate resolution equal to or less than 6 degrees/s and an accuracy equal to or less than 0.6 degrees/s;
2. Having a worst-case rate stability equal to or better (less) than plus or minus
0.05 % averaged over 10 degrees or more; or
3. A positioning ‘accuracy’ equal to or less (better) than 5 arc second.
Note 1: 5C017 does not control rotary tables designed or modified for machine tools or for medical equipment.
Note 2: Motion simulators or rate tables specified in 5C017 remain controlled whether or not slip
rings or integrated non-contact devices are fitted at time of export.
5C018 Position tables (equipment capable of precise rotary positioning in any axes) having two axes or
more and a position accuracy equal to or better than 5 arc second
5C019 Centrifuges capable of imparting accelerations above 100 g and designed or modified to incorporate slip rings or integrated non-contact devices capable of transferring electrical power, signal information, or both.
Note: Centrifuges specified in 5C019 remain controlled whether or not slip rings or integrated noncontact devices are fitted at time of export.
5C020 Design technology for integration of air vehicle fuselage, propulsion system and lifting control surfaces designed or modified for the unmanned aerial vehicle systems to optimize aerodynamic
performance throughout the flight regime of an unmanned aerial vehicle system
5C021 Design technology for integration of the flight control, guidance, and propulsion data into a flight management system, designed or modified for the complete rocket systems, unmanned aerial vehicles and cruise missiles for optimization of the trajectory.
5C022 Technology for the development, production, or use of items in 5C.
5C023 Software for the development, production and use of items in 5C.
5C024 Software specially designed or modified for use in the systems specified in 5C.
5D Manned-aircraft, aero-engines, related equipment and components:
Note: This category does not control foreign military aircraft or an Indian aircraft carrying a military registration number.
5D001 Combat aircraft and specially designed components thereof;
a. Other aircraft specially designed or modified for military use, including military reconnaissance, assault, military training, transporting and air-dropping troops or military equipment, logistics support, and specially designed components thereof;
b. Aero-engines specially designed or modified for military use, and specially designed components thereof;
c. Airborne equipment, including airborne refuelling equipment, specially designed for use with the aircraft controlled by 5D001a or 5D001b or the aero- engines controlled by
5D001c, and specially designed components thereof;
Appendix 3 – SCOMET List
d. Pressure refuellers, pressure refuelling equipment, equipment specially designed to facilitate operations in confined areas and ground equipment, developed specially for aircraft controlled by 5D001a or 5D001b or for aero-engines controlled by 5D001c;
e. Pressurized breathing equipment and partial pressure suits for use in aircraft anti-g suits, military crash helmets and protective masks, liquid oxygen converters used for aircraft or missiles, and catapults and cartridge actuated devices for emergency escape of personnel from aircraft;
f. Parachutes:
1. Paragliders, drag parachutes, drogue parachutes for stabilization and attitude control of
dropping bodies, (e.g. recovery capsules, ejection seats, bombs);
2. Drogue parachutes for use with ejection seat systems for deployment and inflation sequence regulation of emergency parachutes;
3. Recovery parachutes for guided missiles, drones or space vehicles;
4. Approach parachutes and landing deceleration parachutes.
g. Automatic piloting systems for parachuted loads, equipment specially designed or modified for military use for controlled opening jumps at any height, including oxygen equipment.
Note 1: 5D001b does not control aircraft or variants of those aircraft specially designed for military use which:
1. Have been certified for civil use by the civil aviation authority of India, and
2. Are not configured for military use and are not fitted with equipment or attachments specially designed or modified for military use;
Note 2: The control in 5D001b and 5D001c on specially designed components and related equipment for
non-military aircraft or aero-engines modified for military use applies
only to those military components and to military related equipment required for the modification to military use.
5E Microlight aircraft and powered ‘hang-gliders’
Appendix 3 – SCOMET List
Category 6 Munitions List
Note 1 Terms in "quotations" are defined terms. Refer to ‘Glossary’
Note 2 In some instances chemicals are listed by name and CAS number. The list applies to chemicals of the same structural formula (including hydrates) regardless of name or CAS number. CAS numbers are shown to assist in identifying a particular chemical or mixture, irrespective of nomenclature. CAS numbers cannot be used as unique identifiers because some forms of the listed chemical have different CAS numbers, and mixtures containing a listed chemical may also have different CAS numbers.
Note 3 Subject to Notes 4-6 below, an authorization from Department of Defence Production, Ministry of Defence would be required for export of items in this Munitions list. This is as per the Standard
Operating Procedures issued by Department of Defence Production.
Note 4 Notwithstanding anything contained in Note 3 above, the following items will be classified under the relevant description in category 0 and would be subject to authorisation by Department of Atomic
Energy(refer a) to d) of Commodity Identification Note 2 of SCOMET):-
a) Radioactive materials covered under 6A007;
b) 'Reactive material' powders and shapes and any material containing Beryllium or “Zirconium with Hafnium content less than 2000 ppm” as the major constituent covered under 6A008;
c) Nuclear power generating equipment or propulsion equipment, including "nuclear reactors", and specially designed for military use and components therefor specially designed or
'modified for military use’ covered under 6A017;
d) Simulators specially designed for military "nuclear reactors" covered under 6A017;
Note 5 Notwithstanding anything contained in Note 3 above, items corresponding to Schedule I of the Chemical Weapons Convention as specified in Category 6A007.b are prohibited for exports.
Note 6 Notwithstanding anything contained in Note 3 above, licence applications for Items in 6A008 a.13 and 6A008.a 21 would normally be denied.
6A001 Smooth-bore weapons with a calibre of less than 20 mm, other arms and automatic weapons with a calibre of
12.7 mm (calibre 0.50 inches) or less and accessories, as follows, and specially designed components therefor:
Note 6A001 does not apply to:
a. Firearms specially designed for dummy ammunition and which are incapable of discharging a projectile;
b. Firearms specially designed to launch tethered projectiles having no high explosive charge or
communications link, to a range of less than or equal to 500 m;
c. Weapons using non-centre fire cased ammunition and which are not of the fully automatic firing type;
d. "Deactivated firearms".
6A001 a. Rifles and combination guns, handguns, machine, sub-machine and volley guns;
Note 6A001.a does not apply to the following:
a. Rifles and combination guns, manufactured earlier than 1938;
b. Reproductions of rifles and combination guns, the originals of which were manufactured earlier than 1890;
c. Handguns, volley guns and machine guns, manufactured earlier than 1890, and their reproductions;
d. Rifles or handguns, specially designed to discharge an inert projectile by compressed air or CO2.
6A001 b. Smooth-bore weapons as follows:
1. Smooth-bore weapons specially designed for military use;
2. Other smooth-bore weapons as follows:
a. Fully automatic type weapons;
Appendix 3 – SCOMET List
b. Semi-automatic or pump-action type weapons;
Note 6A001.b.2 does not apply to weapons specially designed to discharge an inert projectile by compressed air or CO2.
Note 6A001.b. does not apply to the following:
a. Smooth-bore weapons manufactured earlier than 1938;
b. Reproductions of smooth-bore weapons, the originals of which were manufactured earlier than 1890.
c. Smooth-bore weapons used for hunting or sporting purposes. These weapons must not be specially designed for military use or of the fully automatic firing type;
d. Smooth-bore weapons specially designed for any of the following:
1. Slaughtering of domestic animals;
2. Tranquilizing of animals;
3. Seismic testing;
4. Firing of industrial projectiles; or
5. Disrupting Improvised Explosive Devices (IEDs).
N.B. For disruptors, see 6A004 and 8A106.
6A001 c. Weapons using caseless ammunition;
6A001 d. Detachable cartridge magazines, sound suppressors or moderators, special gun-mountings, optical weaponsights and flash suppressors, for arms specified by 6A001.a, 6A001.b, or 6A001.c.
Note 6A001.d does not apply to optical weapon-sights without electronic image processing, with a magnification of 9 times or less, provided they are not specially designed or modified for military use, or incorporate any reticles specially designed for military use.
6A002 Smooth-bore weapons with a calibre of 20 mm or more, other weapons or armament with a calibre greater than
12.7 mm (calibre 0.50 inches), projectors and accessories, as follows, and specially designed components therefor:
a. Guns, howitzers, cannon, mortars, anti-tank weapons, projectile launchers, military flame throwers, rifles, recoilless rifles, smooth-bore weapons and signature reduction devices therefor;
Note 1 6A002.a includes injectors, metering devices, storage tanks and other specially designed components for use with liquid propelling charges for any of the equipment specified by 6A002.a.
Note 2 6A002.a does not apply to weapons as follows:
a. Rifles, smooth-bore weapons and combination guns, manufactured earlier than 1938;
b. Reproductions of rifles, smooth-bore weapons and combination guns, the originals of
which were manufactured earlier than 1890;
c. Guns, howitzers, cannons, mortars, manufactured earlier than 1890;
d. Smooth-bore weapons used for hunting or sporting purposes. These weapons must not be specially designed for military use or of the fully automatic firing type;
e. Smooth-bore weapons specially designed for any of the following:
1. Slaughtering of domestic animals;
2. Tranquilizing of animals;
3. Seismic testing;
4. Firing of industrial projectiles; or
5. Disrupting Improvised Explosive Devices (IEDs);
N.B. For disruptors, see 6A004 and 8A106
f. Hand-held projectile launchers specially designed to launch tethered projectiles having no high explosive charge or communications link, to a range of less than or equal to 500 m.
6A002 b. Smoke, gas and pyrotechnic projectors or generators, specially designed or modified for military use;
Note 6A002.b does not apply to signal pistols.
Appendix 3 – SCOMET List
6A002 c. Weapons sights and weapon sight mounts, having all of the following:
1. Specially designed for military use; and
2. Specially designed for weapons specified in 6A002.a;
6A002 d. Mountings and detachable cartridge magazines, specially designed for the weapons specified in 6A002.a.
6A003 a. Ammunition and fuze setting devices, as follows, and specially designed components therefor:
b. Ammunition for weapons specified by 6A001, 6A002, or 6A012;
c. Fuze setting devices specially designed for ammunition specified by 6A003.a.
Note 1 Specially designed components specified by 6A003 include:
a. Metal or plastic fabrications such as primer anvils, bullet cups, cartridge links, rotating bands and munitions metal parts;
b. Safing and arming devices, fuzes, sensors and initiation devices ;
c. Power supplies with high one-time operational output;
d. Combustible cases for charges;
e. Submunitions including bomblets, minelets and terminally guided projectiles.
Note 2 6A003.a does not apply to any of the following:
a. Ammunition crimped without a projectile (blank star);
b. Dummy ammunition with a pierced powder chamber;
c. Other blank and dummy ammunition, not incorporating components designed for live ammunition; or
d. Components specially designed for blank or dummy ammunition, specified in this Note 2.a, b. or c.
Note 3 6A003.a does not apply to cartridges specially designed for any of the following purposes:
a. Signalling;
b. Bird scaring; or
c. Lighting of gas flares at oil wells.
6A004 Bombs, torpedoes, rockets, missiles, other explosive devices and charges and
related equipment and accessories, as follows, and specially designed
components therefor:
N.B.1. For guidance and navigation equipment, see 6A011.
N.B.2. For Aircraft Missile Protection Systems (AMPS), see 6A004.c.
6A004 a. Bombs, torpedoes, grenades, smoke canisters, rockets, mines, missiles, depth charges, demolitioncharges, demolition-devices, demolition-kits, "pyrotechnic" devices, cartridges and simulators (i.e, equipment simulating the characteristics of any of these items), specially designed for military use;
Note 6A004.a includes:
a. Smoke grenades, fire bombs, incendiary bombs and explosive devices;
b. Missile rocket nozzles and re-entry vehicle nosetips.
6A004 b. Equipment having all of the following:
1. Specially designed for military use; and
2. Specially designed for 'activities' relating to any of the following:
a. Items specified by 6A004.a; or
b. Improvised Explosive Devices (IEDs).
Technical Note
For the purpose of 6A004.b.2 'activities' applies to handling, launching, laying, controlling, discharging, detonating, activating, powering with one-time operational output, decoying, jamming, sweeping, detecting, disrupting or disposing.
Note 1 6A004.b includes:
a. Mobile gas liquefying equipment capable of producing 1,000 kg or more per day of gas in liquid form;
b. Buoyant electric conducting cable suitable for sweeping magnetic mines.
Note 2 6A004.b does not apply to hand-held devices limited by design solely to the detection of metal objects and incapable of distinguishing between mines and other metal objects.
Appendix 3 – SCOMET List
6A004. c. Aircraft Missile Protection Systems (AMPS).
Note 6A004.c does not apply to AMPS having all of the following:
a. Any of the following missile warning sensors:
1. Passive sensors having peak response between 100-400 nm; or
2. Active pulsed Doppler missile warning sensors;
b. Countermeasures dispensing systems;
c. Flares, which exhibit both a visible signature and an infrared signature, for decoying surface-to-air missiles; and
d. Installed on "civil aircraft" and having all of the following:
1. The AMPS is only operable in a specific "civil aircraft" in which the specific AMPS is installed and for which any of the following has been issued:
a. A civil Type Certificate issued by civil aviation authority of India; or
b. An equivalent document recognised by the International Civil Aviation Organisation (ICAO);
2. The AMPS employs protection to prevent unauthorised access to "software"; and
3. The AMPS incorporates an active mechanism that forces the system not to function when it is removed from the "civil aircraft" in which it was installed.
6A005 Fire control, and related alerting and warning equipment, and related systems, test and alignment and countermeasure equipment, as follows, specially designed for military use, and specially designed components and accessories therefor:
a. Weapon sights, bombing computers, gun laying equipment and weapon control systems;
b. Target acquisition, designation, range-finding, surveillance or tracking systems; detection, data fusion,
recognition or identification equipment; and sensor integration equipment;
c. Countermeasure equipment for items specified by 6A005.a or 6A005.b;
Note For the purposes of 6A005.c, countermeasure equipment includes detection equipment.
d. Field test or alignment equipment, specially designed for items specified by 6A005.a, 6A005.b, or 6A005.c.
Appendix 3 – SCOMET List
6A006 Ground vehicles and components, as follows:
N.B. For guidance and navigation equipment, see 6A011.
a. Ground vehicles and components therefor, specially designed or modified for military use; Technical Note
For the purposes of 6A006.a the term ground vehicles includes trailers.
6A006 b. Other ground vehicles and components, as follows:
1. Vehicles having all of the following:
a. Manufactured or fitted with materials or components to provide ballistic protection to level III (NIJ 0108.01, September 1985) or better;
b. A transmission to provide drive to both front and rear wheels simultaneously, including those vehicles having additional wheels for load bearing purposes whether driven or not;
c. Gross Vehicle Weight Rating (GVWR) greater than 4,500 kg; and
d. Designed or modified for off-road use;
e. Mine-Protected vehicles
2. Components having all of the following:
a. Specially designed for vehicles specified in 6A006.b.1; and
b. Providing ballistic protection to level III (NIJ 0108.01, September 1985) or better.
N.B. See also 6A013.a.
Note 1 6A006.a includes:
a. Tanks and other military armed vehicles and military vehicles fitted with mountings for arms or equipment for mine laying or the launching of munitions specified by 6A004;
b. Armoured vehicles;
c. Amphibious and deep water fording vehicles;
d. Recovery vehicles and vehicles for towing or transporting ammunition or weapon systems and
associated load handling equipment.
Note 2 Modification of a ground vehicle for military use specified by 6A006.a entails a structural, electrical or mechanical change involving one or more components that are specially designed for military use. Such components include:
a. Pneumatic tyre casings of a kind specially designed to be bullet-proof;
b. Armoured protection of vital parts (e.g, fuel tanks or vehicle cabs);
c. Special reinforcements or mountings for weapons;
d. Black-out lighting.
Note 3 6A006 does not apply to civil vehicles designed or modified for transporting money or valuables.
Note 4 6A006 does not apply to vehicles that meet all of the following;
a. Were manufactured before 1946;
b. Do not have items specified in category 6 and manufactured after 1945, except for reproductions of original components or accessories for the vehicle; and
c. Do not incorporate weapons specified in 6A001, 6A002, or 6A004 unless they are inoperable
and incapable of discharging a projectile.
Note 5 6A006.b does not include soft skinned vehicles i.e. the vehicles which are neither armoured nor intended to be modified as an armoured vehicle in future.
Appendix 3 – SCOMET List
6A007 Chemical agents, "biological agents", "riot control agents", radioactive materials, related equipment, components and materials, as follows:
N.B (See Commodity Identification Note of SCOMET list)
a. "Biological agents" or radioactive materials selected or modified to increase their effectiveness in producing casualties in humans or animals, degrading equipment or damaging crops or the environment;
b. Chemical warfare (CW) agents including:
1. CW nerve agents:
a. O-Alkyl (equal to or less than C10, including cycloalkyl) alkyl (Methyl, Ethyl, n-Propyl or Isopropyl) - phosphonofluoridates, such as:
Sarin (GB):O-Isopropyl methylphosphonofluoridate (CAS 107-44-8); and
Soman (GD):O-Pinacolyl methylphosphonofluoridate (CAS 96-64-0);
b. O-Alkyl (equal to or less than C10, including cycloalkyl)
N,N-dialkyl (Methyl, Ethyl, n-Propyl or Isopropyl) phosphoramidocyanidates, such as: Tabun
(GA):O-Ethyl
N,N-dimethylphosphoramidocyanidate (CAS 77-81-6);
c. O-Alkyl (H or equal to or less than C10, including cycloalkyl)
S-2-dialkyl (Methyl, Ethyl, n-Propyl or Isopropyl)-aminoethyl alkyl (Methyl, Ethyl, n-Propyl or Isopropyl) phosphonothiolates and corresponding alkylated and protonated salts, such as: VX: O-Ethyl S-2-diisopropylaminoethyl methyl phosphonothiolate (CAS 50782-69-9);
| 6A007 6A007 6A007 | b. b. b. | 2. a. b. c. 3. a. 4. a. b. | CW vesicant agents: Sulphur mustards, such as: 1. 2-Chloroethylchloromethylsulphide (CAS 2625-76-5); 2. Bis(2-chloroethyl) sulphide (CAS 505-60-2); 3. Bis(2-chloroethylthio) methane (CAS 63869-13-6); 4. 1,2-bis (2-chloroethylthio) ethane (CAS 3563-36-8); 5. 1,3-bis (2-chloroethylthio) -n-propane (CAS 63905-10-2); 6. 1,4-bis (2-chloroethylthio) -n-butane (CAS 142868-93-7) ; 7. 1,5-bis (2-chloroethylthio) -n-pentane (CAS 142868-94-8); 8. Bis (2-chloroethylthiomethyl) ether (CAS 63918-90-1); 9. Bis (2-chloroethylthioethyl) ether (CAS 63918-89-8); Lewisites, such as: 1. 2-chlorovinyldichloroarsine (CAS 541-25-3); 2. Tris (2-chlorovinyl) arsine (CAS 40334-70-1); 3. Bis (2-chlorovinyl) chloroarsine (CAS 40334-69-8); Nitrogen mustards, such as: 1. HN1: bis (2-chloroethyl) ethylamine (CAS 538-07-8); 2. HN2: bis (2-chloroethyl) methylamine (CAS 51-75-2); 3. HN3: tris (2-chloroethyl) amine (CAS 555-77-1); CW incapacitating agents, such as: 3-Quinuclidinyl benzilate (BZ) (CAS 6581-06-2); CW defoliants, such as: Butyl 2-chloro-4-fluorophenoxyacetate (LNF); 2,4,5-trichlorophenoxyacetic acid (CAS 93-76-5) mixed with 2,4-dichlorophenoxyacetic acid (CAS 94-75-7) (Agent Orange (CAS 39277-47-9)); |
6A007 c. CW binary precursors and key precursors, as follows:
1. Alkyl (Methyl, Ethyl, n-Propyl or Isopropyl) Phosphonyl Difluorides, such as: DF: Methyl Phosphonyldifluoride (CAS 676-99-3);
2. O-Alkyl (H or equal to or less than C10, including cycloalkyl) O-2-dialkyl (Methyl, Ethyl, n- Propyl or Isopropyl)-aminoethyl alkyl (Methyl, Ethyl, n-Propyl or Isopropyl) phosphonites and corresponding alkylated and protonated salts, such as:
Appendix 3 – SCOMET List
QL: O-Ethyl O-2-di-isopropylaminoethyl methylphosphonite (CAS 57856-11-8);
3. Chlorosarin: O-Isopropyl methylphosphonochloridate (CAS 1445-76-7);
4. Chlorosoman: O-Pinacolyl methylphosphonochloridate (CAS 7040-57-5);
6A007 d. "Riot control agents", active constituent chemicals and combinations thereof, including:
1. -Bromobenzeneacetonitrile, (Bromobenzyl cyanide) (CA) (CAS 5798-79-8);
2. [(2-chlorophenyl) methylene] propanedinitrile,
(o-Chlorobenzylidenemalononitrile) (CS) (CAS 2698-41-1);
3. 2-Chloro-1-phenylethanone, Phenylacyl chloride (-chloroacetophenone) (CN) (CAS 532-27-4);
4. Dibenz-(b,f)-1,4-oxazephine, (CR) (CAS 257-07-8);
5. 10-Chloro-5,10-dihydrophenarsazine, (Phenarsazine chloride), (Adamsite), (DM) (CAS 578- 94-9);
6. N-Nonanoylmorpholine, (MPA) (CAS 5299-64-9);
Note 1 6A007.d does not apply to "riot control agents" individually packaged for personal self-defence purposes.
Note 2 6A007.d does not apply to active constituent chemicals, and combinations thereof, identified and packaged for food production or medical purposes.
6A007 e. Equipment, specially designed or modified for military use, designed or modified for the dissemination of any of the following, and specially designed components therefor:
1. Materials or agents specified by 6A007.a, 6A007.b, or 6A007.d;or
2. CW agents made up of precursors specified by 6A007.c;
6A007 f. Protective and decontamination equipment, specially designed or modified for military use, components and chemical mixtures, as follows:
1. Equipment designed or modified for defence against materials specified by 6A007.a, 6A007.b, or 6A007.d, and specially designed components therefor;
2. Equipment designed or modified for decontamination of objects contaminated with materials
specified by 6A007.a, or 6A007.b, and specially designed components therefor;
3. Chemical mixtures specially developed or formulated for the decontamination of objects contaminated with materials specified by 6A007.a or 6A007.b;
Note 6A007.f.1 includes:
a. Air conditioning units specially designed or modified for nuclear, biological or chemical filtration;
b. Protective clothing.
N.B. For civil gas masks, protective and decontamination equipment, see also 8A104.
| 6A007 Note N.B. | g. Equipment, specially designed or modified for military use designed or modified for the detection or identification of materials specified by 6A007.a, 6A007.b, or 6A007.d, and specially designed components therefor; 6A007.g does not apply to personal radiation monitoring dosimeters. See also 8A104. |
| 6A007 6A007 Note Note | h. "Biopolymers" specially designed or processed for the detection or identification of CW agents specified by 6A007.b, and the cultures of specific cells used to produce them; i. "Biocatalysts" for the decontamination or degradation of CW agents, and biological systems therefor, as follows: 1. "Biocatalysts" specially designed for the decontamination or degradation of CW agents specified by 6A007.b, and resulting from directed laboratory selection or genetic manipulation of biological systems; 2. Biological systems containing the genetic information specific to the production of Appendix 3 – SCOMET List "biocatalysts" specified by 6A007.i.1, as follows: a. "Expression vectors"; b. Viruses; c. Cultures of cells. 1 6A007.b and 6A007.d do not apply to the following: a. Cyanogen chloride (CAS 506-77-4); b. Hydrocyanic acid (CAS 74-90-8); c. Chlorine (CAS 7782-50-5); d. Carbonyl chloride (phosgene) (CAS 75-44-5); e. Diphosgene (trichloromethyl-chloroformate) (CAS 503-38-8); f. ((Reserved)) g. Xylyl bromide, ortho: (CAS 89-92-9), meta: (CAS 620-13-3), para: (CAS 104-81-4); h. Benzyl bromide (CAS 100-39-0); i. Benzyl iodide (CAS 620-05-3); j. Bromo acetone (CAS 598-31-2); k. Cyanogen bromide (CAS 506-68-3); l. Bromo methylethylketone (CAS 816-40-0); m. Chloro acetone (CAS 78-95-5); n. Ethyl iodoacetate (CAS 623-48-3); o. Iodo acetone (CAS 3019-04-3); p. Chloropicrin (CAS 76-06-2). 2 The cultures of cells and biological systems specified by 6A007.h and 6A007.i.2 are exclusive and these sub-items do not apply to cells or biological systems for civil purposes, such as agricultural, pharmaceutical, medical, veterinary, environmental, waste management, or in the food industry. |
6A008 "Energetic materials" and related substances, as follows:
N.B.1. See also 8C111.
N.B.2. For charges and devices, see 6A004 and 8A108.
Technical Notes
1. For the purposes of 6A008, excluding 6A008.c.11, or 6A008.c.12, 'mixture' refers to a composition of two or more substances with at least one substance being listed in the 6A008 sub-items.
2. Any substance listed in the 6A008 sub-items is subject to this list, even when utilised in an application other than that indicated. (e.g, TAGN is predominantly used as an explosive but can also be used either as a fuel or an oxidizer.)
3. For the purposes of 6A008, particle size is the mean particle diameter on a weight or volume basis. International standards will be used in sampling and determining particle size.
6A008 a. "Explosives" as follows, and 'mixtures' thereof:
1. ADNBF (aminodinitrobenzofuroxan or 7-amino-4,6-dinitrobenzofurazane-1-oxide) (CAS 97096-78-
1);
2. BNCP (cis-bis (5-nitrotetrazolato) tetra amine-cobalt (III) perchlorate)
(CAS 117412-28-9);
3. CL-14 (diamino dinitrobenzofuroxan or 5,7-diamino-4,6-dinitrobenzofurazane-1-oxide ) (CAS 117907-74-1);
4. CL-20 (HNIW or Hexanitrohexaazaisowurtzitane) (CAS 135285-90-4); chlathrates of CL-20 (see also 6A008.g.3. and g.4. for its "precursors");
5. CP (2-(5-cyanotetrazolato) penta amine-cobalt (III) perchlorate) (CAS 70247-32-4);
6. DADE (1,1-diamino-2,2-dinitroethylene, FOX7) (CAS 145250-81-3);
7. DATB (diaminotrinitrobenzene) (CAS 1630-08-6);
8. DDFP (1,4-dinitrodifurazanopiperazine);
9. DDPO (2,6-diamino-3,5-dinitropyrazine-1-oxide, PZO) (CAS 194486-77-6);
10. DIPAM (3,3-diamino-2,2,4,4,6,6-hexanitrobiphenyl or dipicramide) (CAS 17215-44-0);
Appendix 3 – SCOMET List
11. DNGU (DINGU or dinitroglycoluril) (CAS 55510-04-8);
12. Furazans as follows:
a. DAAOF (DAAF, DAAFox, or diaminoazoxyfurazan);
b. DAAzF (diaminoazofurazan) (CAS 78644-90-3);
13. HMX and derivatives (see also 6A008.g.5. for its "precursors"), as follows:
a. HMX (Cyclotetramethylenetetranitramine, octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazine, 1,3,5,7-
tetranitro-1,3,5,7-tetraza-cyclooctane, octogen or octogene) (CAS 2691-41-0);
b. difluoroaminated analogs of HMX;
c. K-55 (2,4,6,8-tetranitro-2,4,6,8-tetraazabicyclo [3,3,0]-octanone-3, tetranitrosemiglycouril or keto-bicyclic HMX) (CAS 130256-72-3);
14. HNAD (hexanitroadamantane) (CAS 143850-71-9);
15. HNS (hexanitrostilbene) (CAS 20062-22-0);
16. Imidazoles as follows:
a. BNNII (Octahydro-2,5-bis(nitroimino)imidazo [4,5-d]imidazole);
b. DNI (2,4-dinitroimidazole) (CAS 5213-49-0);
c. FDIA (1-fluoro-2,4-dinitroimidazole);
d. NTDNIA (N-(2-nitrotriazolo)-2,4-dinitroimidazole);
e. PTIA (1-picryl-2,4,5-trinitroimidazole);
6A008 a. 17. NTNMH (1-(2-nitrotriazolo)-2-dinitromethylene hydrazine);
18. NTO (ONTA or 3-nitro-1,2,4-triazol-5-one) (CAS 932-64-9);
19. Polynitrocubanes with more than four nitro groups;
20. PYX (2,6-Bis(picrylamino)-3,5-dinitropyridine) (CAS 38082-89-2);
21. RDX and derivatives, as follows:
a. RDX (cyclotrimethylenetrinitramine, cyclonite, T4,
hexahydro-1,3,5-trinitro-1,3,5-triazine, 1,3,5-trinitro-1,3,5-
triaza-cyclohexane, hexogen or hexogene) (CAS 121-82-4);
b. Keto-RDX (K-6 or 2,4,6-trinitro-2,4,6-triazacyclohexanone)
(CAS 115029-35-1);
22. TAGN (triaminoguanidinenitrate) (CAS 4000-16-2);
23. TATB (triaminotrinitrobenzene) (CAS 3058-38-6) (see also 6A008.g.7 for its "precursors");
24. TEDDZ (3,3,7,7-tetrabis(difluoroamine) octahydro-1,5-dinitro-1,5-
diazocine);
25. Tetrazoles as follows:
a. NTAT (nitrotriazol aminotetrazole);
b. NTNT (1-N-(2-nitrotriazolo)-4-nitrotetrazole);
26. Tetryl (trinitrophenylmethylnitramine) (CAS 479-45-8);
27. TNAD (1,4,5,8-tetranitro-1,4,5,8-tetraazadecalin) (CAS 135877-16-6)
(see also 6A008.g.6. for its "precursors");
28. TNAZ (1,3,3-trinitroazetidine) (CAS 97645-24-4)
(see also 6A008.g.2. for its "precursors");
29. TNGU (SORGUYL or tetranitroglycoluril) (CAS 55510-03-7);
30. TNP (1,4,5,8-tetranitro-pyridazino[4,5-d]pyridazine) (CAS 229176-
04-9);
31. Triazines as follows:
a. DNAM (2-oxy-4,6-dinitroamino-s-triazine) (CAS 19899-80-0);
b. NNHT (2-nitroimino-5-nitro-hexahydro-1,3,5-triazine)
(CAS 130400-13-4);
32. Triazoles as follows:
a. 5-azido-2-nitrotriazole;
b. ADHTDN (4-amino-3,5-dihydrazino-1,2,4-triazole dinitramide) (CAS 1614-08-0);
c. ADNT (1-amino-3,5-dinitro-1,2,4-triazole);
d. BDNTA ((bis-dinitrotriazole)amine);
e. DBT (3,3-dinitro-5,5-bi-1,2,4-triazole) (CAS 30003-46-4);
f. DNBT (dinitrobistriazole) (CAS 70890-46-9);
g. (Reserved)
Appendix 3 – SCOMET List
h. NTDNT (1-N-(2-nitrotriazolo) 3,5-dinitrotriazole);
i. PDNT (1-picryl-3,5-dinitrotriazole);
j. TACOT (tetranitrobenzotriazolobenzotriazole) (CAS 25243-
36-1);
33. Explosives not listed elsewhere in 6A008.a and having any of the
following:
a. Detonation velocity exceeding 8,700 m/s, at maximum density, or
b. Detonation pressure exceeding 34 GPa (340 kbar);
34. (Reserved)
35. DNAN (2,4-dinitroanisole) (CAS 119-27-7);
36. TEX (4,10-Dinitro-2,6,8,12-tetraoxa-4,10-diazaisowurtzitane)
37. GUDN (Guanylurea dinitramide) FOX-12 (CAS 217464-38-5)
38. Tetrazines as follows:
a. BTAT (Bis(2,2,2-trinitroethyl)-3,6-diaminotetrazine);
b. LAX-112 (3,6-diamino-1,2,4,5-tetrazine-1,4-dioxide);
39. Energetic ionic materials melting between 343 K (70°C) and 373 K
(100°C) and with detonation velocity exceeding 6,800 m/s or detonation pressure exceeding 18 GPa (180 kbar);
40. BTNEN (Bis(2,2,2-trinitroethyl)-nitramine) (CAS 19836-28-3);
41. FTDO (5,6-(3',4'-furazano)- 1,2,3,4-tetrazine-1,3-dioxide);
Note 6A008.a includes 'explosive co-crystals'.
Technical Note
An 'explosive co-crystal' is a solid material consisting of an ordered three dimensional arrangement of two or more explosive molecules, where at least one is specified in 6A008.a.
6A008 b. "Propellants" as follows:
1. Any solid "propellant" with a theoretical specific impulse (under standard conditions) of more than:
a. 240 seconds for non-metallized, non-halogenized "propellant";
b. 250 seconds for non-metallized, halogenized "propellant"; or
c. 260 seconds for metallized "propellant";
2. (Reserved)
3. "Propellants" having a force constant of more than 1,200 kJ/kg;
4. "Propellants" that can sustain a steady-state linear burning rate of more than 38 mm/s under standard conditions (as measured in the form of an inhibited single strand) of 6.89 MPa (68.9 bar) pressure and 294K (21oC);
5. Elastomer Modified Cast Double Base (EMCDB) "propellants" with extensibility at maximum stress of more than 5% at 233K (-40oC);
6. Any "propellant" containing substances specified by 6A008.a;
7. "Propellants", not specified elsewhere in Category 6, specially designed for military use;
6A008. c. "Pyrotechnics", fuels and related substances, as follows, and 'mixtures' thereof:
1. "Aircraft" fuels specially formulated for military purposes;
Note "Aircraft" fuels specified by 6A008.c.1 are finished products, not their constituents.
2. Alane (aluminium hydride) (CAS 7784-21-6);
3. Boranes, as follows, and their derivatives:
a. Carboranes;
b. Borane homologues, as follows:
1. Decaborane (14) (CAS 17702-41-9);
2. Pentaborane (9) (CAS 19624-22-7);
3. Pentaborane (11) (CAS 18433-84-6);
4. Hydrazine and derivatives, as follows (see also 6A008.d.8. and d.9. for oxidising hydrazine derivatives):
a. Hydrazine (CAS 302-01-2) in concentrations of 70% or more;
b. Monomethyl hydrazine (CAS 60-34-4);
c. Symmetrical dimethyl hydrazine (CAS 540-73-8);
d. Unsymmetrical dimethyl hydrazine (CAS 57-14-7);
Appendix 3 – SCOMET List
Note 6A008.c.4.a does not apply to hydrazine 'mixtures' specially formulated for corrosion control.
| 6A008 c. | 5. Metal fuels, fuel 'mixtures' or "pyrotechnic" 'mixtures', in particle form whether spherical, atomized, spheroidal, flaked or ground, manufactured from material consisting of 99 % or more of any of the following: a. Metals as follows and 'mixtures' thereof: 1. Beryllium (CAS 7440-41-7) in particle sizes of less than 60 µm; 2. Iron powder (CAS 7439-89-6) with particle size of 3 µm or less produced by reduction of iron oxide with hydrogen; b. 'Mixtures' containing any of the following: 1. Zirconium (CAS 7440-67-7), magnesium (CAS 7439-95-4) or alloys of these in particle sizes of less than 60 µm; or 2. Boron (CAS 7440-42-8) or boron carbide (CAS 12069-32-8) fuels of 85% purity or higher and particle sizes of less than 60 µm; Note 1 6A008.c.5 applies to "explosives" and fuels, whether or not the metals or alloys are encapsulated in aluminium, magnesium, zirconium, or beryllium. Note 2 6A008.c.5.b only applies to metal fuels in particle form when they are mixed with other substances to form a 'mixture' formulated for military purposes such as liquid "propellant" slurries, solid "propellants", or "pyrotechnic" 'mixtures'. Note 3 6A008.c.5.b.2 does not apply to boron and boron carbide enriched with boron-10 (20% or more of total boron-10 content.) |
| 6A008 c. | 6. Military materials, containing thickeners for hydrocarbon fuels, specially formulated for use in flame throwers or incendiary munitions, such as metal stearates (e.g, octal (CAS 637-12-7)) or palmitates; 7. Perchlorates, chlorates and chromates, composited with powdered metal or other high energy fuel components; 8. Spherical or spheroidal aluminium powder (CAS 7429-90-5) with a particle size of 60 µm or less and manufactured from material with an aluminium content of 99% or more; 9. Titanium subhydride (TiHn) of stoichiometry equivalent to n= 0.65-1.68; 10. Liquid high energy density fuels not specified in 6A008.c.1, as follows: a. Mixed fuels, that incorporate both solid and liquid fuels (e.g, boron slurry), having a mass-based energy density of 40 MJ/kg or greater; b. Other high energy density fuels and fuel additives (e.g, cubane, ionic solutions, JP-7, JP-10), having a volume-based energy density of 37.5 GJ per cubic meter or greater, measured at 293 K (20⁰C) and one atmosphere (101.325 kPa) pressure; Note 6A008.c.10.b does not apply to JP-4, JP-8, fossil refined fuels or biofuels, or fuels for engines certified for use in civil aviation. |
| 6A008 c. | 11. "Pyrotechnic" and pyrophoric materials as follows: a. "Pyrotechnic" or pyrophoric materials specifically formulated to enhance or control the production of radiated energy in any part of the IR spectrum; b. Mixtures of magnesium, polytetrafluoroethylene (PTFE) and a vinylidene difluoride- hexafluoropropylene copolymer (e.g, MTV); |
| 12. | Fuel mixtures, "pyrotechnic" mixtures or "energetic materials", not specified elsewhere in 6A008, having all of the following: a. Containing greater than 0.5% of particles of any of the following: 1. Aluminium; 2. Beryllium; 3. Boron; 4. Zirconium; 5. Magnesium; or 6. Titanium; b. Particles specified by 6A008.c.12.a with a size less than 200 nm in any direction; and c. Particles specified by 6A008.c.12.a with a metal content of 60% or greater; |
| 6A008 d. | Oxidizers as follows, and 'mixtures' thereof: Appendix 3 – SCOMET List |
| 1. | ADN (ammonium dinitramide or SR 12) (CAS 140456-78-6); |
| 2. | AP (ammonium perchlorate) (CAS 7790-98-9); |
| 3. | Compounds composed of fluorine and any of the following: a. Other halogens; b. Oxygen; or c. Nitrogen; Note 1 6A008.d.3 does not apply to chlorine trifluoride (CAS 7790-91-2). Note 2 6A008.d.3 does not apply to nitrogen trifluoride (CAS 7783-54-2) in its gaseous state. |
| 4. | DNAD (1,3-dinitro-1,3-diazetidine) (CAS 78246-06-7); |
| 5. | HAN (hydroxylammonium nitrate) (CAS 13465-08-2); |
| 6. | HAP (hydroxylammonium perchlorate) (CAS 15588-62-2); |
| 7. | HNF (hydrazinium nitroformate) (CAS 20773-28-8); |
| 8. | Hydrazine nitrate (CAS 37836-27-4); |
| 9. | Hydrazine perchlorate (CAS 27978-54-7); |
| 10. | Liquid oxidisers comprised of or containing inhibited red fuming nitric acid (IRFNA) (CAS 8007-58- 7); Note 6A008.d.10 does not apply to non-inhibited fuming nitric acid. |
6A008 e. Binders, plasticizers, monomers and polymers, as follows:
1. AMMO (azidomethylmethyloxetane and its polymers) (CAS 90683-29-7)
(see also 6A008.g.1. for its "precursors");
2. BAMO (3,3-bis(azidomethyl)oxetane and its polymers)
(CAS 17607-20-4) (see also 6A008.g.1. for its "precursors");
3. BDNPA (bis (2,2-dinitropropyl)acetal) (CAS 5108-69-0);
4. BDNPF (bis (2,2-dinitropropyl)formal) (CAS 5917-61-3);
5. BTTN (butanetrioltrinitrate) (CAS 6659-60-5)
(see also 6A008.g.8 for its "precursors");
6. Energetic monomers, plasticizers or polymers, specially formulated for military use and containing any of the following:
a. Nitro groups;
b. Azido groups;
c. Nitrate groups;
d. Nitraza groups; or
e. Difluoroamino groups;
7. FAMAO (3-difluoroaminomethyl-3-azidomethyl oxetane) and its polymers;
8. FEFO (bis-(2-fluoro-2,2-dinitroethyl) formal) (CAS 17003-79-1);
9. FPF-1 (poly-2,2,3,3,4,4-hexafluoropentane-1,5-diol formal) (CAS 376-90-9);
10. FPF-3 (poly-2,4,4,5,5,6,6-heptafluoro-2-tri-fluoromethyl-3-oxaheptane-1,7-diol formal);
11. GAP (glycidylazide polymer) (CAS 143178-24-9) and its derivatives;
12. HTPB (hydroxyl terminated polybutadiene) with a hydroxyl functionality equal to or greater than 2.2 and less than or equal to 2.4, a hydroxyl value of less than 0.77 meq/g, and a viscosity at 30°C of less than 47 poise
(CAS 69102-90-5);
13. Alcohol functionalised poly(epichlorohydrin) with a molecular weight less than 10,000, as follows:
a. Poly(epichlorohydrindiol);
b. Poly(epichlorohydrintriol).
14. NENAs (nitratoethylnitramine compounds) (CAS 17096-47-8, 85068-73-1, 82486-83-7, 82486-82-6And 85954-06-9);
15. PGN (poly-GLYN, polyglycidylnitrate or poly(nitratomethyl oxirane)) (CAS 27814-48-8);
16. Poly-NIMMO (poly nitratomethylmethyloxetane), poly-NMMO or poly(3-Nitratomethyl-3- methyloxetane)) (CAS 84051-81-0);
17. Polynitroorthocarbonates;
18. TVOPA (1,2,3-tris[1,2-bis(difluoroamino)ethoxy] propane or tris vinoxy propane adduct) (CAS 53159- 39-0);
19. 4,5 diazidomethyl-2-methyl-1,2,3-triazole (iso- DAMTR);
20. PNO (Poly(3-nitrato oxetane));
6A008 f. "Additives" as follows:
Appendix 3 – SCOMET List
1. Basic copper salicylate (CAS 62320-94-9);
2. BHEGA (bis-(2-hydroxyethyl) glycolamide) (CAS 17409-41-5);
3. BNO (butadienenitrileoxide);
4. Ferrocene derivatives as follows:
a. Butacene (CAS 125856-62-4);
b. Catocene (2,2-bis-ethylferrocenyl propane) (CAS 37206-42-1);
c. Ferrocene carboxylic acids and ferrocene carboxylic acid esters;
d. n-butyl-ferrocene (CAS 31904-29-7);
e. Other adducted polymer ferrocene derivatives not specified elsewhere in 6A008.f.4;
f. Ethyl ferrocene (CAS 1273-89-8);
g. Propyl ferrocene;
h. Pentyl ferrocene (CAS 1274-00-6);
i. Dicyclopentyl ferrocene;
j. Dicyclohexyl ferrocene;
k. Diethyl ferrocene (CAS 1273-97-8);
l. Dipropyl ferrocene;
m. Dibutyl ferrocene (CAS 1274-08-4);
n. Dihexyl ferrocene (CAS 93894-59-8);
o. Acetyl ferrocene (CAS 1271-55-2)/1,1’-diacetyl ferrocene (CAS 1273-94-5);
5. Lead beta-resorcylate (CAS 20936-32-7);
6. Lead citrate (CAS 14450-60-3);
7. Lead-copper chelates of beta-resorcylate or salicylates (CAS 68411-07-4);
8. Lead maleate (CAS 19136-34-6);
9. Lead salicylate (CAS 15748-73-9);
10. Lead stannate (CAS 12036-31-6);
11. MAPO (tris-1-(2-methyl)aziridinyl phosphine oxide)
(CAS 57-39-6); BOBBA 8 (bis(2-methyl aziridinyl) 2-(2-hydroxypropanoxy) propylamino phosphine oxide); and other MAPO derivatives;
12. Methyl BAPO (bis(2-methyl aziridinyl) methylamino phosphine oxide) (CAS 85068-72-0);
13. N-methyl-p-nitroaniline (CAS 100-15-2);
14. 3-Nitraza-1,5-pentane diisocyanate (CAS 7406-61-9);
15. Organo-metallic coupling agents as follows:
a. Neopentyl[diallyl]oxy, tri[dioctyl]phosphato-titanate (CAS 103850-22-2); also known as titanium IV, 2,2[bis 2-propenolato-methyl, butanolato, tris (dioctyl) phosphato] (CAS 110438-25-0); or
LICA 12
(CAS 103850-22-2);
b. Titanium IV, [(2-propenolato-1) methyl, n-propanolatomethyl] butanolato-1, tris[dioctyl] pyrophosphate or KR3538;
c. Titanium IV, [(2-propenolato-1)methyl, n-propanolatomethyl] butanolato-1, tris(dioctyl)phosphate;
16. Polycyanodifluoroaminoethyleneoxide;
17. Bonding agents as follows:
a. 1,1R,1S-trimesoyl-tris(2-ethylaziridine) (HX-868, BITA)
(CAS 7722-73-8);
b. Polyfunctional aziridine amides with isophthalic, trimesic, isocyanuric or trimethyladipic backbone also having a 2-methyl or 2-ethyl aziridine group;
Note Item 6A008.f.17.b. includes:
a. 1,1H-Isophthaloyl-bis(2-methylaziridine)(HX-752)
(CAS 7652-64-4);
b. 2,4,6-tris(2-ethyl-1-aziridinyl)-1,3,5-triazine (HX-874) (CAS 18924-91-9);
c. 1,1'-trimethyladipoyl-bis(2-ethylaziridine) (HX-877)
(CAS 71463-62-2).
18. Propyleneimine (2-methylaziridine) (CAS 75-55-8);
19. Superfine iron oxide (Fe2O3) (CAS 1317-60-8) with a specific surface area more than 250 m2/g and an average particle size of 3.0 nm or less;
20. TEPAN (tetraethylenepentaamineacrylonitrile) (CAS 68412-45-3); cyanoethylated polyamines and their salts;
21. TEPANOL (tetraethylenepentaamineacrylonitrileglycidol) (CAS 68412-46-4); cyanoethylated Appendix 3 – SCOMET List
polyamines adducted with glycidol and their salts;
22. TPB (triphenyl bismuth) (CAS 603-33-8);
23. TEPB (Tris (ethoxyphenyl) bismuth) (CAS 90591-48-3);
6A008 g. "Precursors" as follows:
N.B. In 6A008.g the references are to specified "Energetic Materials" manufactured from these substances.
1. BCMO (3,3-bis(chloromethyl)oxetane) (CAS 78-71-7)
(see also 6A008.e.1 and e.2);
2. Dinitroazetidine-t-butyl salt (CAS 125735-38-8) (see also 6A008.a.28);
3. Hexaazaisowurtzitane derivates including HBIW (hexabenzylhexaazaisowurtzitane) (CAS 124782- 15-6) (see also 6A008.a.4) and TAIW (tetraacetyldibenzylhexaazaisowurtzitane) (CAS 182763-60-6) (see also 6A008.a.4);
4. (Reserved)
5. TAT (1,3,5,7 tetraacetyl-1,3,5,7,-tetraaza cyclo-octane) (CAS 41378-98-7) (see also 6A008.a.13);
6. 1,4,5,8-tetraazadecalin (CAS 5409-42-7) (see also 6A008.a.27);
7. 1,3,5-trichlorobenzene (CAS 108-70-3) (see also 6A008.a.23);
8. 1,2,4-trihydroxybutane (1,2,4-butanetriol) (CAS 3068-00-6)
(see also 6A008.e.5);
9. DADN (1,5-diacetyl-3,7-dinitro-1, 3, 5, 7-tetraaza-cyclooctane) (see also 6A008.a.13).
6A008 h. 'Reactive material' powders and shapes, as follows:
1. Powders of any of the following materials, with a particle size less than 250 µm in any direction and not specified elsewhere by 6A008:
a. Aluminium;
b. Niobium;
c. Boron;
d. Zirconium;
e. Magnesium;
f. Titanium;
g. Tantalum;
h. Tungsten;
i. Molybdenum; or
j. Hafnium;
2. Shapes, not specified by 6A003, 6A004, 6A012 or 6A016, fabricated from powders specified by 6A008.h.1.
Technical Notes
1. 'Reactive materials' are designed to produce an exothermic reaction only at high shear rates and for use as liners or casings in warheads.
2. 'Reactive material' powders are produced by, for example, a high energy ball milling process.
3. 'Reactive material' shapes are produced by, for example, selective laser sintering.
Note 1 6A008 does not apply to the following substances unless they are compounded or mixed with the "energetic material" specified by 6A008.a. or powdered metals specified by 6A008.c:
a. Ammonium picrate (CAS 131-74-8);
b. Black powder;
c. Hexanitrodiphenylamine (CAS 131-73-7);
d. Difluoroamine (CAS 10405-27-3);
e. Nitrostarch (CAS 9056-38-6);
f. Potassium nitrate (CAS 7757-79-1);
g. Tetranitronaphthalene;
h. Trinitroanisol;
i. Trinitronaphthalene;
j. Trinitroxylene;
k. N-pyrrolidinone; 1-methyl-2-pyrrolidinone (CAS 872-50-4);
l. Dioctylmaleate (CAS 142-16-5);
m. Ethylhexylacrylate (CAS 103-11-7);
Appendix 3 – SCOMET List
n. Triethylaluminium (TEA) (CAS 97-93-8), trimethylaluminium (TMA) (CAS 75-24-1), and other pyrophoric metal alkyls and aryls of lithium, sodium, magnesium, zinc or boron;
o. Nitrocellulose (CAS 9004-70-0);
p. Nitroglycerin (or glyceroltrinitrate, trinitroglycerine) (NG)
(CAS 55-63-0);
q. 2,4,6-trinitrotoluene (TNT) (CAS 118-96-7);
r. Ethylenediaminedinitrate (EDDN) (CAS 20829-66-7);
s. Pentaerythritoltetranitrate (PETN) (CAS 78-11-5);
t. Lead azide (CAS 13424-46-9), normal lead styphnate (CAS 15245-44-0) and basic lead styphnate (CAS 12403-82-6), and primary explosives or priming compositions containing azides or azide complexes;
u. Triethyleneglycoldinitrate (TEGDN) (CAS 111-22-8);
v. 2,4,6-trinitroresorcinol (styphnic acid) (CAS 82-71-3);
w. Diethyldiphenylurea; (CAS 85-98-3); dimethyldiphenylurea;
(CAS 611-92-7), methylethyldiphenylurea; [Centralites]
x. N,N-diphenylurea (unsymmetrical diphenylurea) (CAS 603-54-3);
y. Methyl-N,N-diphenylurea (methyl unsymmetrical diphenylurea)
(CAS 13114-72-2);
z. Ethyl-N,N-diphenylurea (ethyl unsymmetrical diphenylurea)
(CAS 64544-71-4);
aa. 2-Nitrodiphenylamine (2-NDPA) (CAS 119-75-5);
bb. 4-Nitrodiphenylamine (4-NDPA) (CAS 836-30-6);
cc. 2,2-dinitropropanol (CAS 918-52-5);
dd. Nitroguanidine (CAS 556-88-7) (see 8C111.d.).
Note 2 6A008 does not apply to ammonium perchlorate (6A008.d.2), NTO (6A008.a.18) or catocene (6A008.f.4.b), and meeting all of the following:
a. Specially shaped and formulated for civil-use gas generation devices;
b. Compounded or mixed, with non-active thermoset binders or plasticizers, and having a mass of less than 250 g;
c. Having a maximum of 80% ammonium perchlorate (6A008.d.2) in mass of active material;
d. Having less than or equal to 4 g of NTO (6A008.a.18); and
e. Having less than or equal to 1 g of catocene (6A008.f.4.b).
6A009 Vessels of war (surface or underwater), special naval equipment, accessories, components and other surface vessels, as follows:
N.B. For guidance and navigation equipment, see 6A011.
a. Vessels and components, as follows:
1. Vessels (surface or underwater) specially designed or modified for military use, regardless of current state of repair or operating condition, and whether or not they contain weapon delivery systems or armour, and hulls or parts of hulls for such vessels, and components therefor specially designed for military use;
2. Surface vessels, other than those specified in 6A009.a.1, having any of the following, fixed or integrated into the vessel:
a. Automatic weapons specified in 6A001 or weapons specified in 6A002, 6A004, 6A012, or 6A019, or 'mountings' or hard points for weapons having a calibre of 12.7 mm or greater; Technical Note
'Mountings' refers to weapon mounts or structural strengthening for the purpose of installing weapons.
b. Fire control systems specified in 6A005;
c. Having all of the following:
1. 'Chemical, Biological, Radiological and Nuclear (CBRN) protection'; and
2. 'Pre-wet or wash down system' designed for decontamination purposes; or Technical Notes
1. 'CBRN protection' is a self-contained interior space containing features such as overpressurization, isolation of ventilation systems, limited ventilation openings with CBRN
Appendix 3 – SCOMET List
filters and limited personnel access points incorporating air-locks.
2. 'Pre-wet or wash down system' is a seawater spray system capable of simultaneously
wetting the exterior superstructure and decks of a vessel.
| . | d. | Active weapon countermeasure systems specified in 6A004.b, 6A005.c or 6A011.a and having any of the following: 1. 'CBRN protection'; 2. Hull and superstructure, specially designed to reduce the radar cross section; 3. Thermal signature reduction devices, (e.g, an exhaust gas cooling system), excluding those specially designed to increase overall power plant efficiency or to reduce the environmental impact; or 4. A degaussing system designed to reduce the magnetic signature of the whole vessel; |
6A009 b. Engines and propulsion systems, as follows, specially designed for military use and components therefor specially designed for military use:
1. Diesel engines specially designed for submarines and having all of the following:
a. Power output of 1.12 MW (1,500 hp) or more; and
b. Rotary speed of 700 rpm or more;
. 2. Electric motors specially designed for submarines and having all of the following:
a. Power output of more than 0.75 MW (1,000 hp);
b. Quick reversing;
c. Liquid cooled; and
d. Totally enclosed;
3. Non-magnetic diesel engines having all of the following:
a. Power output of 37.3 kW (50 hp) or more; and
b. Non-magnetic content in excess of 75% of total mass;
4. 'Air Independent Propulsion' (AIP) systems specially designed for submarines; Technical Note
'Air Independent Propulsion' (AIP) allows a submerged submarine to operate its propulsion system, without access to atmospheric oxygen, for a longer time than the batteries would have otherwise
allowed. For the purposes of 6A009.b.4, AIP does not include nuclear power.
6A009 c. Underwater detection devices, specially designed for military use, controls therefor and components therefor specially designed for military use;
d. Anti-submarine nets and anti-torpedo nets, specially designed for military use;
e. (Reserved)
f. Hull penetrators and connectors, specially designed for military use, that enable interaction with equipment external to a vessel, and components therefor specially designed for military use;
Note 6A009.f includes connectors for vessels which are of the single-conductor, multi-conductor, coaxial or waveguide type, and hull penetrators for vessels, both of which are capable of remaining impervious to leakage from without and of retaining required characteristics at marine depths exceeding 100 m; and fibre-optic connectors and optical hull penetrators, specially designed for "laser" beam transmission, regardless of depth. 6A009.f. does not apply to ordinary propulsive shaft and hydrodynamic control-rod hull penetrators.
6A009 g. Silent bearings having any of the following, components therefor and equipment containing those bearings, specially designed for military use:
1. Gas or magnetic suspension;
2. Active signature controls; or
3. Vibration suppression controls.
6A010 "Aircraft", "lighter-than-air vehicles", "Unmanned Aerial Vehicles" ("UAVs"), aero-engines and "aircraft" equipment, related equipment, and components, as follows, specially designed or modified for military use: N.B. For guidance and navigation equipment, see 6A011.
Appendix 3 – SCOMET List
a. Manned "aircraft" and "lighter-than-air vehicles", and specially designed components therefor;
b. (Reserved)
c. Unmanned "aircraft" and "lighter-than-air vehicles", and related equipment, as follows, and specially designed components therefor:
1. "UAVs", Remotely Piloted Air Vehicles (RPVs), autonomous programmable vehicles and unmanned "lighter-than-air vehicles";
2. Launchers, recovery equipment and ground support equipment;
3. Equipment designed for command or control;
d. Propulsion aero-engines and specially designed components therefor;
e. Airborne refuelling equipment specially designed or modified for any of the following, and specially designed components therefor:
1. "Aircraft" specified by 6A010.a; or
2. Unmanned "aircraft" specified by 6A010.c;
f. 'Ground equipment' specially designed for "aircraft" specified by 6A010.a or aero-engines specified by 6A010.d;
Technical Note
'Ground equipment' includes pressure refuelling equipment and equipment designed to facilitate operations in confined areas.
g. Aircrew life support equipment, aircrew safety equipment and other devices for emergency escape,
not specified in 6A010.a, designed for "aircraft" specified by 6A010.a;
Note 6A010.g does not control aircrew helmets that do not incorporate, or have mountings or
fittings for, equipment specified in Category 6.
N.B. For helmets see also 6A013.c.
h. Parachutes, paragliders and related equipment, as follows, and specially designed components therefor:
1. Parachutes not specified elsewhere in Category 6;
2. Paragliders;
3. Equipment specially designed for high altitude parachutists (e.g, suits, special helmets, breathing systems, navigation equipment);
i. Controlled opening equipment or automatic piloting systems, designed for parachuted loads.
Note 1 6A010.a does not apply to "aircraft" and "lighter-than-air vehicles" or variants of those "aircraft", specially designed for military use and which are all of the following:
a. Not a combat "aircraft";
b. Not configured for military use and not fitted with equipment or attachments specially designed or modified for military use; and
c. Certified for civil use by civil aviation authority of India
Note 2 6A010.d does not apply to:
a. Aero-engines designed or modified for military use which have been certified by civil aviation authority of India,for use in “civil aircraft” or specially designed components therefor;
b. Reciprocating engines or specially designed components therefor, except those specially designed for "UAVs".
Note 3 For the purposes of 6A010.a, and 6A010.d, specially designed components and related equipment for nonmilitary "aircraft" or aero-engines modified for military use applies only to those military components and to military related equipment required for the modification to military use.
Note 4 For the purposes of 6A010.a, military use includes: combat, military reconnaissance, assault, military training, logistics support, and transporting and airdropping troops or military equipment.
Note 5 6A010.a does not apply to "aircraft" that meet all of the following:
a. Were first manufactured before 1946;
b. Do not incorporate items specified by Category 6 unless the items are required to meet safety or
airworthiness standards of civil aviation authority of India; and
c. Do not incorporate weapons specified by Category 6 unless inoperable and incapable of being
Appendix 3 – SCOMET List
returned to operation.
6A011 Electronic equipment, "spacecraft" and components, not specified elsewhere on Category 6, as follows:
a. Electronic equipment specially designed for military use and specially designed components therefor;
Note 6A011.a includes:
a. Electronic countermeasure and electronic counter-countermeasure equipment (i.e, equipment designed to introduce extraneous or erroneous signals into radar or radio communication receivers or otherwise hinder the reception, operation or effectiveness of adversary electronic receivers including their countermeasure equipment), including jamming and counter-jamming equipment;
b. Frequency agile tubes;
c. Electronic systems or equipment, designed either for surveillance and monitoring of the electromagnetic spectrum for military intelligence or security purposes or for counteracting such surveillance and monitoring;
d. Underwater countermeasures, including acoustic and magnetic jamming and decoy, equipment designed to introduce extraneous or erroneous signals into sonar receivers;
e. Data processing security equipment, data security equipment and transmission and signalling
line security equipment, using ciphering processes;
f. Identification, authentification and keyloader equipment and key management, manufacturing and distribution equipment;
g. Guidance and navigation equipment;
h. Digital troposcatter-radio communications transmission equipment;
i. Digital demodulators specially designed for signals intelligence;
j. "Automated Command and Control Systems".
N.B. For "software" associated with military "Software" Defined Radio (SDR), see 6A021.
6A011 b. Global Navigation Satellite Systems (GNSS) jamming equipment and specially designed components therefor;
6A011 c. "Spacecraft" specially designed or modified for military use, and "spacecraft" components specially designed for military use.
6A012 High velocity kinetic energy weapon systems and related equipment, as follows, and specially designed components therefor:
a. Kinetic energy weapon systems specially designed for destruction or effecting mission-abort of a target;
b. Specially designed test and evaluation facilities and test models, including diagnostic instrumentation and targets, for dynamic testing of kinetic energy projectiles and systems.
N.B. For weapon systems using sub-calibre ammunition or employing solely chemical propulsion, and ammunition therefor, see 6A001 to 6A004.
Note 1 6A012 includes the following when specially designed for kinetic energy weapon systems:
a. Launch propulsion systems capable of accelerating masses larger than 0.1 g to velocities in
excess of 1.6 km/s, in single or rapid fire modes;
b. Prime power generation, electric armour, energy storage (e.g, high energy storage capacitors), thermal management, conditioning, switching or fuel-handling equipment; and electrical interfaces between power supply, gun and other turret electric drive functions; N.B. See also 8A301.e.2 for high energy storage capacitors.
c. Target acquisition, tracking, fire control or damage assessment systems;
d. Homing seeker, guidance or divert propulsion (lateral acceleration) systems for projectiles.
Appendix 3 – SCOMET List
Note 2 6A012 applies to weapon systems using any of the following methods of propulsion:
a. Electromagnetic;
b. Electrothermal;
c. Plasma;
d. Light gas; or
e. Chemical (when used in combination with any of the above).
6A013 Armoured or protective equipment, constructions and components, as follows:
a. Metallic or non-metallic armoured plate, having any of the following:
1. Manufactured to comply with a military standard or specification; or
2. Suitable for military use;
N.B. For body armour plate, see 6A013.d.2.
b. Constructions of metallic or non-metallic materials, or combinations thereof, specially designed to provide ballistic protection for military systems, and specially designed components therefor;
c. the relevant manufactured according to military standards or specifications, and specially designed helmet shells, liners, or comfort pads, therefor;
N.B. For other military helmet components or accessories, see the relevant Category entry.
d. Body armour or protective garments, and components therefor, as follows:
1. Soft body armour or protective garments, manufactured to military standards or specifications, or to their equivalents, and specially designed components therefor;
Note For the purposes of 6A013.d.1, military standards or specifications include, at a minimum, specifications for fragmentation protection.
2. Hard body armour plates providing ballistic protection equal to or greater than level III (NIJ 0101.06, July 2008).
Note 1 6A013.b includes materials specially designed to form explosive reactive armour or to construct military shelters.
Note 2 6A013.c does not apply to conventional steel helmets, neither modified or designed to accept, nor equipped with any type of accessory device.
Note 3 6A013.c and d. do not apply to helmets, body armour or protective garments, when accompanying their user for the user's own personal protection.
Note 4 The only helmets specially designed for bomb disposal personnel that are specified by 6A013 are those specially designed for military use.
N.B. 1 See also 8A105.
N.B. 2 For "fibrous or filamentary materials" used in the manufacture of body armour and helmets, see 8C110.
6A014 'Specialised equipment for military training' or for simulating military scenarios, simulators specially designed for training in the use of any firearm or weapon specified by 6A001 or 6A002 and specially designed components and accessories therefor.
Technical Note
The term 'specialised equipment for military training' includes military types of attack trainers, operational flight trainers, radar target trainers, radar target generators, gunnery training devices, anti-submarine warfare trainers, flight simulators (including human-rated centrifuges for pilot/astronaut training), radar trainers, instrument flight trainers, navigation trainers, missile launch trainers, target equipment, drone "aircraft", armament trainers, pilotless "aircraft" trainers, mobile training units and training equipment for ground military operations.
Note 1 6A014 includes image generating and interactive environment systems for simulators, when specially designed or modified for military use.
Note 2 6A014 does not apply to equipment specially designed for training in the use of hunting or sporting
Appendix 3 – SCOMET List
weapons.
6A015 Imaging or countermeasure equipment, as follows, specially designed for military use, and specially designed components and accessories therefor:
a. Recorders and image processing equipment;
b. Cameras, photographic equipment and film processing equipment;
c. Image intensifier equipment;
d. Infrared or thermal imaging equipment;
e. Imaging radar sensor equipment;
f. Countermeasure or counter-countermeasure equipment, for the equipment specified by 6A015.a to 6A015.e.
Note 6A015.f includes equipment designed to degrade the operation or effectiveness of military imaging systems or to minimize such degrading effects.
Note 1 In 6A015 the term specially designed components includes the following, when specially designed for military use:
a. Infrared image converter tubes;
b. Image intensifier tubes (other than first generation);
c. Microchannel plates;
d. Low-light-level television camera tubes;
e. Detector arrays (including electronic interconnection or read out systems);
f. Pyroelectric television camera tubes;
g. Cooling systems for imaging systems;
h. Electrically triggered shutters of the photochromic or electro-optical type having a shutter speed of less than 100 µs, except in the case of shutters which are an essential part of a high speed camera;
i. Fibre optic image inverters;
j. Compound semiconductor photocathodes.
Note 2 6A015 does not apply to "first generation image intensifier tubes" or equipment specially designed to
incorporate "first generation image intensifier tubes".
N.B. For the classification of weapons sights incorporating "first generation image intensifier
tubes" see 6A001, 6A002, and 6A005.a.
N.B. See also 8A602.a.2 and 8A602.b.
6A016 Forgings, castings and other unfinished products, specially designed for items specified by 6A001, to 6A004, 6A006, 6A009, 6A010, 6A012, or 6A019.
Note 6A016 applies to unfinished products when they are identifiable by material composition, geometry or function.
6A017 Miscellaneous equipment, materials and "libraries", as follows, and specially designed components therefor:
a. Diving and underwater swimming apparatus, specially designed or modified for military use, as follows:
1. Self-contained diving rebreathers, closed or semi-closed circuit;
2. Underwater swimming apparatus specially designed for use with the diving apparatus specified in 6A017.a.1;
N.B. See also 8A802.q.
b. Construction equipment specially designed for military use;
c. Fittings, coatings and treatments, for signature suppression, specially designed for military use;
d. Field engineer equipment specially designed for use in a combat zone;
e. "Robots", "robot" controllers and "robot" "end-effectors", having any of the following characteristics:
1. Specially designed for military use;
2. Incorporating means of protecting hydraulic lines against externally induced punctures caused by ballistic fragments (e.g, incorporating self-sealing lines) and designed to use hydraulic fluids with flash points higher than 839 K (566°C); or
3. Specially designed or rated for operating in an electro-magnetic pulse (EMP) environment; Technical Note
Appendix 3 – SCOMET List
Electro-magnetic pulse does not refer to unintentional interference caused by electromagnetic radiation from nearby equipment (e.g, machinery, appliances or electronics) or lightning.
f. "Libraries" specially designed or modified for military use with systems, equipment or components, specified by Category 6;
g. Nuclear power generating equipment or propulsion equipment, including "nuclear reactors", specially designed for military use and components therefor specially designed or 'modified' for military use; N.B (See Commodity Identification Note of SCOMET list)
h. Equipment and material, coated or treated for signature suppression, specially designed for military use, other than those specified elsewhere in Category 6;
i. Simulators specially designed for military "nuclear reactors";
N.B (See Commodity Identification Note of SCOMET list)
j. Mobile repair shops specially designed or 'modified' to service military equipment;
k. Field generators specially designed or 'modified' for military use;
l. Containers specially designed or 'modified' for military use;
m. Ferries, other than those specified elsewhere in Category 6, bridges and pontoons, specially designed for military use;
n. Test models specially designed for the "development" of items specified by 6A004, 6A006, 6A009, or 6A010;
o. "Laser" protection equipment (e.g, eye and sensor protection) specially designed for military use;
p. "Fuel cells", other than those specified elsewhere in Category 6, specially designed or 'modified' for military use.
Technical Note
1. (Reserved)
2. For the purpose of 6A017, 'modified' means any structural, electrical, mechanical, or other change that provides a non-military item with military capabilities equivalent to an item which is specially designed for military use.
6A018 'Production' equipment and components, as follows:
a. Specially designed or modified 'production' equipment for the 'production' of products specified by Category 6, and specially designed components therefor;
b. Specially designed environmental test facilities and specially designed equipment therefor, for the
certification, qualification or testing of products specified by Category 6.
Technical Note
For the purposes of 6A018 the term 'production' includes design, examination, manufacture, testing and checking.
Note 6A018.a and 6A018.b include the following equipment:
a. Continuous nitrators;
b. Centrifugal testing apparatus or equipment, having any of the following:
1. Driven by a motor or motors having a total rated horsepower of more than 298 kW (400 hp);
2. Capable of carrying a payload of 113 kg or more; or
3. Capable of exerting a centrifugal acceleration of 8 g or more on a payload of 91 kg or more;
c. Dehydration presses;
d. Screw extruders specially designed or modified for military "explosive" extrusion;
e. Cutting machines for the sizing of extruded "propellants";
f. Sweetie barrels (tumblers) 1.85 m or more in diameter and having over 227 kg product capacity;
g. Continuous mixers for solid "propellants";
h. Fluid energy mills for grinding or milling the ingredients of military "explosives";
i. Equipment to achieve both sphericity and uniform particle size in metal powder listed in 6A008.c.8;
j. Convection current converters for the conversion of materials listed in 6A008.c.3.
6A019 Directed Energy Weapon (DEW) systems, related or countermeasure equipment and test models, as follows, and specially designed components therefor:
Appendix 3 – SCOMET List
a. "Laser" systems specially designed for destruction or effecting mission-abort of a target;
b. Particle beam systems capable of destruction or effecting mission-abort of a target;
c. High power Radio-Frequency (RF) systems capable of destruction or effecting mission-abort of a target;
d. Equipment specially designed for the detection or identification of, or defence against, systems specified by 6A019.a to 6A019.c;
e. Physical test models for the systems, equipment and components, specified by 6A019.
f. "Laser" systems specially designed to cause permanent blindness to unenhanced vision, i.e, to the naked eye or to the eye with corrective eyesight devices.
Note 1 DEW systems specified by 6A019 include systems whose capability is derived from the controlled application of:
a. "Lasers" of sufficient power to effect destruction similar to the manner of conventional ammunition;
b. Particle accelerators which project a charged or neutral particle beam with destructive power;
c. High pulsed power or high average power radio frequency beam transmitters, which produce fields sufficiently intense to disable electronic circuitry at a distant target.
Note 2 6A019 includes the following when specially designed for DEW systems:
a. Prime power generation, energy storage, switching, power conditioning or fuel-handling equipment;
b. Target acquisition or tracking systems;
c. Systems capable of assessing target damage, destruction or mission-abort;
d. Beam-handling, propagation or pointing equipment;
e. Equipment with rapid beam slew capability for rapid multiple target operations;
f. Adaptive optics and phase conjugators;
g. Current injectors for negative hydrogen ion beams;
h. "Space-qualified" accelerator components;
i. Negative ion beam funnelling equipment;
j. Equipment for controlling and slewing a high energy ion beam;
k. "Space-qualified" foils for neutralising negative hydrogen isotope beams.
6A020 Cryogenic and "superconductive" equipment, as follows, and specially designed components and accessories therefor:
a. Equipment specially designed or configured to be installed in a vehicle for military ground, marine, airborne or space applications, capable of operating while in motion and of producing or maintaining temperatures below 103 K (- 170°C);
Note 6A020.a includes mobile systems incorporating or employing accessories or components manufactured from non-metallic or non-electrical conductive materials, such as plastics or epoxyimpregnated materials.
b. "Superconductive" electrical equipment (rotating machinery and transformers) specially designed or configured to be installed in a vehicle for military ground, marine, airborne or space applications and capable of operating while in motion.
Note 6A020.b does not apply to direct-current hybrid homopolar generators that have single-pole normal metal armatures which rotate in a magnetic field produced by superconducting windings, provided
those windings are the only superconducting components in the generator.
6A021 "Software" as follows:
a. "Software" specially designed or modified for any of the following:
1. "Development", "production", operation or maintenance of equipment specified by Category 6;
2. "Development" or "production" of materials specified by Category 6; or
3. "Development", "production", operation or maintenance of "software" specified by Category 6.
b. Specific "software", other than that specified by 6A021.a as follows:
1. "Software" specially designed for military use and specially designed for modelling, simulating or evaluating military weapon systems;
2. "Software" specially designed for military use and specially designed for modelling or simulating military operational scenarios;
Appendix 3 – SCOMET List
3. "Software" for determining the effects of conventional, nuclear, chemical or biological weapons;
4. "Software" specially designed for military use and specially designed for Command, Communications, Control and Intelligence (C3I) or Command, Communications, Control, Computer and Intelligence (C4I) applications;
c. "Software", not specified by 6A021.a or 6A021b specially designed or modified to enable equipment not specified by Category 6 to perform the military functions of equipment specified by Category 6.
6A022 "Technology" as follows:
a. "Technology", other than specified in 6A022.b which is "required" for the "development", "production", operation, installation, maintenance (checking), repair, overhaul or refurbishing of items specified in Category 6;
b. "Technology" as follows:
1. "Technology" "required" for the design of, the assembly of components into, and the operation, maintenance and repair of, complete production installations for items specified by Category 6, even if
the components of such production installations are not specified;
2. "Technology" "required" for the "development" and "production" of small arms, even if used to produce reproductions of antique small arms;
3. (Reserved)
4. (Reserved)
5. "Technology" "required" exclusively for the incorporation of "biocatalysts", specified by 6A007.i.1 into military carrier substances or military material.
Note 1 "Technology" "required" for the "development", "production", operation, installation, maintenance (checking), repair, overhaul or refurbishing of items specified by Category 6 remains under control
even when applicable to any item not specified by Category 6.
Note 2 6A022 does not apply to:
a. "Technology" that is the minimum necessary for the installation, operation, maintenance (checking) or repair, of those items which are not controlled or whose export has been authorised;
b. "Technology" that is "in the public domain", "basic scientific research" or the minimum necessary information for patent applications.
c. "Technology" for magnetic induction for continuous propulsion of civil transport devices.
Appendix 3 – SCOMET List
Category 7: Electronics, computers, and information technology including information security
7A Electronics
7A001 High-power microwave devices including tubes, travelling wave tubes (TWT) and phase shifters, and continuous wave and pulsed high power microwave travelling wave tube amplifiers (TWTA) operating at frequencies higher than 31 GHz, and their power supplies.
7A002 Microwave monolithic integrated circuits (MMIC) operating at frequencies above 3 GHz and surface acoustic wave (SAW) devices operating at frequencies above 2.5 GHz.
7A003 Phased array antennas and their elements
7A004 Radiation-hardened microprocessors, field programmable gate arrays and solid state memory devices
7A005 Microprocessor microcircuits, microcomputer microcircuits, microcontroller microcircuits, storage integrated circuits manufactured from a compound semiconductor, analogueto-digital converter, and digital-to-analogue converter, printed circuit boards or modules, electrooptical or optical integrated circuits designed for signal processing, field programmable logic devices, neural network integrated circuits, custom integrated circuits for which either the function is unknown or the control status of the equipment in which the integrated circuit will be used is unknown, Fast Fourier Transform (FFT) processors, electrical erasable programmable read-only memories (EEPROMs), flash memories or static random-access memories (SRAMs), having any of the following:
a. Rated for operation at an ambient temperature above 398 K (+125°C);
| b. | Rated for operation at an ambient temperature below 218 K (-55°C); or |
| c. | Rated for operation over the entire ambient temperature range from 218 K (-55°C) to 398 K (+125°C). |
7A006 Radiation-hardened analogue-to-digital and digital-to-analogue converter integrated circuits, as follows:
a. Analogue-to-digital converters having any of the following:
1. A resolution of 8 bit or more, but less than 12 bit, with a total conversion time of less than 5 ns;
2. A resolution of 12 bit with a total conversion time of less than 200 ns; or
3. A resolution of more than 12 bit with a total conversion time of less than 2 µs;
b. Digital-to-analogue converters with a resolution of 12 bit or more, and a settling time of less than 10 ns.
7A007 Detector units operating in the thermal infrared, ultraviolet, x-ray and gamma ray spectrum.
7A008 Focal plane assemblies for imaging cameras operating in the visible, near and thermal infrared spectrum
7A009 Technology for the development, production or use of items specified in 7A005 and 7A006.
7A010 Analogue-to-digital converters, usable in the systems specified in 5A, having any of the following characteristics:
a. Designed to meet military specifications for ruggedised equipment; or
b. Designed or modified for military use and being any of the following types:
1. Analogue-to-digital converter microcircuits, which are radiation-hardened or have
Original document: View the PDF.